Pry bar locker help

[youngridge]

I have been itching to get one of these for a long time, I have read up on some of the sunex ones on amazon, and some of the reviews say they dont have lips on the top for attachment, that you bolt them on. Id prefer a lip on top if they make them, how do you guys mount yours? And where is the best place and brand to get? Thanks!

 

[chipper]

Mine is bolted on..I geuss it depends on what you buy and what cart you have...I have the HF 5 drawer cart and had to drill new holes but I think the 4 drawer you can use the existing bolt holes and there is a lip(I cut mine off) but its not made to hang and no support...if no one else post pics I'll go out and take one

 

[PnHmech]

The snap on one I had had a lip, and bolt holes, don't know about the new ones


Sent from my iPhone using Tapatalk

 

[youngridge]

Thanks guys, it would be going on the masterforce 44"

 

[pburressiii]

My snap-on also has holes and a lip. I opted to use the holes to mount it.


Sent from my iPhone using Tapatalk

 

[AndrewV]

The one i have, has a lip for mounting support.
Cheapest online right now is here

 

[youngridge]

The one i have, has a lip for mounting support.
Cheapest online right now is here

Is that the one you have Andrew?

 

[1950mercury]

My mac has a lip

 

[dankicksass]

I have the bigger Sunex, it has a flat lip.

 

[ibedayank]

The one i have, has a lip for mounting support.
Cheapest online right now is here

that is a tiny one...

26 holes in this one and has a lip with boltholes
http://www.globalindustrial.com/p/tools/tool-storage/carts/Sunex-large-locking-screwdriverpry-bar-holder-for-service-cart-red?infoParam.campaignId=T9F&gclid=COLQn5y1n70CFVFp7AodWAoAyQ

 

[AndrewH]

that is a tiny one...

26 holes in this one and has a lip with boltholes
http://www.globalindustrial.com/p/tools/tool-storage/carts/Sunex-large-locking-screwdriverpry-bar-holder-for-service-cart-red?infoParam.campaignId=T9F&gclid=COLQn5y1n70CFVFp7AodWAoAyQ

I've also been looking for a solution to hold my 8 pc Mayhew set (3 pc straight and 5 pc curved sets). I thought I had heard the one you linked could only be secured with bolts? Is there a non locking version with a lip? No one but me uses my garage so I don't have to worry about them walking off.

Thanks,
Andrew

 

[AndrewV]

Is that the one you have Andrew?

I bought mine from tool topia.
here is the exact one.

 

[AndrewV]

that is a tiny one...

26 holes in this one and has a lip with boltholes
http://www.globalindustrial.com/p/tools/tool-storage/carts/Sunex-large-locking-screwdriverpry-bar-holder-for-service-cart-red?infoParam.campaignId=T9F&gclid=COLQn5y1n70CFVFp7AodWAoAyQ

Exact same one as listed above. Mine is a sunex.

 

[youngridge]

Hey guys, thanks for the help, I appreciate it alot!!!

 

[rsanter]

Why is the lip important?
Don't you want it secured to the box?
If you want to keep the holes small then use pop rivets
If you don't want to put holes in the box then take flat meterial and drill it to match the holes for the handle of the toolbox and then attach the holder to that

Bob

 

[ibedayank]

Exact same one as listed above. Mine is a sunex.

I did this at home only I use the tools
chunk of scrap aluminum angle and a hour of time