30' Enclosed trailer build

[Glammers37]

My Sons and I started this project about 2-1/2 yrs ago and are finally just about done. we built this to haul around my youngest sons dirt modified. we had built several open trailers, but this is the 1st enclosed we have built. I will post a few pics as I get time. we built this totally from scratch. 2" x 6" tubing for the frame, 1-1/2" x 2" tubing for the walls and roof bows. we had it totally spray foam insulated and installed roof A\C and an RV Furnace.
Big Job! almost thought a couple of times we bit off more than we could chew but we got thru it. It will be fun to finally get to use it.

 

[Case IH]

WOW, that is very impressive, I wouldn't of known where to start with a covered trailer!....it really sous look professional!!

 

[aabirdman]

I've been contemplating this my self. More Info and pics would be a great help.

 

[HMCFab9]

Looks great! Very nice with the sprayfoam!
Would you do another one, or would you buy one done? Just curious.

 

[madosta]

Awesome job. I would never think to do this myself, but we need MORE PICTURES!! PLZ!

MOAR PICS!

 

[kluckfab]

Damn! Get some more and bigger photos, looks great

 

[Glammers37]

I would do another one, maybe a gooseneck with a stacker. I'll try and put some more pics up.

 

[Glammers37]

Here's a picture of the ramp door frame. I have a pic of the frame on the Jig, but it won't upload.

 

[ADSR]

open a photobucket account and get them pics loaded!!!

nice work on the trailer!

 

[Glammers37]

Some cabinet pics. Made from 1" aluminum square tube and .040 aluminum sheet

 

[Glammers37]

Another cabinet picture. Toolbox is just a lower tool cab from menards.built in.

 

[Glammers37]

Close up picture of cabinet face frame detail. If I was to make these again I would make the fit a lot looser. It's hard to fit these w hen the tolerance is so tight. Looks nice though with tight fit and finish,

 

[Glammers37]

Sorry forgot pic in last post

 

[Case IH]

Wow this entire thing looks great! I wish I had the ability to do this!

 

[Big-Foot]

Nice job!!!!

Wherebouts you guys located?

 

[Glammers37]

Owatonna, not to far away from you

 

[Big-Foot]

Looks like a darned nice and strong trailer. Reminds me of the trailers Lance Mathees builds over in Winona.
Where do you guys race at?

 

[Glammers37]

Thanks. I hope it pulls ok. we pulled it to our other shop once before we sheeted the sides, and it seemed to pull fine. we are thinking of building a toter to pull it now. we primarily race a Wissota B mod and a pure stock @ Chateau, Deer Creek, Kasson. ( if they ever race again)+ few specials

 

[Big-Foot]

Hoping to get to some of the tracks down here this summer.. It's been ages for me... I used to crew Wissota Late Model out of Cedar Lake for a LOT of years..

 

[Glammers37]

Here's a pic of the cabinet door frame corner detail. Cut corner pieces from 1-1/2" aluminum angle. And then used 3/16" countersunk rivets. Door. Frames are 3/4" extruded alum, we decided to polish them. It was quite a process because the material was anodized. The frames have a 5/8" inside width so we used 1/2" closed cell foam and then glued .040 white aluminum to each side. It fit inside perfect.

 

[Glammers37]

Another pic of corner detail.

 

[kald]

Whats up with the one picture a week?

 

[Glammers37]

Sorry, been super busy trying to finish this trailer and getting two race cars ready for the season. Plus work two jobs!