Found a deal on craigslist? - List Here!

[Shiftless]

https://fingerlakes.craigslist.org/fuo/5446006454.html

That is an unbelievably great deal!
Some GJ member must be close to this one!
Each of those drawers is a foot wide!
GRAB IT!
Nobody else has noticed it because it is listed in the used furniture section with a title of used furniture!

 

[Colin Len]

Thank You! It's been been purchased and picking up tomorrow. Cheers!

I'm glad someone was able to snap it up! I really didn't know what it was but seemed unique and pretty cool. I have no need (room) for it so it's good it went to a GJ member

 

[Shop Dad]

24" Double Disk Sander - Awesome!!! - $500 (Page County, Virginia)

This is a truly AWESOME 24" DOUBLE DISK SANDER by J.A. FAY & EGAN
It weighs +/- #900. IT WILL MAKE YOUR TRUCK SQUAT.
The tables are Blanchard ground and sweet!
There is such great mass in the piece that the disks take about 15 minuets to come to a stop.
There is a motor break on the unit but it is not hooked up.
3 Phase, 5 hp 220/440 delta wound.
I will include several STICKY-BACK disks for it. Unknown grit at this time.
That is cosmaline on the table not rust.

Edit: I'm wondering if the "motor break" is actually a VFD.

That's a pretty incredible machine for $500.

 

[brooktre]

Old Grinder - $25 (Eagles Mere)

http://williamsport.craigslist.org/tls/5455830588.html

 

[danfromsyr]

it's gone now and I hope some GJ member grabbed it, but then it may end up at the local tool/fleamarket for $450.

That is an unbelievably great deal!
Some GJ member must be close to this one!
Each of those drawers is a foot wide!
GRAB IT!
Nobody else has noticed it because it is listed in the used furniture section with a title of used furniture!

 

[NUISANCE]

Not sure if legit or not, new 3 bay snap on box for $1500. If legit, it was only posted 6 hours ago.....

https://sfbay.craigslist.org/eby/tls/5459815297.html

 

[bennymic]

Swear I posted these this morning. Again, not a woodworker so forgive me if they aren't that great of a deal. Sounds skookum though:


DeWalt radial arm saw - $250 (Berryville)

vintage, 14" blade, 20" cross cut, 3 Hp, 3 Ph, Can provide photos


Rockwell 12" radial arm saw - $200 (Berryvillle)

Good condition, 220/110 volts, 1.5 hp

 

[dukes909]

Tilting arbor, I like.

J-Line 14" Disc Sander - $100

J-Line 14" disc sander ,120v single phase

 

[macgee]

Tilting arbor, I like.

J-Line 14" Disc Sander - $100

J-Line 14" disc sander ,120v single phase

That's a smoking deal, especially the edge sander if you need one..

 

[bubinga]

Tilting arbor, I like.

J-Line 14" Disc Sander - $100

J-Line 14" disc sander ,120v single phase

That's a smoking deal, especially the edge sander if you need one..

OKG!!! Just a :Little Bit" of a Smok'en deal.....
I'd Luv to have that.
EDIT
Single Phase yet!
EDIT,
"I'd Luv to have that."
No, BOTH of them.....LOL

 

[larryq]

Mac toolbox for $300 in Santa Clara, CA. I fear it may already be gone as I type this, but in case not, someone give em a call:

http://sfbay.craigslist.org/sby/tls/5461019825.html

 

[macgee]

1979 ENCO milling/ filling machine - $200 (Torrance, CA)

I'm not a fan of these type of mills with round columns but if it works well, then $200 is a great price. I bet it will be gone by this morning. They do make awesome drill press's and a lot of milling can be achieved within it's limits. You will be well versed in tramming if you use one of these mills. I say go for it.

It's a Enco 91000 mill

"1879 ENCO milling/Dill. 110volt with stand
$200 OBO
CALL or TEXT"

http://losangeles.craigslist.org/wst/tls/5461579753.html

If you want to see the PDF manual and spec's try here, the last page is the best info
https://app.box.com/shared/e21b39lgcs

 

[larryq]

Nice looking Kennedy-esque chest for $20 in Monterey CA. Made for Montomery Ward in the 1970s per the ad, a little surface rust but works fine.

http://monterey.craigslist.org/tls/5457071940.html

 

[bubinga]

1979 ENCO milling/ filling machine - $200 (Torrance, CA)

I'm not a fan of these type of mills with round columns but if it works well, then $200 is a great price. I bet it will be gone by this morning. They do make awesome drill press's and a lot of milling can be achieved within it's limits. You will be well versed in tramming if you use one of these mills. I say go for it.

It's a Enco 91000 mill

"1879 ENCO milling/Dill. 110volt with stand
$200 OBO
CALL or TEXT"

http://losangeles.craigslist.org/wst/tls/5461579753.html
If you want to see the PDF manual and spec's try here, the last page is the best info
https://app.box.com/shared/e21b39lgcs

might not be the best mill, but for my small work area, I would give $200..00 for it. Probably have to get rid of a drill press though.
LOL

Nice looking Kennedy-esque chest for $20 in Monterey CA. Made for Montomery Ward in the 1970s per the ad, a little surface rust but works fine.

http://monterey.craigslist.org/tls/5457071940.html

Nice little box for $20.00>
I'd get it too............LOL
Little wrinkle paint would spruce it right up.

