Garage Overhaul Using Rust Bullet for the Floor

[dubber]

Ah, yes that makes sense i missed typing "in NA" (north america) unfortunately. Living abroad in that situation has a huge advantage. Any new euro car in a magazine is already available whereas we have to wait to see it if will be launched in our markets.

 

[EMC2]

Ah, yes that makes sense i missed typing "in NA" (north america) unfortunately. Living abroad in that situation has a huge advantage. Any new euro car in a magazine is already available whereas we have to wait to see it if will be launched in our markets.

True, but on the flip side there's probably no better place in the world to be a car fanatic than in the USA. Prices almost everywhere else are considerably higher.

 

[dubber]

True, but on the flip side there's probably no better place in the world to be a car fanatic than in the USA. Prices almost everywhere else are considerably higher.

When you were abroad and a Beemer fan did you ever take advantage of the euro delivery at the BMW Welte? I did a tour there this summer and was blown away. Truly amazing! I was there with my father in-law (long time Jag man) and he was close to changing to a BMW just based on what we witnessed and heard about. So close but no cigar unfortunately haha.

 

[EMC2]

Unfortunately I did not. Although I seriously considered it several times, i just never had the time. I still want to add a proper M car to my list one day, so maybe then...

 

[dubber]

Unfortunately I did not. Although I seriously considered it several times, i just never had the time. I still want to add a proper M car to my list one day, so maybe then...

That sounds like a good plan.

 

[dubber]

Well your set-up has definitely influenced the look I've been going for. Just picked up a 32" Husky like the one you have on the right. Colour scheme works well with my GLI as well but 5 coats of red scares me hahaha.

 

[EMC2]

Dubber I Just took a look at your thread. Great result with the Husky cabinets.

As much as the red was a daunting task, I would do it again in a heartbeat.
Particularly in the daylight, the red has an almost luminescent look. Really vibrant. I think this is because it was on a white basecoat rather than a gray one. More light can reflect back though the paint (if that makes sense).

 

[AndrewnTX]

Gorgeous! That's one to be proud of, great job!!

 

[EMC2]

Gorgeous! That's one to be proud of, great job!!

Thanks Andrew

 

[Requin6]

Great looking garage! Very clean, nice ride, great color combos. Well done!

 

[hades02]

Great looking garage. I hope to someday have a two bay that looks as nice. I see that you are a detailing fanatic as well. Some DP and Blackfire products as well as a ton of MF's with polishing pads all in sealed totes.

 

[EMC2]

Great looking garage! Very clean, nice ride, great color combos. Well done!

Thanks Requiun.

Great looking garage. I hope to someday have a two bay that looks as nice. I see that you are a detailing fanatic as well. Some DP and Blackfire products as well as a ton of MF's with polishing pads all in sealed totes.

Thanks for the feedback. Yes I only use DP in the foam gun and the Blackfire range is my absolute favorite for a black car. I gather you know a thing or two about detailing also what's in your detailing kit?

 

[hades02]

I know a little. It's a hobby not a job. I use a Flex polisher. Product lines for wash Duragloss, OPT ONR, Megs Deep Crystal or Megs Gold (depending on stripping wax or not). Polishes include Menz, Megs Pro line, 1Z and others. Sealant WG DGPS 3.0. Waxes XMT or DP. Took a break for the last couple of years from the forums, now BF seems to be highly talked about. Thanks for the info regarding BF being great for a black car.

 

[draider]

Beautiful garage. You have a great attention to detail, and are obviously not adverse to researching a product. Good info, thanks for sharing.

 

[EMC2]

I know a little. It's a hobby not a job. I use a Flex polisher. Product lines for wash Duragloss, OPT ONR, Megs Deep Crystal or Megs Gold (depending on stripping wax or not). Polishes include Menz, Megs Pro line, 1Z and others. Sealant WG DGPS 3.0. Waxes XMT or DP. Took a break for the last couple of years from the forums, now BF seems to be highly talked about. Thanks for the info regarding BF being great for a black car.

I've heard a lot of good things about WG products, but not had the chance to try them out yet. I can definitely see a Flex polisher being added sometime in the future (for the tougher jobs), and keep the GG for the sealants and waxes.

Beautiful garage. You have a great attention to detail, and are obviously not adverse to researching a product. Good info, thanks for sharing.

