To avoid these ads, REGISTER NOW!

Is this a fire hazard?

S

streetcore

Well-known member
Joined
Feb 9, 2013
Messages
45
Location
Canada
I peeled back some insulation in my mom's attic today looking for places to air seal and found what looks like burn marks on some tar-paper faced insulation (see attached pics). The marks follow the path of a wire running to a track light in the kitchen. It used to run four 60W bulbs, but I recently switched them to 40W equivalent LED bulbs. The light is controlled by an older dimmer switch.

This doesn't look good to me. Could it indicate a fire hazard?
 

Attachments

  • DSCN1350.jpg
    DSCN1350.jpg
    141.9 KB · Views: 249
  • DSCN1349.jpg
    DSCN1349.jpg
    145 KB · Views: 257
  • DSCN1348.jpg
    DSCN1348.jpg
    145.2 KB · Views: 288
Last edited:
To avoid these ads, REGISTER NOW!
W

wyliesdiesels

Well-known member
Joined
Aug 14, 2012
Messages
20,073
Location
Modesto, CA
IMPO that looks more like stains than burn marks.

Notice the water marks on the dry wall?

Im thinking that there was a water leak and the blackness was transferred from the wire to the insulation.

EDIT: Other idea is spray paint now that i look at the third photo.
 
Last edited:
OP
S

streetcore

Well-known member
Joined
Feb 9, 2013
Messages
45
Location
Canada
Thanks for the quick reply. I wondered if it might be moisture related. The attic is not well insulated and there are air leaks everywhere, which is why I started peeling back the insulation in the first place. When I saw those black marks it kind of scared me.
 
L

LS6 Tommy

Well-known member
Joined
Dec 27, 2013
Messages
26,162
Location
Northern NJ
I was thinking it's some sort of a stain from the insulation, too. I may very well be wrong, but I don't know if that type of wire is supposed to be used that with with that box, at least not without some kind of bushing. Please correct me if I'm wrong...
 
K

KRB52

Well-known member
Joined
Sep 25, 2013
Messages
2,650
Experiment time. Turn on the lights for that box, then go back into the attic. Give it a little bit, then touch the wire (insulated part). If there is a problem, you should feel it being too hot. Also, give the black areas in the insulation the "sniff test." If it smells burnt, eh, she may have a problem. If you try this, make sure you wear a dust mask so you don't inhale fiberglass.
 
R

rlitman

Well-known member
Joined
Oct 18, 2010
Messages
24,667
Location
Long Island
KRB52 said:
Experiment time. Turn on the lights for that box, then go back into the attic. Give it a little bit, then touch the wire (insulated part). If there is a problem, you should feel it being too hot. Also, give the black areas in the insulation the "sniff test." If it smells burnt, eh, she may have a problem. If you try this, make sure you wear a dust mask so you don't inhale fiberglass.
Click to expand...

I'd avoid touching the wire. If the insulation is going, it may flake off and shock you.

If you had a thermal camera, the solution is easy.

Barring that, I'd turn the power off, and give the wire some flexing. See if the insulation has gotten "crunchy" from being overheated.

To me, that looks like kraft paper faced insulation, and I'm not familiar with tar-paper faced insulation. But let's for a moment say that the fiberglass side of that paper were coated with tar. A warm wire could melt that tar and have it soak through the paper like that.
 
Last edited:
W

wyliesdiesels

Well-known member
Joined
Aug 14, 2012
Messages
20,073
Location
Modesto, CA
To me, the third photo looks like the wire is glossy as in black spray paint.

If the wire was getting hot, the insulation wouldnt be shiny glossy like that.

LS6 Tommy said:
I was thinking it's some sort of a stain from the insulation, too. I may very well be wrong, but I don't know if that type of wire is supposed to be used that with with that box, at least not without some kind of bushing. Please correct me if I'm wrong...
Click to expand...

Good catch.

There should be clamps on that wire.
 
OP
S

streetcore

Well-known member
Joined
Feb 9, 2013
Messages
45
Location
Canada
I double checked the wire insulation and it looks good. No cracking or flaking. The light was on when I first discovered this and the wire didn't feel hot to the touch then. There was some tar on the wire, which may have made it look glossy in the picture. I was able to wipe that off.

I moved the wire, put the insulation back down and will check it again later.

Unfortunately I don't have a thermal camera. I wish I did and I think it would really come in handy with this insulation project.

I wondered about the wire clamps as well. I'm hoping to get electrician friend to come over for a look on the weekend. There's a couple things in that attic that look a bit sketchy.
 
To avoid these ads, REGISTER NOW!
D

DenisG

Well-known member
Joined
Jul 14, 2013
Messages
1,278
Location
Milwaukee
Don't know if you can read any identification numbers on that cable, but if it's rubber insulation it's probably past it's lifetime. Rubber insulation was discontinued in the 60s.
 
D

Dagny

Well-known member
Joined
Jul 25, 2014
Messages
3,019
Location
Northern Wi.
Your nose is the best detective here. Go to the end of a piece of insulation and separate it from the paper is there black stuff in between them? Also look at other wires see if they are doing that.
 
M

MikeF2316

Well-known member
Joined
Dec 29, 2012
Messages
9,605
Location
Thornhill, ON
That looks exactly like my attic. Electrical boxes too. My house was made in 1950, I would imagine this one is from the same era. My original wiring all has asphalt/cloth insulation, like the other wires in your picture. All my original wiring doesn't have a ground wire. :sad:
 
N

NUTTSGT

Super Moderator
Staff member
Joined
Sep 14, 2009
Messages
51,130
Location
Northern Central Ohio
Cmreschke said:
That box is being used correctly. The clamp is internal, notice the screw protruding between the top knockouts.
That box is designed for that.
Click to expand...

I was going to mention that also. You can also see the galvanized plate of the clamp in the slots of the knock out.


OP, if you have the skill and for peace of mind, since you are pulling back the insulation, you could run new wire.


EDIT: Now that I look back at those pictures, does the wire in question have a crease/groove down the center ? It almost looks like the wiring I pulled out of our landscaping for some outdoor (low voltage ??) lighting.
 
Last edited:
W

Whitworth

Well-known member
Joined
Dec 26, 2011
Messages
2,100
Kraft paper backing is acidic. That explains the discoloration, a chemical reaction with the wire jacket. Moisture may also have been present and accelerated the effect.
 
You must log in or register to reply here.
To avoid these ads, REGISTER NOW!
Top Bottom