Show your new tool arrivals
- Thread starter sarel.wagner
- Start date
Almostbroke94
Well-known member
I recently got a new tool for making tools, tool organizers and just tooling around...
Sent from my Pixel 3a XL using Tapatalk
I just ordered the Ender 5. Chomping at the bit for it to show up.
Attachments
wkndwarrior29
Well-known member
This is my first venture into it, so each time I try new settings or a new print - it is like hours of torture until it is done and I can try the next configuration. I can see how people end up with a collection of these things. Good luck! If you haven't already, check out tiny machines website for firmware and accessories.
Sent from my Pixel 3a XL using Tapatalk
Its a steep learning curve upfront with 3D printing; but its smooth sailing once you get the hang of it.
If you haven't yet, switch to PETG, it prints like PLA but is durable like ABS, with an added bonus of being low VOC.
PLA absorbs water over time and is cracks under any kind of prolonged strain.
Just remember when printing; there is as much variation between colors as there is between filaments. Overture black PETG for example prints well at 255-260c whereas white at 230-240c (even though both indicate 230-240 on the packaging).
Coach James
Well-known member
dalehsc
ALLIANCE MEMBER
The modified socket in the upper right reminds me of one I made to screw out the petcock on the water trap at work. It's 8ft from the floor,a cut out socket & some extensions,and I can reach it.
Jack84
Well-known member
It’s says professional on the box so it must be good.
Looks good so far, beefy wrench with a good finish.
Sent from my iPhone using Garage Journal
Coach James
Well-known member
Did you do the cutout in stages to keep from heating the socket?
After reading your post, I went out to see the markings on that socket. All it has is "Truth Mannato 1". There is a symbol between the two words that looks similar to a Chevy symbol. The "Mannato" may be "Mankato". There is a scratch over the 4th letter so I'm not sure.
I did find this: http://alloy-artifacts.org/truth-tool.html
It would be interesting to know how old the socket is.
Coach
Last edited:
Farmall450
Well-known member
PelicanPines
ALLIANCE MEMBER
Snagged this shortly after "almost falling" off my cheap *** folding plastic POS from bed bath and beyond... while trying to access the top of the triple stack tool box... looking for a small container of oil.
upgrading
Well-known member
Solid.
USA or China ?
USA or China ?
PelicanPines
ALLIANCE MEMBER
EDITED:
Conflicting information on their website... this model is made in China but... their website says:
Little Giant produces ladders for the U.S. market in a 250,000-square-foot factory in Springville. The plant, which employs approximately 250 people, has eight double-sided robotic welding stations made by Lincoln Electric Co.
Still it's VERY solid. Needs two hands to close and open (not a problem). NICE wide steps. FOLDS nicely. Safety handle has some nice features. Not very heavy to carry... not awkward either. Not sure where I will store it... I will photo it when I decide.
Positive clicks/locks, no holidays in the metal, all rivets and moving parts are solidly attached. hmm... Bugs me, they say USA on their website but Kudakev correctly pointed out that model is China...
Last edited:
kudakev615
Well-known member
- Joined
- Jan 10, 2017
- Messages
- 174
https://www.littlegiantladder.com/collections/ladders/products/safety-step-ladder
might wanna clink that link and scroll down to COO
might wanna clink that link and scroll down to COO
PelicanPines
ALLIANCE MEMBER
Huh... well... I copied my text right from their website... Ladders for the US market are made in the USA... hmmm... there are two models 300lb capacity and 375lb... wonder if there is a difference there.
Not worried... it's not my first LGLadder and I'm very happy with this one. I got it as a Amazon Warehouse Deal... it's regularly $106... I think it was $84.
QVC has the heavier duty for $99 with 5 payments of $20 (if the deal is still available)
I will update my post. Thanks
PelicanPines
ALLIANCE MEMBER
Agree... this is my 5th Little Giant Ladder. (this is the shortest, 2 steps) I have never had a single issue with any of them.
I am shocked tho/still about the China thing. Website touts their USA manufacturing plant yet... get this... every single ladder I searched for was made in China... all of them... every single model. Did we lose to China recently or was this all along? I need to look at the COO printed on my existing 4 ladders.
JoeMcGov
Well-known member
We did build a 2nd BIGGER Panama Canal to get more of their goods to 'Merica.
Qualitytools
Well-known member
I have had mine for over 20 years no problem it's solid but heavy
Bighead38
Well-known member
I use the grease gun every day. I put a lock n lube coupler on it and love it. Makes greasing the machines so much easier.
PelicanPines
ALLIANCE MEMBER
My 2 old ladders are USA made. my 3 newer ones are CHINA.
In 2013 Little Giant Ladder was warned by the FTC to STOP advertising "Made in USA" as three different manufacturers in China make their products.
Rant OVER. This email was to clarify tool quality and COO... something that is commonly discussed... Please move on.
I am happy with my new ladder. It has garnered a place of honor next to my 3 stacks of triple stacks. New tools have been ordered and will be visualized here shortly.
MikeH
Well-known member
New arrivals from just down the alley, where these had been abandoned in a trash pile. Sadly all standard (I could better use a second set of metrics), but all in good condition, and besides they brought their own storage. 1/4 and 1/2 are all Craftsman and all EE, for whatever that’s worth. 3/8 are a mix, I guess he used, lost, and replaced those most often.
Last edited:
PelicanPines
ALLIANCE MEMBER
New arrivals from just down the alley, where these had been abandoned in a trash pile. Sadly all standard (I could better use a second set of metrics), but all in good condition, and besides they brought their own storage. 1/4 and 1/2 are all Craftsman and all EE, for whatever that’s worth. 3/8 are a mix, I guess he used, lost, and replaced those most often.
I fixed your link in my post... by taking out the S ... in the HTTPS
Nice get... i love those rails.
