To avoid these ads, REGISTER NOW!

How I Unloaded A 44" Box From Pickup

To avoid these ads, REGISTER NOW!

BK13

Well-known member
Joined
Mar 1, 2013
Messages
2,692
Location
PDX, OR
I'd be worried about my fat *** and a 300lb. box would bust the 2x12s...
 

pfhWJ

Well-known member
Joined
Feb 2, 2013
Messages
454
I t was ***** to unload the fricken thing. basically did a control fall out the back of a pickup. they sure do pack those things well.
 

ADCS

Well-known member
Joined
Jan 4, 2014
Messages
75
Location
Toronto
I just removed all of the drawers and then lifted the empty box out.
 

ScottsGT

Well-known member
Joined
Jan 1, 2014
Messages
4,883
Location
Lake Wateree, SC
I just enlisted the help of a few teenagers! But it was a trailer, not as far down to go. Unbox on the trailer, placed a sheet of plywood on the edge and rolled it down.
 

hayhauler71

Well-known member
Joined
Dec 29, 2013
Messages
362
Location
MN
I like the fact you used a sweet truck to get it home What year would that be 69-72 Chevrolet c20 I cant see the grill ?
 
To avoid these ads, REGISTER NOW!

bczygan

Well-known member
Joined
Nov 4, 2009
Messages
22,002
Location
DETROIT! Arsenal of Scrappers
Used an AstroVan for transport. It had the rear seats removed.
Had the store remove the skid and put the box on their hydraulic lift upside down, and take the cardboard bottom tray off, so the casters stuck up in the air.
We then slid it onto the van at floor level. It just fit.

When I got home, I parked at the curb at the corner of the street, where there was sidewalk.

Slid it out by myself until the box set at an angle with one edge of the box on the ground and the other just on the lip of the floor of the van. Remember, it's upside down, so this is the edges of the top. But they pack these pretty well.

It's now far enough out, so I rotate the van end up until the box is on it's end and sitting on the cement.

Then I just continued to tip it over long ways, onto the casters. Rolled it up the sidewalk to the garage.
 

zkling

Well-known member
Joined
Jan 23, 2007
Messages
16,939
Good job. Looks like it took you for a little ride. :thumbup: I'm loving the old Kawasaki enduro in the background F7?
 
OP
O

outdoorsman310

Well-known member
Joined
Aug 23, 2013
Messages
915
Location
DE
Good job. Looks like it took you for a little ride. :thumbup: I'm loving the old Kawasaki enduro in the background F7?

thats my first bike! '77 Ke250 street legal. I used to ride it in the winter but didn't feel like retagging it this october. I will soon though. It is still insured and i love riding it! The low beam went out so I need a new sealed beam 6v headlight for it.
 

carterbeauford

Well-known member
Joined
Oct 2, 2011
Messages
1,550
Location
NW PA
I hauled my 72" box home in a crate on a tilt trailer and still had to drag it off my 4x4 ATV it was so heavy.
 

rice rocket

Well-known member
Joined
Mar 24, 2011
Messages
3,175
I used a ramp too, but I rolled it down end over end instead of sliding it because my ramp is covered in grip-tape material.
 

RedF

Well-known member
Joined
Aug 31, 2013
Messages
203
Location
Central Alberta
I unloaded a similar sized toolbox today. Laying on its back in my pickup, I slid it onto the tailgate and past the balance point, then gently let it down onto two wheels (stopped at 45-ish degrees), then stood upright.
 

Bigblue&Goldie

Well-known member
Joined
Mar 12, 2009
Messages
10,782
Location
AZ
Why not just go ask a neighbor for help? :dunno:

FWIW, my buddy and I loaded and unloaded both of my 44" boxes by hand and my tailgate is 3' off the ground.
 
OP
O

outdoorsman310

Well-known member
Joined
Aug 23, 2013
Messages
915
Location
DE
I had the ramps handy and wanted to see if it worked. I was also cleaning the garage and did not want people looking at all of my ****.
 
To avoid these ads, REGISTER NOW!
Top Bottom