Epoxy Estimate

[Dominico]

Thanks to you guy's, I have been doing a ton of research on options regarding what type of product to use on my garage floor as well as whether or not to attempt it myself. I decided to get an estimate from a "long time reputable contractor" in my area and then make my decision from there. I have a couple friends who have had this contractor do their floors and they are very pleased.

The estimate for a 24x26 floor came back at $1700 this encompassed shot blasting,filling expansion joints and applying a solid color epoxy, including 4-6" of block around the perimeter. I'm undecided on the flakes? The floor is about 18 yrs old and in good condition. It has some shallow pitting from road salt a couple hairline cracks and a few chips around the expansion joints.

I usually do most everything myself, however I have read many horror stories as well as successful ones on this site and I now my limitations. Is this a good price? What would it cost me to do it myself with a professional product? Is it worth the aggravation? Any advice or comments would be appreciated.

 

[Will S.]

You will need to provide more information about exactly what product they will use. A "solid color epoxy" could be anything from a very cheap product from a box-store, to a top of the line product like Wolverine. Will it be clear-coated, as well? Just a guess, but for that price, it sounds like they will be usingsomething like the water-based Rustoleum product.

 

[AlphaGarage]

"Is this a good price? "

It really is impossible to say. That quote sounds in the ballpark in that it's not too low, but it's pretty close to being too low. He might be using a somewhat lower priced material. Find out exactly the coatings that he uses, and their finished depths. And is he using a dedicated primer? That's where most systems fail, lifting at the concrete and that first coating. On the lus side he has good referrals, people you trust, that says a lot.

What would it cost me to do it myself with a professional product?

For your floor the materials we'd recommend would be; 3 gallons of BondTite 1101 as the primer; 6 gallons of LiquaTile 1184 as the body coat, and 1.875 gallons of EnduraShield 2254 as the clear coat, total they'd be $985. The final dry coat thickness would be around 27.4 mils, not factoring in waste.

You'd need a few more items, $150 or so.

Properly applied your job would meet or exceed the contractors results. You would most likely enjoy better materials, and if you take your time and follow the guidelines your end of the project will match their work.


Is it worth the aggravation?

There will be moments as you're doing it when you'll question your wisdom, but there will be years of satisfaction after that clear coat cures when you know you made the best choice.

 

[garagedude]

I don't know what product they are using, but assuming it is a good grade industrial coating, the price they offer is very competitive - actually on the low side. (Your at $2.72 per sq ft. which is unseen in my market)

I would want to know what product they are using to venture any further opinions.

 

[nate379]

Cost me around $350 all said and done to do my floor, same exact size. $2000 price tag you are getting close to the cost of the slab!

I usually do most everything myself, however I have read many horror stories as well as successful ones on this site and I now my limitations. Is this a good price? What would it cost me to do it myself with a professional product? Is it worth the aggravation? Any advice or comments would be appreciated.

 

[Dominico]

Thanks for the prompt reply s to my questions. One important thing I didn't mention is the guy who gave me the quote works for a company that does industrial floors only (no residential work). The contractor he works for has done floors and defined walkways at the steel mill where I work. Through my investigation I found out that a few of my coworkers had their floors done and were pleased with the results.

When I called the main company for an estimate the owner informed me that they do not do residential work however he gave me his employees name and said to call him. He would be fair on his price. The guy rents the equipment from his employer as well as purchases their product so he uses all the same material and tools. When he came to my house he gave me some referrals (my friends from work).

I will find out more specifics on the exact product and report my findings to you guy's for your two cents. I want to take my time and do it right the first time. I don't mind paying for a good product but I don't want to be taken advantage of either. Thanks again!

 

[AlphaGarage]

If the guy is using decent stuff - you're getting a pretty good deal. I think that the fact that you have friends who are happy with his work and materials is apretty good indication that you'll be pleased also. Pull the trigger and enjoy!

 

[Dominico]

Thanks for everyone's input. I decided to "pull the trigger" the job is tentatively scheduled for this weekend. Will post pics when finished.

 

[torquet]

View media item 4870
Just got my garage done for $2.85/square foot. Shot blasting, epoxy and clear coat.

 

[HMEN]

men that looks good