Harbor Freight Coupon Thread

[TCB]

OK, I don't care who you are . . . That's funny right there!

 

[Lifted4]

Found 2 different harbor freight flyers in the Sunday paper.
1 small ad in the TV guide section and a full 2 page ad in with all the other sales circulars.

 

[jimwalt]

Thanks so much Upgrading!!!!!!!!!!!!!!!

Could you also do the Tape measure, Flashlight and Multi Meter. I believe they all expire on 10/23/13 as well.

Thanks again!

 

[jimwalt]

Found 2 different harbor freight flyers in the Sunday paper.
1 small ad in the TV guide section and a full 2 page ad in with all the other sales circulars.

Could you please scan and post. Also where are you located (what newspaper)?

 

[Lifted4]

They were in the Houston Chronicle. I will post them.

 

[jimwalt]

Scissors. Any good jimwalt ?

Haven't used the scissors yet. Just put them in my car toolbag.

 

[kapster]

Scissors. Any good jimwalt ?

I have a pair at home and work, they're not bad. I use them at work to cut scotch brite pads which would be silly to use expensive scissors on. At home Garage I cut out gaskets, ect. No complaints.

 

[Samson]

Here's some coupons for y'all!

 

[Vegaman_Dan]

I have a pair at home and work, they're not bad. I use them at work to cut scotch brite pads which would be silly to use expensive scissors on. At home Garage I cut out gaskets, ect. No complaints.

I love the 99 cent black scissors. I buy a lot of them and keep on the wall for convenience. They cut what I need and do it very well. Worth tossing a pair into every tool box you have.

 

[keithh2oskier]

They seem to cut sandpaper and thats about it. If I try and cut regular paper they are worthless. But hey for free, ill keep them around and not have to listen to my wife yell at me for dulling up her nice scissors...

 

[the1nonlyjl]

anyone got a coupon for welder?

 

[rslaback]

anyone got a coupon for welder?

which one?

 

[diggerrick]

Bar Clamp

Worth picking up a couple for free (I have 5 or 6), but I wouldn't pay even $1 for them.

http://www.garagejournal.com/forum/showpost.php?p=3198159&postcount=5286

 

[diggerrick]

Magnetic parts tray.

Thanks - I never seem to accumulate enough of these.

 

[Kevin54]

My flyer is out in the shop. I'll look and scan it off if I do.

One question though, the coupon has a front and a back. Won't that make a difference or not with HF?

And for ones that may not know......go to HF's website and there is a place that you can check mark and they will send you fliers by e-mail and also by snail mail. I received a rather thick coupon book in Saturday's mail.

Anyways, If I have it, I'll scan it for you.

 

[lasthope05]

Do anybody have a coupon for the 6 ton jackstands, or know if they usually go on sale? Ive been looking around for months with no luck.

Sent from my SGH-T989 using Tapatalk 2

 

[Fitzgerald]

Man, I love me some HF, but these are too funny!!!

I haven't laughed out loud like that in a while. I think you have to be a real HF lover to get most of these jokes.

Thanks for posting.

 

[TerryH]

I need to get a few of those ***** lamps for some very close friends who fit that description well.

 

[unslow1]

Thanks for the cleaner scans of the freebies.

 

[upgrading]

Thanks - I never seem to accumulate enough of these.

Thanks for the cleaner scans of the freebies.

You are welcome.

 

[upgrading]

Multimeter.

 

[upgrading]

Tape Measure

 

[upgrading]

90 amp flux wire welder

 

[upgrading]

170 amp mig/flux wire welder

 

[the1nonlyjl]

170 amp mig/flux wire welder

Thank you upgrading. That's exactly what I was looking for!

 

[bestonearound]

Looking for the parts washer coupon.

 

[Lifted4]

Anyone have a Q for the Air Cutoff tool free with $49.99 purchase ?

 

[unslow1]

Anyone have a Q for the Air Cutoff tool free with $49.99 purchase ?

Mine expired 6/30

 

[jimwalt]

Anyone have a Q for the Air Cutoff tool free with $49.99 purchase ?

It's on sale for $8.29, use the 25% off coupon and get it for $6.22.

 

[j p smith]

Got this one this morning! Hope someone can use it. Later, Jeff

 

[j p smith]

Sorry, can't figure how to get the whole coupon. Jeff

 

[Fast LT1]

Never mind it's on their website

 

[j p smith]

Thanks Fast.

 

[SharkBait]

The 20 Ton press is on sale for $169.99, use the 25% off coupon below to get it for $127.49

The press #32879 or #60603

25% coupon (valid 7/4 only)
http://www.harborfreight.com/25off-july2013.html#

 

[skulldrinker]

The 20 Ton press is on sale for $169.99, use the 25% off coupon below to get it for $127.49

The press #32879 or #60603

25% coupon (valid 7/4 only)
http://www.harborfreight.com/25off-july2013.html#

I believe I just saw it for $149 somewhere just in case they don't take the 25% off on a sale price.

 

[CoryZ]

There's a 25% off coupon valid until Sept (pp 1 of the thread on SD site). Don't feel you need to hurry and buy today.

 

[aqr81]

What is the SD site?

 

[alantala15]

Can someone give me a link or a good scan of the 20 ton press. the ones i saw on the thread werent in good enough shape for the barcode or numbers to show or to look legit. i really need one. thanks in advance

 

[SharkBait]

SD is SlickDeals, link to Harbor Freight thread below (and there is a 25% off coupon good until 10/29/13 in there)
http://slickdeals.net/f/1276399-Harbor-Freight-Coupon-Thread

 

[SharkBait]

Can someone give me a link or a good scan of the 20 ton press. the ones i saw on the thread werent in good enough shape for the barcode or numbers to show or to look legit. i really need one. thanks in advance

If you're asking about a coupon for the 20 Ton priced at $169, you don't need it. That is the current sale price in the store. The sale price -25% (or even 20%) is a better deal than the $149 coupon that is floating around.

See the post above for a link to the 25% that expires in Oct.