Search results

Shooting hasn't worked so far!

I am planning on adding a concrete floor to an existing 32' x 24' unheated pole barn in lower Michigan. The structure is divided half & half with horse stalls and an open 12' x 32' area where the concrete will be added. There are numerous ground hog holes throughout the dirt floor. The new...

Re: Vintage Floor Jacks REES 10 Ton Jack Cast into the back of the jack is the following: NO 21, CAP 10 TONS, LIFT 9 IN, REES JACK, PATENTED, MFG BY ICP CO. PITTSBURG U S A. It weighs 45 Lb. is 14 " tall 23" fully extended. Cast into the jack in three places are the numbers NO 21, 21-1, &...

Good to know. I'm heading North for three months, I'll get back to the lathe after Labor Day. It was assembled onto a heavy board which I still have. I unbolted it to move it into storage.

Thanks, I might consider that, but my recent experiences with shipping heavy objects has been "pay more in shipping than the cost of the object". I'll cross that bridge later on, if I decide to sell it.

No Duct Tape, but I did sacrifice an incandecant Milwaukee flashlight, but added a newer LED model.

Thanks!

Thanks for your input. If I do sell, it would have to be a local pickup, Tampa Fl. "Looks pretty minty", as I said before, he died before he could use it! Here is a sideways picture of the end plate that was requested. Can't seem to rotate the image properly. It is in storage, but when I...

Milwaukee & Black & Decker.

How much do you think this cost new back in the late 60's. $300-400??? This one had the independent three jaw chuck still wrapped in oil paper in the original box when I got it, unfortunatly the chuck was for the next larger size Craftsman lathe, so it would not fit this one. I'm sure my Uncle...

lathe bed to center of spindle 3", overall lenth 32", lathe bed width 4 5/8", lathe bed length 24 7/8", chuck to tail stock approx. 18" To make it easier to move I took it off of the wood base & partially disassembled it when I moved it into storage. I will try to get a picture of the end...

Even more.

More pictures.

Pictures. The manual is a 1900 plus page, 13th edition, copyright 1948.

This was my uncles lathe, he purchase it just prior to his retirement, then before it was ever used, he passed away. When his stuff was distributed I got the lathe. I have always thought that someday I would learn about it but I never did get around to it. Its serial number is 016989. Can you...

Thanks for the advice and website information. It seems like the best place to buy a LM3800 is on the internet (approx. $285 + shipping) the local guys want 150-200% more and that doesn't include installation and door balancing.

After reading a few threads on jackshaft openers, it seams that alot of you guys love the Chamberlain Liftmaster 3800. So, I'm considering the purchase of one for my single 9 foot wide overhead garage door. The problem is that I have raised the rails from the standard height (to accomodate a...

I went in there (Lowes) for something can't remember what now! Came out with this real cool (I think) B&D cordless battery op 18 volt 18 gage brad nailer. My old Devilbis air unit had some broken plastic parts in it & only does 5/8" to 1 5/8" brads. The new B&D does up to 2" with flush & counter...

Nova 65 SS, About a year ago I posted/requested information on doing a high lift on my 9'W 8'H Amarr 5 section garage door. I had raised the conventional opener (ceiling height 11' 4") & raised the horizontal track & extended the verticle track & added longer cables with the existing 5" drums &...

Will the MCT302 work with an existing wired system? In their specs. they only mention 2 wired zones and 28 wireless zones. Sounds like I would have to convert a bunch of my wired zones to wireless to use their system??? Thanks for the feedback.