 

[macgee]

DELTA 31-260X Drum Sander - $300 (Studio City, CA)

This is actually a good price for a 18" drum sander, these are big and useful puppies. This will sell very quickly for $300 so get on it if you need one. He posted his phone number in reply.

"DELTA 31-260X DRUM SANDER -

This sander was purchased for a specific job that was eventually cancelled.
It was literally used one time just to test how it worked.
Don't let the price fool you, It is basically brand new!!! and... PRICED TO SELL!!!

What you see is what you get... check out the photos below. It looks brand new because it is.


Will deliver - within Los Angeles"

http://losangeles.craigslist.org/lac/tls/5462963070.html

 

[sgs236]

Region: EAST

Location: PITTSBURGH

Item: Drill Presses - Powermatic

Price: $250.00

Link: http://pittsburgh.craigslist.org/tls/5456968536.html

Drill Presses
Powermatic
Single Phase Motors
Variable Speed RPM
(2) Heavy Duty Tables w/2 spindles each
Feed mechanism

 

[CNGsaves]

GJer in area please go snag this older SK set.

Region: - - - West coast USA

Location: - - - Monterey, CA

Item: - - - SK Metric 3/8" drive 15 piece socket set w/ green metal box

Price: - - - $ 29

Link:
https://monterey.craigslist.org/tls/5414947812.html

Made in USA, this set remains in good condition after decades of infrequent use. Sockets included range from 7mm. to 15mm. plus 17mm. and spark plug. Extensions are 2cm., 6cm. and 13.5cm. (approx. 0.75", 2.5"&5.5"). Drive ratchet is 20cm., just under 8", and works flawlessly. I bought this new and it has had good care. Asking $29. Sorry--texting is not available on this phone...and I don't respond to commercial inquiries.

Ted (831)234-9577

 

[macgee]

INCA 12" Table saw w/sliding table $500, Rockwell-Delta 14" (Very Nice) Band Saw $100
Wood shop machines (westwood, CA)

Swiss made table saw with sliding table and router table attached, I think this is the 12" version, they sold without slider or router for around $3,000.

The Delta band looks to be in excellent condition, steal for $100.

Also the Delta Mortiser is a good price but I would negotiate a group price with band saw. The rest of the stuff looks average but there is a lot of nice wood in the background that could possibly negotiated.

Machines a little old but well cared for
Delta Shopmaster Hollow Chisel Mortiser - Model MM300 $150
box of 4 Hollow Chisel Bits $85
Powermatic Drill Press - Model 1140f 1989 - $200
Duracraft Bench Grinder - Model 606050 $50
Band Saw - Rockwell Model 14 $100
Joiner/ Planer - Makita 300mm Model 2030 $1000
Band sander $50
Inca Table saw - 1994 Type 341 033 21 $500


http://losangeles.craigslist.org/wst/tls/5465996839.html

 

[larryq]

Nice vintage 1/2 HP Craftsman motor with a couple of attachments for $10 in Dublin, CA. Wouldn't recommend keeping that grinding wheel on, but a buffer would do well.

http://sfbay.craigslist.org/eby/tls/5465938567.html

 

[macgee]

Nice vintage 1/2 HP Craftsman motor with a couple of attachments for $10 in Dublin, CA. Wouldn't recommend keeping that grinding wheel on, but a buffer would do well.

http://sfbay.craigslist.org/eby/tls/5465938567.html

That's funny, I've got the exact same motor with two wire wheels, I was actually just using it today. If it has the 1750 rpm, then it makes for a nice and safe wire wheel set up, I prefer it to my 3250 rpm set up, the wire needles that fly off into my forehead don't hurt as much with the slower rpm. $10 is a great price if it works.

 

[bubinga]

Yeah, those are nice motors, I have a few.
They are 3450 though.
3/4 or better 3450 is nice for a small table saw or smaller jointer though.


Sent from my MotoG3 using Tapatalk

 

[bubinga]

That power magic, if it's the same guy I think it is, he usually has some nice things at decent prices.
He had an older delta 8inch jointer for $400.00 IIRC

Sent from my MotoG3 using Tapatalk

 

[macgee]

Craftsman Hybrid Table Saw Model 351.218330 - $250 (Stevenson Ranch)

Might not be the best deal but offer the guy $200

Used Craftsman Contractor Table Saw for sale. Asking $250 OBO, new this table saw is around $600. I purchased another table saw and haven't used this one in a number of months, and now it's just taking up space. Pick up is in Stevenson Ranch. Can help load if picked up during the weekend. Comes with original manual.

http://losangeles.craigslist.org/sfv/tls/5466709053.html

 

[bubinga]

Would be a very good deal at $200,00!.
Looks like a nice fence too.


