To avoid these ads, REGISTER NOW!

Proto Tools Picture Thread - Post Yours!

S

Smokeshow69

Well-known member
Joined
Dec 7, 2012
Messages
8,366
Location
Pacific Northwest
Garcky said:
Thanks! Looks like it doesn't exist. So, I'm stuck with 5/16-5/8 in three wrenches. I'm good with that. Really! All three are pocket wrenches, and very useful on older SAE stuff.

The 7/16 x 1/2 one has always been my favorite hand tool of all time. I pretty much always had it in my pocket. That way, I always had those sizes instantly at hand. From battery terminals to radiator fan bolts, you always seemed to need one or the other size. Both 7/16" and 1/2" were the 10mm of those old days. There never was one when you needed it.
Click to expand...
I totally understand your perspective about the sequential sizes not being available. In general craftsman offered alot less variety in terms of wrenches and so their sizes were sequential and you couldn’t really mix and match wrenches to create a set custom tailored to your specific use. Plomb/ Proto offered a lot more variety and different configurations of bolt openings in their wrenches and sometimes they didn’t offer sizes you would think they would. It’s odd but as you can see from the catalog, that’s what they did
 
To avoid these ads, REGISTER NOW!
G

Garcky

Well-known member
Joined
Sep 10, 2022
Messages
3,434
Location
Twin Cities Metro Area, Minnesota
Smokeshow69 said:
I totally understand your perspective about the sequential sizes not being available. In general craftsman offered alot less variety in terms of wrenches and so their sizes were sequential and you couldn’t really mix and match wrenches to create a set custom tailored to your specific use. Plomb/ Proto offered a lot more variety and different configurations of bolt openings in their wrenches and sometimes they didn’t offer sizes you would think they would. It’s odd but as you can see from the catalog, that’s what they did
Click to expand...
Yup. Well, really, I guess 3/4" is a little large for stubby wrenches, anyhow. The smaller three, though, are perfect. Looking at that catalog list, though, they even had some 32nd inch sizes in the small range. I've never had any need for those, aside from 11/32", which was pretty common on the nuts used to hold radio components that have a knob on them. But I had a hollow nut driver for those, so...
 
F

four.cycle

Well-known member
Joined
Oct 19, 2015
Messages
28,553
Location
Tacoma, Washington
@Garcky
I've been watching this.
I think the 3/4" size is a bit of an outlier.
GILLER made one - a 5/8" x 3/4" short offset double-end box wrench - 2120S
There is no equivalent in Thorsen. The Thorsen model 2120 is a 5/8" x 11/16" (as is the Giller model 2120)
oddball.
not surprised that Proto didn't make one.
 

Attachments

  • Giller 2120S 5.8 x 3.4 short 45 offset double-end box wrench 01.jpg
    Giller 2120S 5.8 x 3.4 short 45 offset double-end box wrench 01.jpg
    306.8 KB · Views: 99
  • Giller 2120S 5.8 x 3.4 short 45 offset double-end box wrench 02.jpg
    Giller 2120S 5.8 x 3.4 short 45 offset double-end box wrench 02.jpg
    310.7 KB · Views: 21
  • Giller 2120S 5.8 x 3.4 short 45 offset double-end box wrench 03.jpg
    Giller 2120S 5.8 x 3.4 short 45 offset double-end box wrench 03.jpg
    382.3 KB · Views: 13
G

Garcky

Well-known member
Joined
Sep 10, 2022
Messages
3,434
Location
Twin Cities Metro Area, Minnesota
four.cycle said:
@Garcky
I've been watching this.
I think the 3/4" size is a bit of an outlier.
GILLER made one - a 5/8" x 3/4" short offset double-end box wrench - 2120S
There is no equivalent in Thorsen. The Thorsen model 2120 is a 5/8" x 11/16" (as is the Giller model 2120)
oddball.
not surprised that Proto didn't make one.
Click to expand...
Yeah, I think you're right. I do have a old Craftsman -V- stubby offset DBE at 5/8 & 3/4m like that Giller. So, that one got added to my set, but I was hoping that Proto had made the 11/16 & 3/4 version, so I would have no duplicate sizes. Of course, a 6" long wrench isn't going to do much good with any fastener with a 3/4 head, anyhow, so no worries.

Thanks for the reply!
 
R

Ricky Joe

Well-known member
Joined
Sep 15, 2013
Messages
2,452
Location
Roanoke, Va.
Mintgrun said:
I have one of the 1131 3/4" x 5/8" wrenches you mentioned above. I agree that it should be 3/4" x 11/16" to go with the other ones. I wonder why they made it this way.
1669134418583.jpeg
Click to expand...
3/4” and 5/8” were very popular sizes. Off the top of my head, the only 11/16” size I can remember on older cars was Ford flathead head bolts.
 
