Search results

Thank you, now I just have to drive ground rods and connect to the main panel Sent from my E6782 using Tapatalk

Yes, I twisted the grounds and secured them between two fender washers tightened with the ground screw...which I forgot to paint green. Sent from my E6782 using Tapatalk

Well I did my crawlspace work tonight, splicing 6/3 romex to 6 gauge thwn with 10 gauge ground. I should have used a bigger box and mounted it sideways, other than that and spilling my beer multiple times it went well. Questions...comments...keep in mind I'm not a professional. Sent from my...

I was under the assumption that I didn't need ground rods but after a bit of reading you are correct. So..two 1/2''x8' copper clad ground rods 6' apart with #6 solid copper ran through 1/2 sch80 connected to my ground bus. Sound legit? Thanks for the info btw. Sent from my E6782 using Tapatalk

Here is the house...before and after Sent from my E6782 using Tapatalk

I'm finally getting moving on this. Now I just have to do the crawlspace junction box and connect to the main panel. Sent from my E6782 using Tapatalk

Thank you all for the input. I plan to tackle this next week. I've got a lot of irons in the fire. I will take pics and post. Sent from my E6782 using Tapatalk

Yes, 6/3 w/ground. And yes on bonded at main but not at sub. Sent from my E6782 using Tapatalk

Ok, thank you. I thought I had that wrong. Sent from my E6782 using Tapatalk

Hello all. I am getting ready to run power to my newly constructed garage. When I remodeled the house I roughed in 6/3 nm from the main panel to corner of the crawlspace, which is roughly another 8 feet from the garage. I have a 100a subpanel and plan on a 60a breaker. I plan to splice the...

Just the sheathing and temporary brace for now. I will be blocking them 24oc. Sent from my E6782 using Tapatalk

Day 5...only a half day today, roof sheathing kicked my ***. It's all done except for the peak, I'm just burned out, I'll get at 'er tomorrow. ...I never take a break, we have six kids lol Sent from my E6782 using Tapatalk

Roughly 9', I used 104 5/8" precut studs. Sent from my E6782 using Tapatalk

Day 4...trusses raised and set, tails cut, rat runs, fascia board and gable overhang. Tomorrow, sheet the roof. Sent from my E6782 using Tapatalk

Day 3...housewrap and windows, took it easy today. It was just me today so it was difficult to get the housewrap flat with the wind. I Also figured the angle and cut some 2x's to frame the gable overhang, not exactly sure how I'm going about that yet. Started lifting trusses up. The tails...

One helper, possible rain tonight, hopefully have it weathered in by Thursday Sent from my E6782 using Tapatalk

Btw, I'm an amateur but corner to corner is within 1/8"...win Sent from my E6782 using Tapatalk

Day 2...menards delivery ***** so short story we had to wait on the right materials. Anyways door and window headers and openings done, walls sheathed. It was a bit windy to put trusses up. Tomorrow hopefully housewrap, windows and doors. Tuesday trusses. Sent from my E6782 using Tapatalk

I'm doing window openings as we speak, then I'll sheath the walls and put up trusses. I have a 36x36 and 36x48 slider, any suggestions for height off floor with 9 foot ceilings? Sent from my E6782 using Tapatalk

Yes I have paperwork for the trusses. Yes I have inspections, been dealing with the inspector for quite some time, so we're familiar. Sent from my E6782 using Tapatalk