Found a deal on craigslist? - List Here!

[larryq]

10 HP IR compressor for sale in Windsor, CA. $300. "Almost new"

http://sfbay.craigslist.org/nby/tls/5367620004.html

 

[ogorir]

Machine shop closing near Detroit:
https://detroit.craigslist.org/mcb/tls/5375368589.html
https://detroit.craigslist.org/mcb/tls/5375346189.html
https://detroit.craigslist.org/mcb/tls/5375324575.html

I posted in the hot deals section before I saw this sticky, guess I was just excited. I hope someone gets some of this stuff before the crusher.

 

[bl00]

https://altoona.craigslist.org/tls/5379021442.html

Neat old crane for $150 if you have the space.

 

[larryq]

$10 Korean war era toolbox in San Jose CA. Not exactly a new KRL but for $10 looks pretty nice.

http://sfbay.craigslist.org/sby/tls/5379954750.html

 

[donniewilkins3]

I got a Free Lista toolbox. Been in a flood and has some rust.


Sent from my iPhone using Tapatalk

 

[jzt]

That's great, you ****! But this is not the thread to post that.

 

[Bored&Stroked]

That Lista will be a nice restoration project

 

[rednotch]

https://southjersey.craigslist.org/tls/5384955386.html

HF red 5 drawer cart for $125 obo

 

[bennymic]

Two Stage Air compressor 175 psi - $450 (Fairfax)

This is a Sears two stage air compressor. The Furnas controller is set to start at 150 psi and shut off at 175 psi.
The Marathon motor operates at 230-240 volt, single phase. It draws 21 amps. 1750 rpm.
Operates on a 2 pole, 30 amp circuit breaker.
The assembly is Sears Model 102-17316 7/84. Serial # 951431.
The compressor is Model 335, serial # 951431
The compressor is 60" long, 44" high to the top of the air filter and 22" wide.
It sits on a base made of 4"x4" pressure treated lumber on lockable casters.
The base is 54" long, 9"high, 29" wide.
It is equipped with 25" of stranded #10 copper wire I used just to get it going.
It has a belt guard, just not shown. I do not have the sheet metal screws to secure it, but it doesn't look hard.
There are also two air separators and some miscellaneous fittings.
This is big, heavy and awkward.
You will need three other strong men to load this onto a low trailer.
I bought this for a car project that never materialized. Now I don't need it and don't have room for it.
Cash only.

 

[larryq]

What I'm guessing is a 2 stage 60 gallon compressor in like new condition (14.5 cfm @ 90 psi) for $600 in Santa Cruz CA:

http://sfbay.craigslist.org/scz/tls/5385064170.html

 

[kellykungfu]

Hey Everyone,

Here is a free radial arm saw in San Francisco that I have posted. I have had the worst response and luck trying to sell it, from people that wanted me to deliver, etc.

I rather have it go to one of the members here than to get rid of it at the dump.

http://sfbay.craigslist.org/sfc/zip/5386568708.html

 

[firworks]

Is this one of the "Craftsman Block Grinder"s people go nuts for?
craftsman grinder with stand - $50 (peoria)
http://peoria.craigslist.org/tls/5385930862.html

 

[Kaervak]

Is this one of the "Craftsman Block Grinder"s people go nuts for?
craftsman grinder with stand - $50 (peoria)
http://peoria.craigslist.org/tls/5385930862.html

Yes it is and that is a great price for that grinder on the original stand. Go buy it, now. Even if you don't need it, buy it. The stand alone is $100+

 

[firworks]

Yes it is and that is a great price for that grinder on the original stand. Go buy it, now. Even if you don't need it, buy it. The stand alone is $100+

Wow well that's pretty clear. I sent the guy an email. I'll text him tomorrow morning if I don't hear back. I'll probably have to take it off the stand to get it in my car.

 

[KLO101489]

San Francisco Bay Area. Huge heavy duty Sipp drill press. Looks to be from the early 1900's. Only $100. Wish I had the room, but don't so I'm passing it on.

https://sfbay.craigslist.org/eby/tls/5386311882.html

 

[firworks]

Dang. Missed that grinder, he didn't respond and now the listing is deleted.

