Question from Toptul (Mike Wren)

[The Muffin Man]

Mike, would you also offer the socket sets alone without the tray for those who already have the Hansen trays?

 

[66HertzClone]

Looks like one to me, I remember the best print ad I ever saw had an M5 in it. A rear photo of the M5 with four people in it, if I remember correctly it had just gone over a rise or railroad track crossing. All four wheels were off the ground, it just seemed to be floating there.

 

[amishman]

Mike, would you also offer the socket sets alone without the tray for those who already have the Hansen trays?

I would 2nd that one. Complete sets without the trays. I already have a decent socket holder so.

I would dig a complete MM satin finish 1/4, 3/8, and 1/2 sets with regular and deep.

tj

 

[wrenhandtools]

yes, if I'm honest, I would rather sell without the tray so I don't have to ship or inventory them......unless I find that the price being charge on average is a lot higher than what I would charge.

 

[fordracing200]

I personally think you should sell your own trays to put the sockets on and include them with the sockets....that'd be the easiest.

 

[JeepsAreBuilt]

I'm thinking..complete..comprehensive sets, in deep, shallow, 6pt, 12pt, mm, inches, chrome and satin......

Hrmm.. I'm thinking I'll get chrome for SAE then satin for metrics.

 

[trackwelder]

No interest either way.

 

[Joelfke]

No interest either way.

then...why comment...

 

[trackwelder]

then...why comment...

Because the OP asked a question. I don't recall in this thread that only interested parties could comment.

 

[Diesel_Crawler]

Because the OP asked a question. I don't recall in this thread that only interested parties could comment.

As funny as this is, you are correct.

 

[Joelfke]

mhmmmmm

 

[Stephenw]

im kinda getting sick of the "not made in USA then it must be ****" theory...

Reading comprehension much?

Let me simplify…

I said I’m not sure if I’d buy imported hand tools, but if the website worked, I might be tempted to give them a try.

The buttons that give prices and allow orders to be placed do not appear to work.

:angryflipoff:

 

[Joelfke]

Reading comprehension much?

Let me simplify…

I said I’m not sure if I’d buy imported hand tools, but if the website worked, I might be tempted to give them a try.

The buttons that give prices and allow orders to be placed do not appear to work.

:angryflipoff:

jesus calm the f@ck down it was already cleared up

 

[Stephenw]

jesus calm the f@ck down it was already cleared up

If you were making a general statement about people calling import tools ****, you should have just made the statement. You should not have quoted me when making such a statement.

 

[wrenhandtools]

Stephenw,

uh yeah, it says right on the home page that they don't work yet. Sorry that it is not done yet. Most of the website does "work" by the way. I'm just a bit old school and like talking to customers vs every single thing being automated. It is BAD that you can't see the pricing right now, but that will be fixed in a while. If something interests you before then, you are always welcome to call. If not, no worries.

Sincerely,

 

[Merkava_4]

So far the site is looking real good Mike. Some of the price buttons aren't working yet, but I'm not worried about it. I was checking out that magnetic screwdriver that holds the bits.

 

[Garage_Mahal]

Hrmm.. I'm thinking I'll get chrome for SAE then satin for metrics.

Idea thief!

 

[Diesel_Crawler]

jesus calm the f@ck down it was already cleared up

What is not "calm" about that post? I think you need to cut back to less then 5 cups of coffee a day

 

[Joelfke]

What is not "calm" about that post? I think you need to cut back to less then 5 cups of coffee a day

lol perhaps