Sent from my MotoG3 using Tapatalk

 

[Shiftless]

Location: Central Valley CA

Big Record vise (vice!) with a decent stand for $60

http://fresno.craigslist.org/tls/5466419816.html

 

[macgee]

Vise Chas. Parker Co.Made in USA No.953 3" Jaws - $40 (Olympia)

Somebody go save this in the Seattle area for $40 but need to inspect the slide support to make sure it's not cracked or welded.

Charles Parker Co vise. No. 953 in good working condition.Antique.
3" jaws.Medium duty vise.Not a large vise but solid and well made mid size vise.
Mount stationary on the edge of the bench.
Made in USA.
Leave a contact number if interested. 40.00


http://seattle.craigslist.org/oly/tls/5434691137.html

 

[Cypherian]

LATHE \\

GO GO price is nice for what appears to be a good unit, and yes if I had the money I would be on the way to look at it !!

http://southjersey.craigslist.org/tls/5467938258.html

 

[macgee]

Craftsman air compressor twin cylinder 120 volt for $125 obo (Sylmar, CA)

I would offer $80-$100

Not a bad little compressor with 5.8 CFM@90 PSI spec. These are pretty quiet being belt driven and it's a two cylinder. You don't see them often at 120v with these specs.

Im selling 12 gallon Craftsman air compressor twin cylinder 120 volt for $125 obo call

http://losangeles.craigslist.org/sfv/tls/5467966193.html

 

[In The Doghouse]

Bowling alley lane wood*@#$-*@#$$175*@#$(Kirkwood, MO)*@#$

https://stlouis.craigslist.org/atq/5419944979.html

 

[dkroth]

Bowling alley lane wood*@#$-*@#$$175*@#$(Kirkwood, MO)*@#$

https://stlouis.craigslist.org/atq/5419944979.html

Another member here posted his experience helping a friend load some of these lanes from a bowling alley auction in NW Missouri. This is probably from that same location.

 

[larryq]

Location: Central Valley CA

Big Record vise (vice!) with a decent stand for $60

http://fresno.craigslist.org/tls/5466419816.html

Is there something up with the back jaw, or is that how they were designed?

Edit: looks like that's how the design is. A better view from another one and a different model:

 

[CNGsaves]

^ ^ ^ For $60 on a stand, that Record vise is a smokin' deal. Someone grab it !!

 

[macgee]

Bowling alley lane wood*@#$-*@#$$175*@#$(Kirkwood, MO)*@#$

https://stlouis.craigslist.org/atq/5419944979.html

Nice find, that's a great price. Please jump on it

 

[Shiftless]

^ ^ ^ For $60 on a stand, that Record vise is a smokin' deal. Someone grab it !!

That's what I said!
If that was near one of us, it would be gone! The vise alone is worth more than $60.

macgee: How much would 6 feet of that go for in L.A.?
Another smokin' deal on C/L
Seriously, talk about a fantastic workbench top! 3 inches thick edge grain laminated maple?

 

[macgee]

That's what I said!
If that was near one of us, it would be gone! The vise alone is worth more than $60.

macgee: How much would 6 feet of that go for in L.A.?
Another smokin' deal on C/L
Seriously, talk about a fantastic workbench top! 3 inches thick edge grain laminated maple?

I totally agree on the vise, even comes with a stand.


In LA, I seen these sell from $800-$2000+ and they were smaller sections (crazy prices). I've seen them made into dining tables, conference tables and for flooring in high profile rooms. It wold be great for a hallway, although 3" thick would make that tough.

That doesn't look like maple but more like a vertical grain Douglas Fir but that would be way too soft so not sure.

 

[larryq]

SnapOn roller for $200 in San Jose, CA. "8 drawer snap on tool box, bought from Wyotech Fremont liquidation sale. All drawers operate, solidly built, some cosmetic flaws due to student use. Perfect for home use. No key for lock."

https://sfbay.craigslist.org/sby/tls/5469009250.html

 

[larryq]

I think(?) this is a good deal, a Marquette arc welder for $95. Looks to be in good shape. Again, in San Jose:

http://sfbay.craigslist.org/sby/tls/5466378395.html

 

[bubinga]

That snap on is real nice.

Sent from my MotoG3 using Tapatalk

 

[macgee]

Athol 614 1/2 machinists vise - $50 (Hemet, CA)

These are excellent vise's. $50 is a good deal, that's like 0.75 ¢/lb.

It's actually a 4 1/2" jaw.

Nice old Athol 614. This is a machinists vice. That means the jaws are smoorh without teeth.

This is a old heavy vice. It was made in the 50's or before. The vise works perfectly. The handle to loosen and tighten is not bent.

Theses are highly desired and sell for way more than I'm asking.


http://inlandempire.craigslist.org/tls/5466762347.html

 

[derek245583]

https://cincinnati.craigslist.org/mat/5469401546.html

$100 for 8 ft section