Search results

One more update... so I decided to watch Craigslist for a cheap used portable, rather than buying another (expensive) new one. They were hard to find during the 100 degree days, but we had a break in the heat for a week and I grabbed one for $75. I finally got around to cutting the hole in my...

Just an update... I used it one day for about 3 hours. It was ~90F outside, and there were about 10 of us hanging out in the garage. The A/C seemed to keep up just fine... it was very comfortable in there. I just left the man door cracked, with an aluminum flex hose blowing the hot air...

Ah... that looks really nice, thanks for posting that pic! Yeah, I was thinking about that, and noticed that the one I picked up has a port for an inlet hose, but no actual hose (so it just draws the inside air). I guess the problem is getting enough seperation that you're sucking in outside...

My garage gets hot, but not usually unbearable. It's north facing, attached, and fairly insulated. My 12000 BTU heater worked REALLY well this winter, so I figured comparable cooling should work pretty well too. You're probably right, a dryer vent really wouldn't be a big deal. That's a...

So... I picked up a portable A/C that I plan to use in my attached 2 car garage when I'm working out there during the summer ( http://www.sharpusa.com/ForHome/HomeEnvironment/AirConditioners/CV2P10SC.aspx ). A typical installation vents it out a window, but being a garage, I don't have any sort...

Woohoo! Less than a year from thread start to finish. :) The install went smoothly, and it works great. Cutting the torsion bar was no problem, and I just cut a hole in the drywall to give me a little more room on the other side, then filled it with an old work ceiling box (to keep air drafts...

Awesome... thanks for the quick reply. I'll just cut it enough to make it fit... not any less than 1" from the bearing plate. I definitely won't be unwinding any springs... never done that before, and it's probably dangerous for the inexperienced... plus both sides have too much bar sticking...

I'm finally getting to this project... the 3800 arrived today, so I started looking at it and figuring out what I need to do. Quick question though... is it okay to cut off the end of the torsion bar? The manual says I need 8" between the wall and end of torsion bar... and that the torsion bar...

Assuming this is like most things I deal with that can be converted to work with various voltages... inside the pump there is a transformer. Lets say that the pump runs internally from 24V. So, to get from 120V to 24V, they have a transformer that scales the voltage down 5x (but in turn...

Nope, not knocking them... they are really fun cars... just poking fun at how light they are, compared to some of the heavy cars that many of us have. Your 78 Pro street Camaro weighs what... the same as 2 Miatas? ;) Costco looks like a good deal... Northern Tool has them for $2k w/ free...

Yeah, but that car weighs what... 45 lbs? ;) Heh, but I agree... this thing is great. I just replaced the rear brakes on my minivan last night and it had no problem lifting, holding, and lowering... and it made the job so much easier. And since the van needs all the room it can get, the pump...

Interesting... I hadn't seen that one before. It looks to be a little more expensive, and I think I'd need to buy quite a few accessories for it (I don't think it comes w/ remotes, or a receiver for remotes... or even a wall button), but I'll definitely consider that. I've gotta see if my...

Nice... thanks! So really, I just need to get my hands on one of these and see what I can do with it. Pat

Yeah, I saw a couple of you guys do that... definitely a good idea, and I'll probably end up grabbing a bungee to do the same once I get sick of holding it. So far, it hasn't been a big deal to me to hold the lever while lowering though. It seems safer as I'm standing out of the way, and can...

Kevro: Thanks a ton... that's extremely helpful. I'll have to get my hands on one of these and see what I can make out of it. Thanks! Pat

The other side of the wall is the front porch (exterior), and if I needed to, I could use the other side of the garage door, which is the side of my house... so they're both exterior walls. I'll have to see if making the pocket is possible. Yeah, above the door there's plenty of room... the...

Hey, So I'm looking to get a jackshaft opener for my garage door, but my garage is a little narrow, and there's not much room on the sides of the door for the opener. Looking at the Liftmaster 3800 manual, it says it needs 8" between the wall and end of torsion bar. I only have about 5.5"...

Thanks... the ceiling is about 10'3" (except for one beam going across), but it was too short for most regular lifts, and the portability of the Maxjax made me decide to go for it. The garage door actually doesn't affect the lift when it's closed (the opener and rails are outside the lifting...

Here's some pics of my install... you can see the pump mounted on the wall, the mounting/routing of the hoses, and rest of the mess in the garage ;) . I used the hooks in places where there was some pressure of a turn (they're strong), and the clips to hold it in place (pretty weak, but keep it...

Yeah, I love the Maxjax... and with this mod, the floor and work area is even more open. It used to be a little tight for me w/ the workbench, pump, and hoses while a car was up on the lift, but it's great now. Well worth the minor added cost and time to do. IMO, Dannmar should sell a...