Woody610nb
Banned
Any suggestions where I can purchase metal roofing for my barn near Concord, NC. I looked on line, but it seems that there are very limited choices. Does it pay to have it shipped in, seems like it would be expensive.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an alternative browser.
You should upgrade or use an alternative browser.
Buying metal roofing.
- Thread starter Woody610nb
- Start date
stingry
Well-known member
d110pickup
Well-known member
I bought mine at Back Home Metal Roofing in Grayson, Ga. That's NE of Atlanta. There is probably a similar place closer to you.
https://www.facebook.com/BackHomeMetalRoofing
The advantage of buying from them over HD is you give them your measurements and it's all cut to length. You're not buying any extra material and you don't have to make any cuts.
Also a much better selection of thickness & pattern. I did the ceiling of my shop in a thinner gauge than the roof of the portico out back.
Look towards the end of my build thread for photos.
Mike
https://www.facebook.com/BackHomeMetalRoofing
The advantage of buying from them over HD is you give them your measurements and it's all cut to length. You're not buying any extra material and you don't have to make any cuts.
Also a much better selection of thickness & pattern. I did the ceiling of my shop in a thinner gauge than the roof of the portico out back.
Look towards the end of my build thread for photos.
Mike
stingry
Well-known member
I bought mine at Back Home Metal Roofing in Grayson, Ga. That's NE of Atlanta. There is probably a similar place closer to you.
https://www.facebook.com/BackHomeMetalRoofing
The advantage of buying from them over HD is you give them your measurements and it's all cut to length. You're not buying any extra material and you don't have to make any cuts.
Also a much better selection of thickness & pattern. I did the ceiling of my shop in a thinner gauge than the roof of the portico out back.
Look towards the end of my build thread for photos.
Mike
My local HD also offers this service if you order the material. I'm not pushing Home Depot, just giving the OP some options.
Cheers
Steve
Riverside
Well-known member
ctgoodman
Well-known member
You might try Mid-State metals:
http://midstatemetals.com/
They are in Cleveland, NC so not too far away from Concord. Only about 35 miles or so.
http://maps.google.com/maps?ll=35.7...ient=embed&q=2415 Rary Rd Cleveland, NC 27013
Shipping probably will be expensive since it most likely have to come in on a semi and trailer. Shipping would easily be in the several hundred $$$ range.
http://midstatemetals.com/
They are in Cleveland, NC so not too far away from Concord. Only about 35 miles or so.
http://maps.google.com/maps?ll=35.7...ient=embed&q=2415 Rary Rd Cleveland, NC 27013
Shipping probably will be expensive since it most likely have to come in on a semi and trailer. Shipping would easily be in the several hundred $$$ range.
Last edited:
OP
Woody610nb
Banned
Thanks for the replies; Thanks ctgoodman, midstate looks good and is close by.
Last edited:
Beemer533
Well-known member
I think mid-state is where I got quotes from a couple years ago when I was looking at re-doing my roof with metal.
Their prices were very reasonable as I recall and they sent me several free sample for me to look at.
Their prices were very reasonable as I recall and they sent me several free sample for me to look at.
gtripleb
New member
Lowes sells Union Corrugating brand. The last time I ordered metal roofing from Lowes, which was about 4 or 5 months ago, I ordered 2 sheets and they sent 3 with one of the sheets being used as a protection sheet. I was kind of surprised when I went to Lowes and picked it up. The sheet was a little bent where the bands came across the sheet but nothing I couldn't bend back. I don't know if other manufactures do that or not. Price at the time was around $2.00 per foot in length.