Quick Tool box Handle Question

[oldpops]

Well once again I turn to those here for a little help and advice! I have a large rolling toolbox that doesn't have any handles on the ends to pull/push. I have looked at the local big box stores and about all they have are flimsy handles that look more like towel bars than tool box handles (and they wouldn't last long considering the weight of the tool box). Either that or I get a handicap grab bar, which is a little too big to wrap my fingers around. Interestingly, even though they (the big box stores) sell tool boxes, there isn't really any provision for getting replacement handles. So I thought I would ask here. Anyone know or have a suggestion to mount on a metal rolling tool box. Again, thanks again in advance for all assistance and advice!

 

[Kaizen]

Well once again I turn to those here for a little help and advice! I have a large rolling toolbox that doesn't have any handles on the ends to pull/push. I have looked at the local big box stores and about all they have are flimsy handles that look more like towel bars than tool box handles (and they wouldn't last long considering the weight of the tool box). Either that or I get a handicap grab bar, which is a little too big to wrap my fingers around. Interestingly, even though they (the big box stores) sell tool boxes, there isn't really any provision for getting replacement handles. So I thought I would ask here. Anyone know or have a suggestion to mount on a metal rolling tool box. Again, thanks again in advance for all assistance and advice!

How much do you move it? How big? Are there no bolt holes already for handles? Personally i made the decision to have and use a pallet jack for everything. Much easier for me. If you can't weld something i'd be looking at sliding barn door handles

 

[Shiftless]

Would you consider this?

 

[Shiftless]

Or maybe this?

 

[BillK]

Either make your own or flag down a Snap On or other tool truck and ask them to order one for one of their boxes ?

Also you say there is no provision to order handles for the "big box" store units ? I bet if you get a model number for the tool box and then find the parts list online you will most likely be able to order a handle.

 

[Shiftless]

Why stop at a tool box handle?
Here is a door handle I fabbed up for a basement room crawl space access door.

 

[97tj-neil]

Would one of these work for you?

Safety Handle - Swing Set Accessories - The Home Depot

Get free shipping on qualified Safety Handle Swing Set Accessories products or Buy Online Pick Up in Store today in the Playground Sets Department.

www.homedepot.com

 

[kbs2244]

a quick and cheap answer would be a garage door lifting handle

Clopay Decorative Spade Lift Handle for Overhead Garage Doors 0125060 - The Home Depot

Amp up a comfortable addition to the garage doors in your home with the selection of this adorable and amazing Clopay Decorative Spade Lift Handle for Overhead Garage Doors.

www.homedepot.com

But I like the black pipe assembly for a heavier box


You will need access to the inside for the through bolts with large washers

 

[slowtwitch73]

Go to the fence hardware isle.. lots of options.

 

[oldpops]

Thanks everybody! I LOVE the box-wrench handle, and also the (1/2 inch or 3/4 inch pipe) ideas. Don't think my wife would allow either to be used doors inside the house, but I can assure you that they will be used a lot in my "area of influence". Thanks again!

 

[NUTTSGT]

The handle on my "Tool Shop" brand box from Menards would be easy to duplicate.

 

[Bill Bowman]

Why not just buy a brushed stainless "grab bar", like used for handicap areas?

 

[alinc100]

I have an unused handle from a U.S. General box. No mounting hardware. Your welcome to it for the $ of shipping.

 

[bubinga]

Why stop at a tool box handle?
Here is a door handle I fabbed up for a basement room crawl space access door.

Nice?

 

[bubinga]

Would one of these work for you?

Safety Handle - Swing Set Accessories - The Home Depot

Get free shipping on qualified Safety Handle Swing Set Accessories products or Buy Online Pick Up in Store today in the Playground Sets Department.

www.homedepot.com

Good options!

 

[bubinga]

Thanks everybody! I LOVE the box-wrench handle, and also the (1/2 inch or 3/4 inch pipe) ideas. Don't think my wife would allow either to be used doors inside the house, but I can assure you that they will be used a lot in my "area of influence". Thanks again!

Maybe even 1/4" or 3/8" pipe/elbows and floor flanges if they are available?

 

[bubinga]

I have an unused handle from a U.S. General box. No mounting hardware. Your welcome to it for the $ of shipping.

OP, that's "you"!

 

[oldpops]

What are the dimensions (of the handle) and do you know how much would it be to mail it to zip code 92530?