27' x 25' ish Garage addition
- Thread starter kgc10
- Start date
Crazy Backyard Builder
Well-known member
Looking great, any updates ?
blazentrout
Well-known member
I really like how you are bringing it together.
Here is a up date on the project. My wife picked out the outdoor lights for the shop I installed 3 of them on the front.
I have also built a loft in what was the space in between the two building. I removed all the stucco that was once on the out side of the new garage
Here is a shot from one end of the shop looking at the far corner.
My project for the weekend was to start the electrical in my equipment corner. I didn't want to drill a bunch of holes in the studs and getting the wire around the corners was not going to be fun. I purchased 40' of Wiremold, at one end the Wiremold goes under the 200amp sub panel that will feed all my equipment and the other end needs to cover a 2'' conduit that comes from the 400amp main panel that will feed my Miller Synrowave 350.
I have also built a loft in what was the space in between the two building. I removed all the stucco that was once on the out side of the new garage
Here is a shot from one end of the shop looking at the far corner.
My project for the weekend was to start the electrical in my equipment corner. I didn't want to drill a bunch of holes in the studs and getting the wire around the corners was not going to be fun. I purchased 40' of Wiremold, at one end the Wiremold goes under the 200amp sub panel that will feed all my equipment and the other end needs to cover a 2'' conduit that comes from the 400amp main panel that will feed my Miller Synrowave 350.
It's been a while but a small update a lot of what I'm doing came from other builds so thanks.
I hung my engine stand to maintain floor space.
I've slowly insulated and installed plywood to a couple of the walls.
I picked up a new compressor two weeks ago. I'ts a Quincy 7hr 60 gallon
I hung my engine stand to maintain floor space.
I've slowly insulated and installed plywood to a couple of the walls.
I picked up a new compressor two weeks ago. I'ts a Quincy 7hr 60 gallon
it's been a little more than 3 years from my last post and i would like to say the shop is done buts it's not but its almost there. New power pole flying in it will have a 50 KVA transformer and with the 500's coming out of my 400 amp meter and the 4/0 service I have power.
[/url]20141001_141550 by Ralph Kenyon, on Flickr[/IMG]
[/url]20141001_170019 by Ralph Kenyon, on Flickr[/IMG]
My air compressor room with dust collection for the bead blast cabinet.
[/url]20151226_182829 by Ralph Kenyon, on Flickr[/IMG]
[/url]20160103_191735 by Ralph Kenyon, on Flickr[/IMG]
[/url]20160522_212317 by Ralph Kenyon, on Flickr[/IMG]
I love free stuff, free and full of hardware.
[/url]20160522_212548 by Ralph Kenyon, on Flickr[/IMG]
I made a drill, driver, rattlegun holder
[/url]20170102_175543 by Ralph Kenyon, on Flickr[/IMG]
[/url]20170102_180351 by Ralph Kenyon, on Flickr[/IMG]
My air compressor room with dust collection for the bead blast cabinet.
I love free stuff, free and full of hardware.
I made a drill, driver, rattlegun holder
Collecting parts
[/url]20161125_160259 by Ralph Kenyon, on Flickr[/IMG]
Finally got my lift.
[/url]20160530_203706 by Ralph Kenyon, on Flickr[/IMG]
20160528_200653 by Ralph Kenyon, on Flickr
Finally got my lift.
20160528_200653 by Ralph Kenyon, on FlickrHeat and A.C. going in.
[/url]20180210_190224 by Ralph Kenyon, on Flickr[/IMG]
[/url]20180203_143929 by Ralph Kenyon, on Flickr[/IMG]
[/url]20180203_144104 by Ralph Kenyon, on Flickr[/IMG]
20180214_200143 by Ralph Kenyon, on Flickr
20180214_200143 by Ralph Kenyon, on FlickrHere are some SO cord supports for the lathe and the welder when it comes out the Wiremold.
[/url]20170904_123655 by Ralph Kenyon, on Flickr[/IMG]
20150702_201432 by Ralph Kenyon, on Flickr
20150702_201432 by Ralph Kenyon, on Flickr