Central Pneumatic HF air compressor

[dorksterr]

I was wondering if anyone had any experience with the Central Pneumatic air compressor. It is on sale for $99 at HF. The model number is 95386/67501.


I really am only looking at getting an air compressor to flush out my irrigation system before each winter. The local guys charge $60 to come out and flush it. The last time they did it, the guy showed me how everything was done and it looked really easy. I figured if I could get one for under $120 the compressor would pay for itself in two years.

Any thoughts? Thanks!!

 

[fatboyf150]

It's not a bad compressor. We sell quite a few and I have only seen 2 come back. If you can wait, that compressor will be $99.99 on our parking lot sale on march 11, 12, and 13th.

Edit - Just reread your post. Do you have a coupon for this compressor? It's on sale price is $119.99 HFT online ad


(parking lot sale ad will be up in a little bit, got to scan all of it)

 

[diesel research]

2 years is a good ROI for most purchases.

 

[Kev442]

Told a friend of mine to quit screwing around with his antique death trap compressor that could not get over 65psi and buy one of these. He says it runs just fine and was well worth the $89 he spent back then.

 

[dorksterr]

fatboyf150.

I have the sale coupon for $99 bucks. Do you think it would have enough power to run say a few air tools like a 3/8 impact and 3/8 ratchet? I wouldn't need to use them much just for a brake job or small mechanical repairs.

Thanks,

 

[fatboyf150]

it should be fine.

 

[JASTECH]

dorksterr, I would reccomend installing the LPHV connectors which will give your tools a boost and work well with that unit.

Thanks, JASTECH

 

[X1 Mike]

dorksterr, I would reccomend installing the LPHV connectors which will give your tools a boost and work well with that unit.

Thanks, JASTECH

Don't be dropping that LPHV stuff on us without educating us. What are they and what do they do? I would like a little boost for my air tools, I know my compressor is the weak link right now.

 

[diesel research]

fatboyf150.

I have the sale coupon for $99 bucks. Do you think it would have enough power to run say a few air tools like a 3/8 impact and 3/8 ratchet? I wouldn't need to use them much just for a brake job or small mechanical repairs.

Thanks,

Now you are changing the game LOL. If the compressor was simply used as originally stated, you would get your bang for buck quickly.

Now placing it in a more demanding situation, the results may be different.

From the description

Affordable and portable air supply for powering nailers, general shop clean-up, airing tires and inflating sports equipment

Inflating a basketball is a good bit different than knocking off a set of lugs.

Might be better to look into something bigger. You have already added a few uses to the list, and may be tempted to try to add a few more...

 

[diesel research]

Don't be dropping that LPHV stuff on us without educating us. What are they and what do they do? I would like a little boost for my air tools, I know my compressor is the weak link right now.

HVLP fittings are bored out versions. Thinner walls/more fragile, but more air flow as well.

The same could be said about quality air lines.

 

[LEVE]

I paid $30 for one (NIB) last year at a Discount Store. It was "Blowing the breaker"... I took a chance and it's been running fine ever since. Not a bad little compressor and at the price, it's a throw-away if it breaks.

 

[X1 Mike]

HVLP fittings are bored out versions. Thinner walls/more fragile, but more air flow as well.

The same could be said about quality air lines.

Ok well I just have standard fittings which I've always assumed were the choke points, what are the best brands and where do I buy them?

 

[Kev442]

fatboyf150.

I have the sale coupon for $99 bucks. Do you think it would have enough power to run say a few air tools like a 3/8 impact and 3/8 ratchet? I wouldn't need to use them much just for a brake job or small mechanical repairs.

Thanks,

I used a 11 gallon 2 HP CH compressor for years with a 1/2" impact on tires. You will wait a little on the well torqued lug nuts but it's not super annoying. It ran my framing nailer all day long too. Don't even consider cutoff wheels, small sand blasters, etc.

 

[fatboyf150]

Ok well I just have standard fittings which I've always assumed were the choke points, what are the best brands and where do I buy them?

http://www.harborfreight.com/2-piece-brass-hi-flo-female-air-coupler-set-97631.html

http://www.harborfreight.com/2-piece-brass-hi-flo-male-coupler-set-65180.html

http://www.harborfreight.com/4-piece-hi-flo-male-plug-set-65894.html

 

[chewy7]

you are better off getting some milton v series couplers for like a dollar or 2 more. harbor freight couplers are junk!

 

[TAMPAGT07]

It is what it is, a $100 compressor. Years ago, I picked up a used Craftsman compressor for $100 off of CL. Did it do the job? Someitmes it did. Was I happy with it? No..It ran some of my tools, but could not run them all. I plan on adding a sandblast cabinet down the road, so when I replaced it, I made sure to get compressor to fit my needs. I watched Craigslist religiously for like six months before buying my IR 60 gal, 5hp compressor (13.5 cfm). It has a brand new motor and pump, for $350..I wouldn't settle for less, but I know what I will use it for..Just plan ahead a little..Will this compressor meet your future needs..If it will, then go for it..

 

[dorksterr]

Thanks for all of the replies. I am still tempted to get it but I may just wait a little longer to see if something else is out there.

So are there any recommendations as to what compressor rI should get? I'm not a pro mechanic by an stretch of the imagination. I have a home garage and do things like change brakes, some suspension work, alternators, water pumps and small things. I'm looking for something that may be able to run an air ratchet for short burst. I already have a snap on 1/2" impact for things like lug nuts but wouldn't mind being able to run a smaller 3/8 air impact.

What size should I be looking for? Is there a certain air flow rate?

Thanks,

 

[TAMPAGT07]

What size should I be looking for? Is there a certain air flow rate?

Thanks,

I would sit down and ask yourself what tools you will be using now and in the future. Mine is rated at 13.5 CFM which will meet all of my needs, including a blast cabinet. Even some small tools like grinders will use a lot of air. Search around the net and see what requirements are needed for what tools you wish to purchase. Keep in mind that a Craftsman 5 hp probably not as powerful as an ingersol rand (Century) 5 hp motor..I would also stay away from $300 60 gal compressor's from sears,HF, lowes. But that's just me. I waited till I found what I wanted for like 1/3 the price of a new unit...I hope this helps..