To avoid these ads, REGISTER NOW!

Porch Post Base Water Damage Options

Ryanbabz71

Well-known member
Joined
Jan 24, 2016
Messages
492
Not the best design having wood/composite type material on the concrete finishing off the porch post. The post itself isn't rotted but some of the "trim" pieces are damaged due to water getting on the concrete and the wood sitting on the concrete.

Anyone have any suggestions how to correct this or make it look nicer? Have seen pvc/brick wraps mainly for 6x6 posts. These are 4x4. Also seen actual brick not sure if I have enough room on the ends to pull this off.

b0f9906aa22e1d0489da21ec55777770.jpg


Example of the ends (4 total posts)

40c8f802a96bb85f98cf49d02398cbe8.jpg


Other posts (2 total)

ab9a3f47c20ff2313ce903264188a760.jpg


Best overall photo of the porch I have on my phone


Sent from my iPad using Tapatalk
 
To avoid these ads, REGISTER NOW!

Dirtydan69

Well-known member
Joined
Nov 8, 2015
Messages
847
Location
San Tan Valley, AZ
Use the galvanized post bases like the use for decks. Then when you install the collar trim around the bottom hold it up 3/8" to 1/2" off the concrete. If you can't stand the gap the caulk it. Make sure you caulk the top edge also. Leaving a weep hole would be a good idea too.
 

larry4406

Well-known member
Joined
Jan 27, 2006
Messages
19,564
Location
Northern Virginia
Use the galvanized post bases like the use for decks. Then when you install the collar trim around the bottom hold it up 3/8" to 1/2" off the concrete. If you can't stand the gap the caulk it. Make sure you caulk the top edge also. Leaving a weep hole would be a good idea too.

+1

On the porches we build similar to these, we use the post anchors and then the post trim. Our post trim is typically PVC or fiberglass.
 

Attachments

  • Post Anchor.jpg
    Post Anchor.jpg
    6 KB · Views: 30
OP
R

Ryanbabz71

Well-known member
Joined
Jan 24, 2016
Messages
492
I don't need to replace the posts themselves just the trim wood around them.


Sent from my iPad using Tapatalk
 

Bottlecapdigger

Well-known member
Joined
Dec 29, 2015
Messages
543
Location
Ontario
I did what Larry shows. Even used a SS lag into the concrete. Then use PVC to cap and cover the galvanized base. Use caulking to seal and keep out water and insects. Done. BCD
 

theoldwizard1

Well-known member
Joined
Feb 22, 2011
Messages
43,250
Location
SE MI
If possible, cut about 1" off of the base of the post. Slip a PT 1by under the post. Size it so that it is about 1/2" bigger in all direction than the post and the trim. Replace the trim and paint.
 

lakeroadster

Well-known member
Joined
Jan 19, 2015
Messages
5,166
Location
Central Colorado
The post itself isn't rotted but some of the "trim" pieces are damaged due to water getting on the concrete and the wood sitting on the concrete.

We had the same issue at our last home.

It had the galvanized stand off so, as you mentioned, the actual structural post was fine, just the lower trim looked bad from wicking in water.

What we did was removed the lower trim pieces. Then cut back the 4 sided post fascia pieces so they were about 2 inches off the concrete, then replaced the lower trim pieces with composite decking material, then painted the decking to match the column trim.
 
Last edited:
To avoid these ads, REGISTER NOW!

chaosracing

Well-known member
Joined
Nov 14, 2015
Messages
585
Location
Kutztown, Pa
Lowes sells both Azek and Royal pvc trim. The Royal is cheaper than the Azek, and it comes smooth on one side and wood grain on the other side. You can get screws and pvc plugs to hide the screws and then paint over them to match your posts, or whatever color you like. No special tools needed. You use the same wood working tools you would use with wood trim.
 

dfiler2

Well-known member
Joined
Dec 15, 2014
Messages
2,859
Location
NW Minnesota
Either replace the trim with PVC or find some cement siding scraps, make your own trim pieces and paint. Also, if the post covering, behind the bottom trim, goes all the way down, I would trim that by 1/2".
 

kbs2244

Well-known member
Joined
Nov 11, 2006
Messages
14,065
I would go with the remove and replace with plastic idea,
but what does the exposed "end grain" look like on those plastic boards?
 

johnyg

Well-known member
Joined
Nov 11, 2015
Messages
319
Location
boca raton fl
does pvc move like pt ??? maybe you could get away with miters. i did a pt base like that and left it 1/4 inch bigger so it floats..... water drains ,air circulates and when he hits it with the leaf blower any trapped stuff can come out. doesnt look to bad either like a shadow line. good luck....john.
 

alexb2000

Well-known member
Joined
Feb 7, 2010
Messages
664
Location
Fort Worth, TX
In addition to the above solutions the basic problem IMO is that the trim doors etc. all get hung or installed and then painted. I bet when you pull that trim off the bottom and back is bare wood. So common on homes today.

We used to have to prime all the hidden surfaces, cuts, etc. Everyone was carrying around a can of spray can primer in their nail bag.
 
To avoid these ads, REGISTER NOW!
Top Bottom