Keter 7 Drawer Tool Storage System @ Sam's Club

[bcradio]

They had this 7 drawer tool chest on closeout at my Sam's club for $69. It's perfect for all my electrical test gear and connectors.

http://www.amazon.com/Keter-Drawer-Modular-Storage-System/dp/B00GQRCDA6

As always YMMV

 

[Azgdds]

My store shows $79. Will they price match with proof? What zip code are you?

 

[archirelic]

Sams here has it at 79 as well.

 

[bcradio]

No, they unfortunately won't price match closeout items... I'd hold out for a bit because they will likely come down more. $79 still isn't bad though.

 

[Dennis93]

The drawers are very narrow on this, no depth at all, so I passed.

 

[tadwolfe]

I bought one for computer repair and parts, plan on picking up one more before they are gone.

 

[Azgdds]

Saw it in store and passed also.

 

[bcradio]

Yeah these are definitely not meant for bulk tool storage, but rather miscellaneous little things are ideal for them.

 

[Mickey O]

I've got one of these units, like it a lot, did not like how hard the drawers were to open (especially when it's cold), pulled off the rubber detents (not needed as the drawers have a locking system) and I'm pleased with it.

 

[miketoo2]

Saw these at Sam's in omaha. Same price as OP.

 

[bimmerTEK]

I just got one for $69+ comes out cheaper than replacing the drawer guides and casters for my old blue point cart. I will used it as a maintenance cart and stored my Maxidas scanner that I used for service resets. Is fill up already with few items. It is perfect as an electrical cart to stored your scope, meters,leads and accessories but I already have my harbor freight cart as my diagnostic cart(it is little safer since i can lock it). If you need more space you will need 2 it seem like you can stack them up.

 

[miketoo2]

Down to $52.01 at my local Sams club. Need to figure out what the .01 in the price means.

 

[Mooniac]

I think the .01 is just a quick flag in their system to identify a clearance/close-out item.

 

[gm54210]

$52 is a fine price, but was yours imported from the UK? That's got to be worth another $100.

http://lancaster.craigslist.org/tls/4277165978.html

 

[navymech]

Worked at Sam's a few years back. Any price ending in a 1 is below the stores cost.

I saw this and passed. I usually like Keter items, this one just looked cheap. They had a cantilever tool box that looked nice for around $30 with lots of compartments, I just have no use.

 

[CDD]

but was yours imported from the UK? That's got to be worth another $100.

Each drawer is filled with

So you know is worth every penny!

 

[Farmall450]

They look like they'd make a decent cart too.

 

[bcradio]

Worked at Sam's a few years back. Any price ending in a 1 is below the stores cost.

I saw this and passed. I usually like Keter items, this one just looked cheap. They had a cantilever tool box that looked nice for around $30 with lots of compartments, I just have no use.

These are definitely not cheaply made by any means. They are great quality, but are sort of a niche box. Not really usable as standard tool storage, but great for things like storing your electronics lab gear (my use), etc.

I put my meters in it, shrink tubing, connectors, wiring, test leads, and other similar items.

 

[TJJP77]

I snagged one of these yesterday for $69 at my local Sam's Club. Very nice for the price!

 

[miketoo2]

Pic attached

 

[W_KY]

Saw this at SAMs today for $44 but passed. Think I may go back and grab tomorrow