MikeH
Well-known member
Thanks. If I ever learn how to link pictures correctly on the first try they'll just change the platform again!
Picked up a set of German VDE screwdrivers since I discovered I was missing a small flat tip while installing a ceiling light. Also got my 3/8" in 1/4" body Nano ratchet as part of the Astro BOGO deal a few weeks back. And finally a cheap set of JIS screwdrivers from Amazon for the Honda.
Attachments
dalehsc
ALLIANCE MEMBER
Strength wasn't a need for the socket. Took a die grinder & ground two notches in it. It was an old 12pt rusted socket from an estate sale,if it wasn't used for this it was destined for the scrap pail...lol
wkndwarrior29
Well-known member
Thanks for the tips, I'll start dabbling with new materials once I am consistent and get the hang of printing supports. I've also learned that a good number of the free designs out there are dimensionally off!
Sent from my Pixel 3a XL using Tapatalk
Fedwrench
ALLIANCE MEMBER
received a few Koken "High Performance Tools of Convincing Quality" today.
3/8 semi deep six point socket set 7-19 mm and added to my universal nut grip selection with 7, 8. & 13 mm. i already had the 10 mm.
Got everything from Palmac Tools. Mr Subaru 1387 on you tube has a 5% discount code. 5% might not be much but, it's better than a sharp stick in the eye.
3/8 semi deep six point socket set 7-19 mm and added to my universal nut grip selection with 7, 8. & 13 mm. i already had the 10 mm.
Got everything from Palmac Tools. Mr Subaru 1387 on you tube has a 5% discount code. 5% might not be much but, it's better than a sharp stick in the eye.
Attachments
received a few Koken "High Performance Tools of Convincing Quality" today.
3/8 semi deep six point socket set 7-19 mm and added to my universal nut grip selection with 7, 8. & 13 mm. i already had the 10 mm.
Got everything from Palmac Tools. Mr Subaru 1387 on you tube has a 5% discount code. 5% might not be much but, it's better than a sharp stick in the eye.
Those look like a nice metric set, Fed. Can I ask cost of just the metric socket set? Thanks.
Sent from my iPhone using The Garage Journal mobile app
Farmall450
Well-known member
Held a jack stand for a semi mounted plow while I ground out and welded it up last night...so far so good.
received a few Koken "High Performance Tools of Convincing Quality" today.
3/8 semi deep six point socket set 7-19 mm and added to my universal nut grip selection with 7, 8. & 13 mm. i already had the 10 mm.
Got everything from Palmac Tools. Mr Subaru 1387 on you tube has a 5% discount code. 5% might not be much but, it's better than a sharp stick in the eye.
The zeal sockets are 10/10 would buy again.
Snagged this shortly after "almost falling" off my cheap *** folding plastic POS from bed bath and beyond... while trying to access the top of the triple stack tool box... looking for a small container of oil.
I've had one of those for at least 20-25 years I think. It is rock solid.
What I get the most use of is their Flip-N-Lite. Super handy around the house.
old_smokey
Well-known member
Thanks to Garage Journal I learned all about buying tools off Amazon in different countries...
Working on mostly old Japanese motorcycles means lots of JIS, so I bought a pile of Vessel and a couple SunFlag screw drivers off Amazon Japan, as well as some off japan.webike.net
I picked some up for my moto friends as well. The initial pile was rather large.
Removing the stuff my friends bought left me with my personal order:
Full set of Megadora Jawsfit screwdrivers, set of 4500-series heavy duty screw drivers, a few ball grips, #1 and #2 Impactas, #1 and #2 SunFlag JIS drivers, small and regular ratcheting screwdrivers, some KTC mini drivers, and some master cylinder deep 90 circlip pliers.
There is much talk here on whether the Megadora line of screwdrivers are actually JIS vs some close DIN standard. The 4500 and SunFlags are definitely JIS though. I can’t discern any difference in fit between all three. They’re all perfect.
Sent from my iPhone using Tapatalk
Working on mostly old Japanese motorcycles means lots of JIS, so I bought a pile of Vessel and a couple SunFlag screw drivers off Amazon Japan, as well as some off japan.webike.net
I picked some up for my moto friends as well. The initial pile was rather large.
Removing the stuff my friends bought left me with my personal order:
Full set of Megadora Jawsfit screwdrivers, set of 4500-series heavy duty screw drivers, a few ball grips, #1 and #2 Impactas, #1 and #2 SunFlag JIS drivers, small and regular ratcheting screwdrivers, some KTC mini drivers, and some master cylinder deep 90 circlip pliers.
There is much talk here on whether the Megadora line of screwdrivers are actually JIS vs some close DIN standard. The 4500 and SunFlags are definitely JIS though. I can’t discern any difference in fit between all three. They’re all perfect.
Sent from my iPhone using Tapatalk
Attachments
Last edited:
sweet victory
Well-known member
Picked up a few small things. Super stoked to have The German Tool truck visit every other week, so I'll get to check out a lot of Koken, Tone, and Stahlwille tools.
First up is Koken double swivel 1/4" joint.
Koken 19mm Wheel Socket
AST Transmission Fluid Fillter
SO Tire Tread Depth Gauge. Far easier to read than the "pen" style
First up is Koken double swivel 1/4" joint.
Koken 19mm Wheel Socket
AST Transmission Fluid Fillter
SO Tire Tread Depth Gauge. Far easier to read than the "pen" style
sweet victory
Well-known member
Holy Smokes Old Smokey...you seem like a good friend to have!
old_smokey
Well-known member
I should clarify!! I didn’t buy all those tools for them out of my own pocket. My post sounds a bit misleading after re-reading it. I just coordinated a group buy so we could all benefit from super cheap shipping.
Sent from my iPhone using Tapatalk