 

[lilcraigford]

This one might interest the Snap On aficionados:

Snap On screwdriver handles - $15 (Scarborough)

 

[larryq]

Nice looking 1/2 HP block grinder in San Pablo / Pinole CA for $50, includes a lamp.

http://sfbay.craigslist.org/eby/tls/5387306024.html

 

[larryq]

3 inch Starrett / Athol vise (USA) for $45 in Livermore CA. I have the 4.5" version and it's great, 60,000 PSI casting and tough as nails.

http://sfbay.craigslist.org/eby/tls/5387928520.html

 

[_SLY_]

3 inch Starrett / Athol vise (USA) for $45 in Livermore CA. I have the 4.5" version and it's great, 60,000 PSI casting and tough as nails.

Jumped on that. Thanks for posting.

 

[firworks]

"Columbian 4" Vice" - $25 (Muscatine)
http://quadcities.craigslist.org/tls/5389597743.html

Seems like a good deal to me? Anyone near Quad Cities that wants to check er out?

 

[larryq]

"Columbian 4" Vice" - $25 (Muscatine)
http://quadcities.craigslist.org/tls/5389597743.html

Seems like a good deal to me? Anyone near Quad Cities that wants to check er out?

That was a great deal, and appears to have been snarfed up; thanks for posting.

 

[St-rider]

Seems like a nice Snap On taco cart.

https://pittsburgh.craigslist.org/tls/5297711198.html

 

[larryq]

Jumped on that. Thanks for posting.

Glad to hear! If you get the chance, put up a thread in the general tools board with pics and impressions-- those Athol / Starretts are nice.

 

[Journaler]

Seems like a nice Snap On taco cart.

https://pittsburgh.craigslist.org/tls/5297711198.html

I've been looking for one of those for a long time. Wish it was closer.

 

[_SLY_]

Glad to hear! If you get the chance, put up a thread in the general tools board with pics and impressions-- those Athol / Starretts are nice.

I wound up getting beat to it! Too bad, too. I was pretty pumped for the find.

 

[bennymic]

no 3b abrasive machine tool co. surface grinder - $500 (southern md)

8" x 24" table
8" x 5/8" wheel

Could be a deal if not too clapped out.

 

[ineedtools]

Wheel on that is small, ones I've seen all had 12"+ that were 1.5" wide

 

[larryq]

Here's a Milwaukee / Delta 1/2 HP drill press for sale in San Rafael, CA. $100:

http://sfbay.craigslist.org/nby/tls/5392449862.html

"Retired contractor selling tools. This is a drill press and full height stand that probably dates back to the early 1950's when these tools were better made. It has an attached utility work light for precision work and multiple drill speed options. It was made by Rockwell Manufacturing with a 1/2 HP 120 volt Delta motor."

 

[Tucker99]

subscribed

 

[anodyne33]

Cornwell bottom about an hour outside of Pgh. $200

http://pittsburgh.craigslist.org/tls/5393024619.html

 

[ineedtools]

well that didn't last long, was about to hop in the truck and go get it!

 

[rednotch]

US General tool box - $60 its a red cart, figures after I buy one they pop up everywhere used now.

https://southjersey.craigslist.org/tls/5393960877.html

 

[I Love Grits]

Dallas, TX - Champion Compressor 2 stage 5 HP $250 - Negotiable. Says to be in working condition.

https://dallas.craigslist.org/mdf/tls/5394149345.html

 

[I Love Grits]

Dallas, TX - Saylor Beall Compressor.

$450 FIRM isn't a screaming deal given it looks like it's been used pretty hard. But for a single phase Saylor I would pick it up if I didn't already have one.

It's been on there for about a week or so. Could probably get it for $400 if it stays much longer.

https://dallas.craigslist.org/sdf/tls/5383365897.html

 

[anodyne33]

well that didn't last long, was about to hop in the truck and go get it!

D'oh! It wasn't up for long when I posted either.

 

[larryq]

Holland USA bench vise near Sacramento, CA for $100. Per owner it weighs between 75-100 lbs.

http://sacramento.craigslist.org/tls/5394507672.html

 

[firworks]

Caterpillar wrench sets - 100/125$
http://peoria.craigslist.org/tls/5391017910.html

I don't know how much of a deal they are but if I didn't already have full metric and SAE sets of Wrightgrips I'd be considering this just because they're kinda cool being CAT. I'm guessing they are Snap-On as OEM?

 

[bubinga]

Table saw - $50

http://pittsburgh.craigslist.org/tls/5381582469.html
Motor needs repaired 50 obo

 

[sgs236]

Region: EAST

Location: PITTSBURGH

Item: Floor Model Chinese\Taiwan Drill Press

Price: $25.00

Link: https://pittsburgh.craigslist.org/tls/5397105698.html