Thanks - something of a risk I guess, but hopefully a well calculated one. The hot tire pickup that has plagued so many made me really zone in on the temperature rating of the coatings. Hopefully the principle holds true - so far so good. I've been particularly impressed with how easy it is to clean up.

 

[hades02]

The flex is a great machine. Bought the new 4" backing plate for spot buffs. I think once you pick a flex up you won't pick up the GG again.

 

[AgDriller]

EMC2 - great looking garage - and car! I've got a 928 that my Dad bought new in '82 and I bought from him in '92. It's on my list to refurb when I get my garage/shop finished.

Question on the Rust Bullet - I've got a 40' X 60' that I'm considering using Rust Bullet for the floor. How many gallons did it take to do your garage? Also does it leave any tire marks as far as rubber on the floor? My concrete floor has tire marks from trailers, four wheelers and the fork lift used to erect the metal building.

Thx.

 

[EMC2]

EMC2 - great looking garage - and car! I've got a 928 that my Dad bought new in '82 and I bought from him in '92. It's on my list to refurb when I get my garage/shop finished.

Question on the Rust Bullet - I've got a 40' X 60' that I'm considering using Rust Bullet for the floor. How many gallons did it take to do your garage? Also does it leave any tire marks as far as rubber on the floor? My concrete floor has tire marks from trailers, four wheelers and the fork lift used to erect the metal building.

Thx.

Hi AgDriller
Thank you.
I used 3 galllons for my floor and that gave me 2 very good coats.
Ive not had any hint of tire marks at all even when the tires have been hot. However environmentally, it has not been hot yet since installing in December, so this summer will be a good test.

Just be sure to strip the current surface thoroughly, and allow to dry for several days.

 

[AaronTTRS]

This is awesome, nice work!!!!!!

Aaron

 

[EMC2]

Thank you Aaron.

 

[jasonvt]

do you have the paint code for the red that you used? Hope you dont mind, but I want to steal your color idea. Instead of Porsche, Ill have a Holden flag tho

 

[69bigblok]

Fantastic view from the drive. I find myself checking this thread often and marveling at the simplicity and sophistication of the design. One of the nicest triples I have ever seen.

Totally agree. I look at this garage more than any other!

 

[plym49]

Can Rustbullet be applied over good existing paint? Not on floors; in general.

 

[EMC2]

do you have the paint code for the red that you used? Hope you dont mind, but I want to steal your color idea. Instead of Porsche, Ill have a Holden flag tho

Hi Jason

The paint was:
Behr Porch & Patio. Low lustre floor. Base 6300
Color. Red Baron - PFC-03.

Be prepared for many coats, but a worthwhile result in the end. I love the color and would do it again despite the effort. Also be very sure to maintain a wet edge to avoid streaking.

Just a side note. I fully agree that using a gray primer would have made the job easier, but I really wonder if the final result would have the same "translucent" look to it.

Good luck and please share some photos when done.

 

[EMC2]

Can Rustbullet be applied over good existing paint? Not on floors; in general.

I'm afraid I can't give you any informed opinion there. I only researched for concrete floor application. I would take a look at their site. They seem to have a lot of info available.

 

[jasonvt]

Hi Jason

The paint was:
Behr Porch & Patio. Low lustre floor. Base 6300
Color. Red Baron - PFC-03.

Be prepared for many coats, but a worthwhile result in the end. I love the color and would do it again despite the effort. Also be very sure to maintain a wet edge to avoid streaking.

Just a side note. I fully agree that using a gray primer would have made the job easier, but I really wonder if the final result would have the same "translucent" look to it.

Good luck and please share some photos when done.

Thanks! Will definitely post pics when its done

 

[G20-Budo]

EMC2, great job on your garage, it looks SO clean.

I have a few questions, if you were to do it again, do you think you'd consider Epoxy as a floor coating? Do you find the floor to be very slippery when wet?

 

[EMC2]

EMC2, great job on your garage, it looks SO clean.

I have a few questions, if you were to do it again, do you think you'd consider Epoxy as a floor coating? Do you find the floor to be very slippery when wet?

Thanks. I would definitely use Rust Bullet again. I'm not into the look of flakes, and I really did not want to go through the process of grinding.

The surface is holding up perfectly. It's very easy to clean and I've had no hot tire issues even after some really hot days and hot tires. The floor is no more slippery than expected when wet. I wouldn't suggest running on it, but for normal use it seems perfectly safe.

