Search results

Alright, since everyone wants to play code lawyer here - yes, I know a feeder isn't a branch circuit, thanks for the lecture. Have I said a sub panel can't be used? My bad if I did. The actual requirement is NEC 680.44 (who wants citing, could simply check internet), which says the spa has to be...

@wyliesdiesels NEC Article 680 (Spas & Hot Tubs) says that spa has to be on a dedicated branch circuit. That means the breaker feeds only the spa, without anything else tied in. Even a small loaded garage circuit would be count as a shared feeder and not dedicated. Manufacturer also call this...

Yeah, that's good idea, anything to knock out slime or mold in the line will help keep it clear longer. Just make sure to flush with plenty of hot water after so no cleaner smell drifts into the fridge

I have got a few brand new, OEM DeWalt DCB609 FLEXVOLT 20V/60V MAX 9.0Ah batteries available. ✅ 100% genuine DeWalt ✅ Never used, still fresh stock ✅ Free shipping anywhere in the USA via UPS Ground Price: $140 each (negotiable, so drop me offers) , shipped to your door. Payment: PayPal...

For light duty a good sealer like TS210 will do fine, but if you want max durability against jacks, salt and oil go with Rust Bullet, it is more work up front but tougher long term

Yeah, they'll freeze up if the drain tube stays damp or the little rubber check valve gets dunked. Cleaning it usually solves it, but if ice keeps forming you can run a bit of weed-whacker line through the tube or even slide in a copper wire down from the heater so it transfers a little heat...

If that is the case then you are already set up right. As long as that 60A GFCI is truly a homer just for he tub with its own disconnect, you're good to go :D

Good point sir, lightning/motor contractors are built heavier for that kind of duty. Definite-purpose ones will work, but if you want max lifespan with lots of on/off cycles, a proper lightning contactor is the better call.

Yeah, dedicated means its own homer from the main panel on a GFCI. Feeding it off that old 60A garage line still isn't the same, you would be splitting a feeder. Code wants the spa on its own circuit with nothing else hanging off it, even if the garage only pulls a little

Yeah, use a relay to do the heavy lifting and a nice wall control to trigger it. Here is the setup: - mount a 20A circuit to a small basement panel - install a 30-40A definite-purpose contractor (120V COIL) - Upstairs, use any good-looking in wall timer or some smart switch (most of them are...

Easiest way to snip it off and put on a new 4-pin flat connector. They are pretty cheap and easier than trying to rebuild the old one. Match wire colors and crimp/heat - shrink the new ends and good to go :)

Friend got a similar spa setup and he had to run a dedicated 60A GFCI line just for it. You really don't want to share that old garage feed, code calls for its own circuit and shutoff :/

Drain's clogged - melt water can not reach the pan so it pools and leaks. I would clear the drain hole under the evaporator with hot water or a wire. Not a refrigerant issue :D

I would go with the 120XP if you can swing the price. The pro-series XP versions tend to have thicker handles, beefier internals and are just more durable. They also usually have better tooth count, so ratcheting would be smoother. If you're tight with money or using the ratchet occasionally...

That "Challenger" mark is not the same one Penens/Proto used. This style with the sweeping "C" underlining the word shows up on older hand tools from the early 1900s, usually wood-handled screwdrivers and brace bits. They were more of a hardware/contract brand, not big industrial line like...

If you want one machine to do it all, you'll end up with "okay" results on everything, but not perfect, so depends what you want. For drill bits, a Drill Doctor type sharpener is hard to beat, especially for HSS. Masonry bits are a bit trickier that's why most people just replace them, but a...

42" is pretty common because it keeps benches and toolboxes from blocking them and still gives light. Outlets at 48" would be a smart in a shop I guess because it would be way easier to reach over benches and you don't have cords dragging on the floor. I've heard some guys even go a bit higher...

Check bellow.

Don't use bleach through the pressure washer because it will kill your seals quickly. Pump sprayer to apply a strong mix, wait for 15mins and then hitting it with your washer using plain water would be best option I guess. You can also rent or buy a cheap chemical sprayer wand that will hook to...

Yeah, people do it all the time. Good things - you do not have switches in the way, lights come on as soon as you walk in, super handy with arms full of stuff Bad things - as you said, sensors can time out if you are under a car or working still. Best fix, in my opinion, would be multiple...