Search results

Can’t seem to find anything deeper than 12 inch wall cabinets for the garage. I was hoping to have 18 inch deep cabinets, but can’t find them. Any suggestions?

Looking for feedback, I am tired of tire shops.

While i did suggest the streamlight to fit the criteria earlier in thread i actually use my fenix uc35 the most. It has 5 stages of light output and stays in which ever mode you last left it when you turn it on and off. Has a tail button for on/off and a separate mode button. i like this cause i...

Looking at picking up a tire changer and wheel balancer. Tired of wasting time looking for descent used. So my choices are: Mayflower 980 machine with 800 balancer all in for $2400 + tax or Atlas TC221 machine with WB11 balancer for $3100 + tax and possibly a shipping charge I am leaning...

The streamlight 66608 in coyote is 250 lumen about the size of 1.5 (long) aa battery and is rechargable. The coyote one is the only one that turns on to high position on first click. For some reason, the black one turns onto low on first click so you have to click it twice. That is why I bought...

Looking at one for $900. Is it worth it over a brand new mayflower or even atlas 221?

If they are aftermarket I can’t seem to find any drawer liners other than the originals in 29 inch deep.

So after about a year with my used snap on 7022 I have realized that while the box is pretty decent the drawer liners are utter ****! And the biggest problem is that they are so deep I can’t find any drawer liners that would work. These things don’t hold anything in place not even themselves my...

So i went to hobo freight and got a pack of zerks. Took the old straight coupler off my old broken gun and put a 90° zerk on it, i also took the sideways fit coupler and put a straight zerk on it. So essentially I made two of my own 90° couplers.

So it seems to be breaking in a bit. And I was able to get to 9 out of the 11 fittings on my truck. The two on the Pitman arm I’m going to need some sort of 90°. I have a performance tool 90° that I’ll probably go get a zerk fitting for and see if I can make it work without spending anymore money

So i got the k32 delivered today. Put a tube of green grease in and so far so good. Only thing is the tip once locked on does not let go too well. I had to completely unscrew the end so it would release the zerk! I like the lock n lube tip but it seems huge and i already have some tight spots...

Which one? My buddy says lock n lube. But what says you?

Well now i have no skips from t10 -t60 including the t27 & t47 fyi the t27 is very common on harleys

To the guy who said that I’m upset, I posted this to laugh at myself. I am nowhere near upset, this will just fill in another hole in my set. Even if I never use it it’s a funny conversation piece

After some research the only official thing I can find it being useful for it’s for the bolt that holds the tailgate straps on a toyota taco! Lol I know I will never own one because I wouldn’t fit in it! Lol

So to make a very long story short. I needed to do a repair on my truck and one of the bolts was a torx head. The T 30 was too small and the T 40 seemed to be too big so I figured it was a T 35. Not many people make a T 35 torx. So I bought my first tour truck tool and it is a lovely Matco T35...

Again is this a high torque application

Is it a high torque fastener? my craftsman (90s era USA) 32mm is closer to 33 (probably 32.8ish) and 1-1/4 is about 32.5 ish both 1/2 inch drive 12 point

Why don’t you take it off and reinstall the clamp so that the tightening nut is on the right side of the pipe and facing straight up so you can go straight down on it with a regular socket?