Search results

depends where you live. if you live in the snow belt and will be bringing in vehicles full of snow and snowmobiles etc. like i do you will have water problems. Where i am from if you are smart you put a concrete pinned curb atop the slab and stick frame above the curb. In my case I have a 8"...

First find out how man inches you paid for if you in fact paid for 7.5" you can use a wire and stab it into the spray foam and measure how deep it is on average. Do the same where you feel you are shorted what ever the difference is, is how much you are short.

any input guys?

hey guys so i was ready to buy a jack but i have come across a minor issue and i wanted your input as Rotary doesnt seem to be much help. So after doing some searching Rotary designed there hoist and jack combo to run on the TOP of the rails not in the rails. See link below to for the factory...

do you mind posting a few photos of the Dannmar i cant find any decent photos online, does it have wheels that run on a track/channel like the Atlas RJ6000 that Lelandwelds posted? like this: http://www.gregsmithequipment.com/Product%20Images/ATPK-RJ6-08.jpg?resizeid=3&resizeh=500&resizew=500

awesome guys thanks! i always buy from Summit or get stuff shipping to the US border as i only live 1 hour away so shipping is usually free or cheaper and then i clear customs myself. Would you guys vote on building two bridge plates that accommodates bottle jacks or buy 1 bridge jack and...

hey there, I have a 11,000 LBS Rotary that i bought used for cheap it was certified last time it was used in 2014 and has been sitting since. It does not have bridge jacks and i have been looking for a used set for a while but nothing really comes up. I dont want to buy brand new ($2,500 each...

Would you guys say it's a made in USA jack or a Chinese replica?

See the attached link. There are no markings on the jack, no stamped plate or no made in USA anything. https://www.kijiji.ca/v-tool-other/winnipeg/snap-on-battery-alt-tester/1291543468?enableSearchNavigationFlag=true Thanks

hey there i am building a new shop and now is the time to pick my overhead door track type. I will have 3 - 10x10 doors in a 12' tall wall BUT i have cathedral ceilings in the shop so in the center i have 14'. So my question is what works best should i have them go up as high as possible then...

i had a flatbed with a tilt deck truck pick up my 4 post. He showed up, tilted his deck, winched it up strapped down in 30 mins.

haha funny. The pawn shop i picked it up at said they will do exchanges for the same value.

Got this guy for Christmas it's a smal Chicago Majestic 34 I don't know much about it. One thing is that it has smooth faced jaws and pipe jaws? To me that doesn't make sense. Any thoughts? Should I keep it or exchange for a newer made in USA jack that they also have in stock.

I have no boundaries, electric service only. The reason I figure 2' from the door is enough because the doors are 10' wide and a vehicle is about 7-8' so if I drive straight in I now have about 3' from the door to the wall. My Sierra measures 20' long and my Jeep Grand Cherokee is 16' long. I...

I would LOVE a 40x60 and yes i know that bigger is better, but i dont want to go broke over the garage. My last shop was 24x34 so this one is a bit bigger.:beer:

hey all im looking a building a new shop. I cannot figure out which way i should orientate it. The garage will be heated as I have a very cold winter where i am. The shop will be used as storage for my car and tractor, a hoist one day and storage for all my tools. ( 60 gallon compressor, tool...

Spring hinge need to be adjusted a few times at installation then they are good to go, however they dont have the same "power" as a full hydraulic door closer and will eventually wear out. In my shop i have two spring hinges on the door just to get it to close automatically. If this door will...

So i just got off the phone with the old fella selling it, hes a type of guy that doesn't want to talk or BS old and miserable is the right word i guess. I cant look at it today but he took a verbal offer for $50.00 and a Crown Royal Whiskey. Now i dont want to bring home a dam paper weight...

I am going to look at it again tomorrow. Any thing I should look for to ensure its good? How long should it take to pump up? Obviously it shouldn't leak but any tell tale signs it's no good and might need a new ram?

What does the top pull on the handle do? I see that it raises a pin to move it to a different position??