Impact Gun Muffler Kit. HP decrease

[Sunrise]

Is this a typo?

"Maximum torque with muffler is 100 ft. lb."

http://buy1.snapon.com/catalog/item...id=888&supersede=&store=snapon-store&tool=all

anyone have on their gun? how is it working out for you?

 

[Diesel-Mech]

I have never installed the muffler that came with my MG725 but I am fairly sure that is a typo.

 

[Sunrise]

MG725 comes with the muffler kit?

my MG31 did not.

 

[gofastman]

to lower the SPL of an that gun to 85db you would have to reduce the output to 100' lbs

 

[Diesel-Mech]

Yes, my MG 31 did not come with a muffler and I was unaware there was one available for it.

 

[tatra]

bearings would just pack it in anyways unless you have a good water seperator

 

[gofastman]

ummm, what?

 

[tatra]

muffler bearings

 

[Merkava_4]

I'm always taking mufflers off of air tools; I like the increased power with the tool's ability to breath better.

 

[Torque1st]

The information is not a typo. Nothing is free. Everything comes with a cost. The increased back pressure from the muffler reduces the tool torque rating.

 

[eschoendorff]

Huh... my MG725 cam with some mesh that I installed in the handle to control the noise... I don't know if it is the same as the above mentioned muffler kit. I will say that even with the mesh installed in the handle, my MG725 still runs like a raped ape!

 

[Diesel-Mech]

Huh... my MG725 cam with some mesh that I installed in the handle to control the noise... I don't know if it is the same as the above mentioned muffler kit. I will say that even with the mesh installed in the handle, my MG725 still runs like a raped ape!

Thats the muffler that is in question.

The information is not a typo. Nothing is free. Everything comes with a cost. The increased back pressure from the muffler reduces the tool torque rating.

I am very reluctant to believe that a little piece of mesh and a perforated cover is going to whittle a 810 ft. lb impact down to 100 ft. lb....I believe snap-on intended to say that the muffler will reduce torque by 100 ft. lb.

 

[eschoendorff]

Thats the muffler that is in question.


I am very reluctant to believe that a little piece of mesh and a perforated cover is going to whittle a 810 ft. lb impact down to 100 ft. lb....I believe snap-on intended to say that the muffler will reduce torque by 100 ft. lb.

That would make more sense.... even with the muffler (which I CANNOT believe is worth anywhere NEAR $8.**!!!!) my MG725 is plenty loud and definitely well over 100 ft/lbs strong.

 

[Torque1st]

Sorry, you are correct, that would be a typo if it dropped it down to 100#. Your reading is how I interpreted it (by 100#). It reduces the torque rating. Even reduced by 100# it is a nice tool.

 

[eschoendorff]

Sorry, you are correct, that would be a typo if it dropped it down to 100#. Your reading is how I interpreted it (by 100#). It reduces the torque rating. Even reduced by 100# it is a nice tool.

I can vouch for that. I didn't know what I was missing before I bought one. Now, if I had an IR 2135 or something, would I buy the MG725... probably not. But I decided to go with one because my dealer got me a good deal and I was looking for a "real" gun. My dealer can also service it locally shoyld it ever need anything....

 

[gofastman]

Thats the muffler that is in question.


I am very reluctant to believe that a little piece of mesh and a perforated cover is going to whittle a 810 ft. lb impact down to 100 ft. lb....I believe snap-on intended to say that the muffler will reduce torque by 100 ft. lb.

As am i reluctant to beleve it will bring the noise level to anywhere near 85DB

 

[Pedro-snapon]

that's a typo, i think they meant to type 800...

muffler kits come with the mg725 but not with the mg31 although they are available for the mg31

 

[Torque1st]

They probably don't have to figure in the banging on a fastener, just the running tool, like that is how it is used...

 

[Sunrise]

that's a typo, i think they meant to type 800...

muffler kits come with the mg725 but not with the mg31 although they are available for the mg31

it better be. haha

but still, #1 and #8 key pad far far away from each other