 

[G20-Budo]

Where I live it gets...well REALLY hot. We see temps of 118F in the middle of summer (that's not exaggeration). I have had the grey paint (that was on my floor when I moved in) come up on both sides that we park on. Though this paint looks interesting, I'm seriously leaning towards epoxy..and/or race deck. I do a fair amount of car work in my garage, and ATF or brake fluid could make it's way onto the floor. If not cleaned up soon enough, it wrecks havoc on painted floors.

Thanks for the info!

 

[MajorLeeGassole]

PLEASE. Tell me the colors, codes, brand, etc. What an amazing garage!

 

[KPSquared]

Have you tried reading the thread? Pretty sure it's all there.

 

[MajorLeeGassole]

Was cooking dinner earlier and trying to look at this at the same time. Now I had the time to scroll through and went DUH! Thanks for beating me to it though.

 

[KPSquared]

Sorry, I looked like a *****. . .not my intention. . .

 

[MajorLeeGassole]

Sorry, I looked like a *****. . .not my intention. . .

Not at all. I have to remember to read before I post!

 

[EMC2]

Where I live it gets...well REALLY hot. We see temps of 118F in the middle of summer (that's not exaggeration). I have had the grey paint (that was on my floor when I moved in) come up on both sides that we park on. Though this paint looks interesting, I'm seriously leaning towards epoxy..and/or race deck. I do a fair amount of car work in my garage, and ATF or brake fluid could make it's way onto the floor. If not cleaned up soon enough, it wrecks havoc on painted floors.

Thanks for the info!

I don't think the heat would be an issue based on the service temp of Rust Bullet. From their data sheet;

"After curing, all Rust Bullet coatings have a service temperature range of 314°F (157°C) continuous, and can tolerate maximum temperatures between 617°- 662°F (325°-350°C) for up to 72 hour periods."

I can't comment on the brake fluid risk as I haven't tried that. I'd suggest contacting the manufacturer on that one.

 

[OpFlash]

Amazing job!!

 

[mtmd11]

Fantastic space.

The colors are spot on for the walls, and the cabinets match 'just so'.

I agree it looks like a European Porsche Showroom. Minimalist and elegant but functional.

Having a Boxster, I am also a fan of the brand.

 

[I PLAY FOR KEEPS]

Great space! I love the color combo and really like your organization

 

[I void warranties]

looks like rustbullet.com updated their "faq" to include concrete application:

Will Rust Bullet protect a concrete shop floor?

Yes. Rust Bullet, with its Superior Patented Technology for rust and corrosion control provides outstanding protection to many surfaces, including concrete. Rust Bullet not only improves the appearance of concrete, it provides an impervious shield allowing easy clean up of oil, grease and chemical spills along with strong protection against impact and abrasives. Concrete has been a reliable and versatile product for centuries. Chosen for its strength and durability, concrete is expected to withstand the most abusive conditions. It is subjected to the destructive effects from harsh chemical spills, abrasive objects, moisture and the impact from heavy tools and machinery often resulting in an unsightly appearance and damage requiring costly repairs or replacement.

Rust Bullet protective coating will:
Provide excellent chemical resistance
Provide protection from abrasives
Seal a surface from moisture
Allow easy clean up of spills
Prevent concrete from sweating
Reduce dust
Fill cracks, gaps, and chips up to ¼ of an inch
Enhance appearance
Add years of life to concrete surfaces

Power wash or simply rinse off dirt and debris and let the surface dry completely before applying Rust Bullet. Two to three coats of Rust Bullet is usually sufficient for most concrete applications depending on the concrete’s condition and existing damage. Porous concrete and heavy traffic areas may require additional coats. Rust Bullet is self leveling and can fill in cracks, gaps and chips up to ¼ inch. If a slip resistant surface is desired, sprinkle silica or similar fine sand over a tacky coat of Rust Bullet, allow just enough time for the sand to adhere, then apply the final coat of Rust Bullet.

 

[EMC2]

Amazing job!!

Fantastic space.

The colors are spot on for the walls, and the cabinets match 'just so'.

I agree it looks like a European Porsche Showroom. Minimalist and elegant but functional.

Having a Boxster, I am also a fan of the brand.

Great space! I love the color combo and really like your organization

Been away for a while. Thanks for the comments guys.