To avoid these ads, REGISTER NOW!

Remodeling the 40x80 Vette Garage

VetteGarage

Active member
Joined
Oct 26, 2012
Messages
30
Location
Conroe, TX
Ironhorse on this forum said I should create a thread to show the remodel of my Vette garage. I bought the building from Ironhorse, and it is directly behind his shop. When I first put a contract on the building 3-21-12, it looked like this on the outside:

april42012036.jpg


april42012038.jpg
 
To avoid these ads, REGISTER NOW!
OP
V

VetteGarage

Active member
Joined
Oct 26, 2012
Messages
30
Location
Conroe, TX
Ironhorse's building and my building were on the same the plat, and it took until August to get it replatted and approved by the city. When we closed the deal on 8-8-12 the building looked like this:

233.jpg


231.jpg


228.jpg


226.jpg


225.jpg
 
OP
V

VetteGarage

Active member
Joined
Oct 26, 2012
Messages
30
Location
Conroe, TX
By 8-23-12 we had all of the old drywall removed, replaced rotten studs and added framing to make the walls 12' tall. Here are a couple of pictures:

239.jpg


240.jpg
 
OP
V

VetteGarage

Active member
Joined
Oct 26, 2012
Messages
30
Location
Conroe, TX
By 8-27-12 we had the top four feet of the walls insulated and drywalled. This was done first so we could start on the drop ceiling. We also put in the framing to pour concrete for a 13x30 building added on to store a boat in.

265.jpg


266.jpg


267.jpg
 
OP
V

VetteGarage

Active member
Joined
Oct 26, 2012
Messages
30
Location
Conroe, TX
On 9-24-12 one of the small entry doors has been removed and new metal siding has been added. The forms are in for the driveway into the boat storage. More ceiling tiles have been installed with R-30 insulation on top. Work is being done to turn the two small restrooms into one larger bathroom with a shower.

346.jpg


348.jpg


349.jpg


350.jpg
 
OP
V

VetteGarage

Active member
Joined
Oct 26, 2012
Messages
30
Location
Conroe, TX
On 10-21-12 we have R-30 insulation in all of the walls and the ceilings. The central air conditioning is installed. The first set of "insulated" rollup doors which will not seal air tight have been removed. Panel type garage doors with an R-17.5 rating have been installed and the outside of the doors has been painted.

538.jpg


539.jpg


540.jpg


541.jpg


542.jpg


543.jpg


544.jpg


545.jpg


547.jpg


548.jpg
 
OP
V

VetteGarage

Active member
Joined
Oct 26, 2012
Messages
30
Location
Conroe, TX
On 10-26-12 the wood on the store front is painted and the corrugated rusted tin is installed on the roof of the store front. The dry wall is all in and has been floated.

010.jpg


011.jpg


009.jpg


012.jpg


008.jpg


006.jpg


005.jpg


003.jpg
 
To avoid these ads, REGISTER NOW!

94legaleagle

Well-known member
Joined
May 7, 2009
Messages
294
what size of square posts did you use for the storefront UPRIGHTS?? 6x6, 7x7 or 8x8???? I like the size of them, and I'm going to be building a deck @ the lake next year, and I want to use upright posts that look the same size as yours do

NICE project by the way - also, what vettes? I've got a 2001 - you on the Corvette Forum?
 

Ironhorse

Well-known member
Joined
Sep 17, 2012
Messages
800
Looks so good....thanks for posting it!!!! I want to see it with cars inside!!
 
OP
V

VetteGarage

Active member
Joined
Oct 26, 2012
Messages
30
Location
Conroe, TX
Thanks for all the responses.

On the Corvette Forum I am 00Nassaur. I will have four Corvettes in the garage.

A 1960 retro-rod red with white coves with an LS2 engine and 6-speed transmission.

A 1963 project car I just bought. The original split window was removed and many original parts including the engine are gone. I am going to put the split window back in and retro-rod it. It will be my first project when the garage is done.

A 2000 Nassu Blue Convertible.

And a 2008 Jet Stream Blue Z06.

I am pretty sure the posts are 8X8's, but I will measure them the next time I go over to the garage. I measured them, and they are actually 6x6's.
 
Last edited:

Omphaloskeptic

Well-known member
Joined
Oct 11, 2008
Messages
2,346
Location
Ultima Ratio, Wa.
Very nice progress; can't wait to see it set up for the resto-rod work.

What was the story on the 'insulated' roll-ups? Did somebody have to eat the cost of the re-install of something that seals?
 
OP
V

VetteGarage

Active member
Joined
Oct 26, 2012
Messages
30
Location
Conroe, TX
I trusted the metal building sub-contractor when he said that what he recommended were the best insulated rollup doors. He knew I was installing central air. As soon as I saw the doors installed, I asked him how the doors were ever going to seal to make the heating and cooling of the building efficient. All he had to say was that they were insulated doors.

I then got with my main contractor and got the doors replaced with doors that sealed and have an R-17.5 rating.
 
OP
V

VetteGarage

Active member
Joined
Oct 26, 2012
Messages
30
Location
Conroe, TX
On 10-29-12 the interior doors are hung and the walls are blown and then the high parts were knocked down with what looks like a floor squeegee to give it a smoother finish.

IMG00002-20121029-1708.jpg


IMG00003-20121029-1710.jpg
 

BowtiePimp

Active member
Joined
Nov 1, 2012
Messages
25
Location
New Jersey
I may be way out but are you going to be living here also?? but awesome work I love the tin roof look always a classy touch!
 
OP
V

VetteGarage

Active member
Joined
Oct 26, 2012
Messages
30
Location
Conroe, TX
I can live there when the wife's pissed at me. :lol:

And I plan on spending a lot of time their when I retire in a couple of years.
 
Last edited:
To avoid these ads, REGISTER NOW!
Top Bottom