Search results

Can you rip down a couple pieces of freeflow tiles or some other support structure to level it out more and tile over that with freeflow?

Big fan of your Racedeck design choice. :D

This is so cool. I bet if you ran some 1x2 pine along the studs on that canvas it would turn out really polished. Maybe stain it to match the reclaimed wood?

Turned wrenches for the first time on my new-to-me truck. Pulled off the leveling kit that my uncle (the previous owner) had put on since I prefer it to have stock suspension. Lifting this behemoth with my floor jack, I could tell that it's a LOT heavier than anything I'd tried to lift before...

I doubt a ricochet would have enough speed to imbed itself in safety glasses. It would have still done damage to his eye, but would have just bounced off the glasses. This guy was either not running a guard or was standing on the wrong side of it.

Any kind of solid steel is going to be a pain with a recip saw. I had to cut off 1/2" bolts that were sheathed in 1.5" OD sleeves on my Jeep. They ate up saw blades and barely got touched. I ended up using a 9" cutoff wheel and oversized grinder to finish that job.

I built a ramp out of GC 2x12. Ripped 4 foot lengths diagonally into triangles and decked it with 5/4 x 6 deck boards horizontally. Ended up being a ~12" rise over 48" (3:12 slope), but because the deck boards are horizontal, they end up being great for grip. I've never had an issue with grip...

Be aware, swapping sides is a wiring pain AND it'll just swap the time of day when this happens. I'll sometimes have issues in the mornings. Neighbors across the street will sometimes have issues in the evenings. YMMV.

I think he meant that the top shelves of those cabinets in your sketchup are going to be 8+ feet in the air and you won't be able to reach anything on them. Might as well go with shorter cabinets and store infrequently used items on top of them.

800 lbs, plus friction in the fulcrum, plus the weight of the 16' length multiplied by the distance to its center of mass (~8') minus the weight of the 4' length multiplied the distance to its center of mass (~2') times your mechanical advantage (1:4 or 0.25).

The point of a lever is to provide mechanical advantage. What's your goal? Is it to be able to lift the 200 pounds with 50 pounds of force? Is it to counterbalance the weight? Do you need to lift 16' exactly or can you overshoot? Your max height should be a bit more than 16' to account for...

I have half of my garage freeflow (under the wife's DD) and half diamond tread (under my Jeep so I can keep an eye on any fluid leaks and it's easier on the knees when working on it). My racedeck has been down for about 14 months now and here's my unbiased review: - Freeflow is everything it's...

If you're lifting the car 1", you're going to be lifting much more than 1/4 the weight.

Is it common for these things to actually trip breakers? Having too big of a breaker shouldn't be an issue unless you have a short of some kind causing excess power draw and even then, having a smaller breaker isn't going to save the unit.

If the surface you're trying to support your vehicle on isn't flat enough to prevent a 4-legged jack stand from rocking, you need to think long and hard about why you're jacking up and getting under your vehicle in that location.

That's basically what my dad has. He could fit his corvette on a 4-post lift and drive the hood of a Tahoe underneath it to fit 4 cars in that space. All through high school my brother and I parked two jeeps in the deep 3rd stall. Now he only has 2 cars and the extended area is a nice...

My garage is just a 2 car attached garage. What I did well: - It's slightly oversized at 22x24 - There's a 240V hookup for my welder - It's finished drywalled and painted What I didn't do well: - Poor Lighting - Not enough 120V outlets - Should have done 2 or 3 240V outlets, not just one -...

> Reduces the space I have to heat/cool. An uninsulated stud wall isn't going to do diddly for reducing heating or cooling load. > Keeps dust and dirt from infiltrating one way or the other Dust suppression is easier done at the source rather than with a partition. > keeps all the junk from...

IMO, the stud wall to separate the space is a in and of itself a waste of space. Throw up a curtain instead. No damage to the building or the vehicle will result from the curtain being hit with a door and it can be pushed aside if she's trying to carry large items into or out of the car. And...

We did our own test, set out in the basement living room. Plenty of airflow, and where we spend a lot of our time. The EPA publishes a map that shows areas at high risk for elevated Radon levels. Most of Illinois is in the elevated area. From what I hear, if you have a lot of coal mining...