O

Oldtuleguy

Well-known member
Joined
Nov 4, 2017
Messages
10,453
Did some work on toolmobile today. Found some 7/8 rollers for the drawers at the hardware store. A few spot welds fixed the loose drawer front.

20221205_160656.jpg20221205_155018.jpg20221205_150522.jpg
 

Attachments

  • 20221205_150427.jpg
    20221205_150427.jpg
    806.9 KB · Views: 10
O

Oldtuleguy

Well-known member
Joined
Nov 4, 2017
Messages
10,453
Yup I figure it's worth fixing. Just a heads up jims engine decals now has the correct 7 1/8" decal for these

20221204_095808.jpg
 

Attachments

  • 20221204_095821.jpg
    20221204_095821.jpg
    541.7 KB · Views: 8
S

Shelbylex

Well-known member
Joined
Jan 20, 2018
Messages
3,102
Location
MA
OldTuleGuy, do you think those rollers are as strong as the metal ones? (thinking as I need few rollers for my Red Rover...)
 
W

Woods_Wanderer

Well-known member
Joined
May 31, 2020
Messages
174
Location
Virginia
I only have a few Proto tools and they are all users not collectors, but here's my Proto 6006A. It's my only 3/8" torque wrench, got it at an estate sale.
I just got it back from calibration, still passes just fine!

20221208_173948.jpg
 
To avoid these ads, REGISTER NOW!
G

Gwizjames

Well-known member
Joined
Dec 29, 2021
Messages
50
“MFD USA” on a tapered/alignment punch. No other name brand. Satin finish. Could it be Proto?
Seems all the examples I see of MFD also say Proto. I did not look for a part number.
Who else might you suspect as the manufacturer?
James.
 
S

Smokeshow69

Well-known member
Joined
Dec 7, 2012
Messages
8,366
Location
Pacific Northwest

Attachments

  • 4CB72D2F-0AF5-4D95-A7DA-E0E7B318F400.png
    4CB72D2F-0AF5-4D95-A7DA-E0E7B318F400.png
    2.4 MB · Views: 21
  • E932F432-870D-48E0-96CA-B319CA1E1D74.png
    E932F432-870D-48E0-96CA-B319CA1E1D74.png
    2.5 MB · Views: 19
V

Vintagenut

Member
Joined
Dec 16, 2022
Messages
18
Proto compression tester - 1960's? It still works great. The red hose is Snap-on.
 

Attachments

  • IMG_0368.jpg
    IMG_0368.jpg
    962.5 KB · Views: 29
S

Smokeshow69

Well-known member
Joined
Dec 7, 2012
Messages
8,366
Location
Pacific Northwest
Speaking of screwdrivers, here is my 2 Proto la boards currently. Interesting that they have both the older wood handle design as well and the first generation bet’rgrip plastic handle drivers present . I think the wood handle drivers with metal caps held up to abuse longer which is why the wood ones where sold for so long after the plastic ones were introduced
 

Attachments

  • 3919325A-E81E-4552-AC17-D15AD4F7E9EF.jpeg
    3919325A-E81E-4552-AC17-D15AD4F7E9EF.jpeg
    897.3 KB · Views: 19
  • 1920B8C0-9741-4E4C-9380-161EB42944FA.jpeg
    1920B8C0-9741-4E4C-9380-161EB42944FA.jpeg
    802.2 KB · Views: 18
S

Smokeshow69

Well-known member
Joined
Dec 7, 2012
Messages
8,366
Location
Pacific Northwest
I got a few things today from four.cycle. Super excited! And the 202 thin nose pliers are in used and in mint condition! So cool. Also the 8” modern adjustable is made by western forge and probably looks similar since they made craftsman tools(apex/danaher tool corp).
 

Attachments

  • 5C168C75-E3F8-42AC-B7D4-21DCEBF9A020.jpeg
    5C168C75-E3F8-42AC-B7D4-21DCEBF9A020.jpeg
    1.1 MB · Views: 24
C

Car hobby

Well-known member
Joined
Nov 9, 2012
Messages
75
Location
DFW,Texas
These are a few Proto screw drivers from the early 1950s. They belonged to my grandfather. They are marked:
Proto 9688 8” #4 Phillips
Proto 9604 4” Flat
Proto 9684 4” #2 Phillip
Proto 2”
Proto 9704 4” Flat
 

Attachments

  • Screwdriver 1.jpeg
    Screwdriver 1.jpeg
    1.1 MB · Views: 14
You must log in or register to reply here.
To avoid these ads, REGISTER NOW!
Top Bottom