Reccomend an impact driver

[Big Bob]

I went to replace some of the popped up nails on my 30 year old deck with 3 1/2 inch deck screws and found my Bosch 12v lithium was NOT up to the task. Is there an impact driver anyone can recommend that would handle that task, or should I just pound the galv nails back in?

Thanks for your opinion. Have a good Memorial Day weekend.

 

[kramarj]

Milwaukee M18 gets my vote.

 

[BK13]

Pretty sure my M12 Fuel could handle it.


Sent from my iPhone using Tapatalk

 

[thebeekeeper1]

I too have a Milwaukee M18 (not a FUEL) and it will drive screws into concrete easily, so I'd bet it will do the job. Another guy found the drill and driver combo kit for $166 yesterday . . . I think at Homeless Depot.

Edit: Here's the thread--Sorry, but $170: http://www.garagejournal.com/forum/showthread.php?t=291720

 

[Sal Bandini]

That's why I keep one of these around.

 

[shampoop]

I'd imagine any of the top name brands 12v or 18v drivers would be up to the task.

The real question is, what system do you want to buy into and what other cordless tools might you want to buy? That would also determine whether you should go with 12v or 18v.

 

[mwwusa]

I went to replace some of the popped up nails on my 30 year old deck with 3 1/2 inch deck screws and found my Bosch 12v lithium was NOT up to the task. Is there an impact driver anyone can recommend that would handle that task, or should I just pound the galv nails back in?

Thanks for your opinion. Have a good Memorial Day weekend.

I have and like my Dewalt DCF885 impact driver. I just helped a friend redo his deck with 3" and 3.5" deck screws. The DCF885 was more than equal to the task.

The DCF885 is 20v but not brushless. Dewalt has two brushless models DCF886 and DCF895 that cost more and last longer on the same battery.

Get batteries that show their state of charge when you purchase. The dewalt 2.0 amp Hr, 4.0, and 5.0 all have this feature.

You'll be happy with any of these.

 

[paullie]

i have had really good luck with ryboi 18volt from home depot

 

[ADSR]

Pretty sure my M12 Fuel could handle it.

I've built some pretty big decks with mine. It doesn't even break a sweat. Very lightweight too.

 

[kctyphoon]

ANY 18 impact driver will do that just fine.. 12v impact can get it done (i have m12 and 12v max), but you cant compare them to an 18v impact.. i have the m18 fuel and non - fuel versions too.. the 12v stuff can do it, but your asking alot of them and the runtime will reflect that - the 18v stuff wont even blink - will drive screws in at twice the speed of a 12v. if you have a budget or preference of brands you should mention that also.. i think cpo has a good deal on an m18 drill / impact set going on if that intrests you.

 

[wrenchMONKEY_]

M18 Fuel gets my vote.
I have the 3/8 and 1/2 Fuel, but I'd like to get the M12 Fuel 3/8 for when I don't want such a big tool, but need a bit more power.

 

[RedRabbit]

Makita 18v lxt brushles. The best you can buy.

 

[Voi]

Bosch 12v lithium was NOT up to the task.

What's the model number of the 12V Bosch you have? If it's not the newer brushless model it's worth checking that one out.

Some online reviews seem to suggest it packs a lot more punch than its predecessor. If you have other tools on that system and like them I'd consider the brushless bare tool.

 

[kctyphoon]

Makita 18v lxt brushles. The best you can buy.

i agree that Milwaukee and Makita are the two top brands to buy right now - and i hate to admit this - but the Ridgid impact driver is on the top of the mountain for now as far a torque specs.. i still wouldnt buy it over my Milwaukee tools, but i think alot of people will like the new Ridgid stuff.

 

[txvwnut]

I've got an 18volt Ryobi impact driver it hasn't refused anything I've done with it.

 

[jd_1138]

I've got an 18volt Ryobi impact driver it hasn't refused anything I've done with it.

+++1. I am loving the Ryobi 18V One lineup. I have the impact driver, drill, circular saw, reciprocating saw, JobPlus multi-tool, flashlight, work lantern, and the jobsite radio. Once you buy into the system and have the charger and batteries, it's economical to add bare tools here and there or an occasional package with an extra battery.

And don't even mess with 12V, sure it MAY work but unless you're a pro carpenter, the weight savings by going with 12V is not worth it, IMHO.

I've dropped my Ryobi impact off 10 foot ladders and it still works perfectly.