Search results

Dewalt DCF787 20V Cordless 1/4" Brushless Impact Driver 20 Volt MAX Lithium Ion for $55, free ship. This is a Ebay deal but the vendor has solid feedback and keep in mind warranty is probably a non-warranty.

I have one I use on my miter saw a few times per year, it is great to support long pieces and fine tune cuts by easily moving the wood a fraction one way or another to the cut line.

Woot is affiliated with Amazon so posting here. Free ship if you have Prime. BORA Adjustable Roller Stand 2-Pack for Table Saw Extension Roller $32.99 https://tools.woot.com/offers/bora-adjustable-roller-stand-2-pack-0

$79 for a drill & driver & battery and charger. CRAFTSMAN V20 20-volt 2 -Tool Power Tool Combo Kit ( 1 -Batteries Included and Charger Included ) Item #1248745 | Model #CMCK201D1 https://www.lowes.com/pd/CRAFTSMAN-V20/5017892173? Cross posted from the Craftsman V20 Deals

$79 for a drill & driver & battery and charger. CRAFTSMAN V20 20-volt 2 -Tool Power Tool Combo Kit ( 1 -Batteries Included and Charger Included ) Item #1248745 | Model #CMCK201D1 https://www.lowes.com/pd/CRAFTSMAN-V20/5017892173?

The problem has been solved, I was loading it incorrectly. I did not pay close attention, did a quick read of the manual the other day when it arrived, it all seemed very straightforward. I released the magazine catch, pulled the magazine out, and it appeared you load from the back, the staples...

Thanks to all for the comments. I will take a fresh look in the morning. I was dead tired when I was trouble shooting, never a good idea trying to solve a problem when you are dead tired.

Senco (new) Staple Gun Woes, issue fixed Hello to all, I just purchased a Senco SL150MG, a basic 18 Gauge 1/4" air stapler. The tool will not drive a single staple. I am at a total loss and hope someone has some suggestions. I have the tool hooked up to a Porter Cable air compressor which I...

Thanks to all who commented. Went with Senco. It will be a good addition to the shop for many future projects once the current project is done.

Good day to all, I am putting up a picket fence, a lightweight garden fence, wife says no screws, no nail heads! At a former residence, I tore down an existing picket fence that had the pickets attached with staples, amazingly it was rock solid and the pickets were surprisingly very difficult...

After taking a look at about six cuts (all I made initially), they definitely are not clean cuts, you can see the blade climbed or dipped throughout the cut. I am going to keep the saw for cutting up pallets and other work where accuracy is not critical and I am going to buy a good saw, probably...

Thanks for all the input, will ditch the jig and cut using speed square lines for a guide. Think I found the issue, from a user review (at sears website) of the exact saw I am using; For some reason, the shoe on this saw is mounted to the blade guard Instead of the main body of the saw, so its...

Interesting, I could have been lifting, saw a little burning on the wood after the cut was done and it basically looked normal. The shoe of the circular saw rode on the jig and I was trying to make sure the opposite side of the shoe (top of cut) remained flush against the 4 x 4 timber so I...

So as an update I cut a number of post and it went OK for the most part. I have used a circular saw before, just never to cut 4 x 4 post set in concrete. I first made a test cut using my jig (basically 3/4 ply screwed/glued that fits around 3 sides of the fence post). I cut high on a post just...

Thanks for all the comments. Just wanted to make sure I wasn't missing an obvious better way to do this, going to cut and let them fall.

Best way to cut PT 4 X 4 fence post w/circular saw (Update Issues) Hello guys, I am putting up a privacy fence in the backyard and getting ready to cut about 40 pressure treated 4 x 4 (3.5 actual). I am using a circular saw, put in a new blade already. They are in concrete already and I am...

Thanks for posting, better that I expected. Have you shot anything in SD? I like the feature of just letting it record, like if you were going to be gone for a couple weeks. Using HD the card would fill up too fast.

Thanks Op, interesting. Saw this in the FAQ's, The WyzeCam’s frame rate is 10 fps for both HD and SD video modes. This does not excite me.

Actually I did not cancel. I went to Lowes website after waiting a couple weeks, you can enter your order # for status and it showed canceled, oddly, I received no email notification of being canceled. ETA: Went back into the Lowes website, just to grab a screen shot, now shows; The...

The last two Irwin orders I placed, great price, showed in stock, paid for shipping, got a confirmation email, neither order was delivered. Both canceled after about 10 days of waiting for the product.