Sliding compound mitre saw

[sharpshooter]

anybody ever used this saw http://www.sears.com/shc/s/p_10153_12605_00921237000P
If so can you tell me about it. I really wont use this saw that much to warrant spending 400+ dollars on one.... maybe a few times a year. Im also looking for a good table saw and cordless 18 volt drill. I have some sheetrock to hang and some workbenches to make.

 

[heelsroll]

Sharpshooter, I picked one up when they were on even deeper discount. All I've had time to do is unpack, align, and square, but it seems well enough made. Definitely Hecho en China if that bothers you, but not bad. There are a ton of complaints on Sears.com about the handle breaking but it seems sturdy enough to me.
I've put in thousands of cuts on this one's stationary brother, installing hardwood and laminate flooring, and have no complaints for those uses.
This one squared up quickly and easily and all the motions seem fine. Power users will probably immediately replace the blade but I'll tear it up with some laminate first. The laser is powered by the saw, not a battery like the older models.
Let me know if you have any specific questions or I can cut some test boards if you need. But I'd say it's hard to beat the price for what it gives you.
Best,
J

 

[Dr.JohnnyFever]

I don't know anything about that saw in particular.

However, if you are planning on getting a good table saw later, have you considered getting a non-sliding mite saw?

 

[Dr.JohnnyFever]

I have this non-sliding Makita:

It is approx $100 more than the Craftsman slider but is great quality.

The specs say at a 45 degree bevel it will cut 1-3/4" x 5-1/2".

At 90 degrees 3-7/8" x 6".

I have never found it unable to cope with the width of anything I need to cut but I have never worked with truly gigantic crown molding and the like.

 

[crowldawg]

I have one of the above as well .It really depends on what you are going to cut (size).A stationary 10 in saw will not fully cut a ?x 6 unless you tilt the board ,and you can't tilt the board unless you remove the guard. I do most of my cutting with a 12 in dewalt compound slide saw .I use the makita for something quick, I hope the saw you buy has an aluminium frame because I also have my old 10" makita .its made of cast iron and that never leaves my shop.
I have a 10 in makita table saw .Its indestructible .I throw it in the back of my truck every day and I have no idea the number of houses its been involved with.
Dewalt 18volts

 

[Junkman]

I have a 12" DeWalt compound mitre saw, and it is great. I would be checking Craigslist for a used one if you have no adversion to saving money. I bought mine used, and it looked like new. I saved about 40% of the best price that I could find in any of the stores. Same for my 18 volt DeWalt drill. Once you own it for a few months, it is a used too anyway. Everyone drives on used parts......

 

[JayL]

Anybody have this model ? Not sliding but to me the price looks reasonable ..

http://www.amazon.com/exec/obidos/t...t_shr?_encoding=UTF8&m=ATVPDKIKX0DER&v=glance

 

[Dr.JohnnyFever]

Doh! I forgot to note that my Makita is a 12" and the model is LS1221.

Makita LS1221 at Amazon

 

[sharpshooter]

I guess I could just get a non-sliding miter saw ( maybe could get a little more pricier one) since Im gonna be getting a table saw anyways.....

 

[JayL]

In my experience buying power tools I have never had any bad experience with Makita at all (although I have not tried their Miter Saws). In the end I always got my money's worth.

 

[Benchloader]

I have that same Craftsman 10" Sliding Saw. Fits my needs well as it is portable and I can take it to my job site. You need clearence behind the saw for the arm. Does a good job for me on 2 x 8's, and wider (up 11 3/4) boards. The 60 tooth blade makes pretty nice cuts for me, very little tearing on thick boards. I use it as a compliment to my 10" Compound Miter saw for larger boards. Not bad for the price (sale price that is).

 

[dxdexter]

I have a Makita 10" dual sliding compound miter saw and would highly recommend this model. Unless you intend to cut 6" x 6" then the 10" model should suffice, otherwise go with a 12".

The Makita will compound in both directions where many other models will not. If I were you I would spend the extra cash and go with a slider. You will not regret it, but you may regret not getting it. It is much more versatile.

A table saw will not make up for lack of a sliding miter saw. They are much more difficult to get proper setups and you have to move the material, which is much harder than holding the material and moving the blade. there is less chance of error.

 

[l_bilyk]

As far as sliders go, i would probably look at the makita or the bosch

 

[PAToyota]

I'm very pleased with my 12" (non-sliding) DeWalt.

 

[sharpshooter]

Maybe i dont really need a slider, Im gonna be making a workbench and some shelves. I cant justify spending a great deal of money on that type of saw when a single bevel compound would prolly do the trick just fine. Damn, I love buying tools but hate spending money, LOL

 

[Dr.JohnnyFever]

A table saw will not make up for lack of a sliding miter saw. They are much more difficult to get proper setups and you have to move the material, which is much harder than holding the material and moving the blade. there is less chance of error.

A table saw will not make up for the lack of a *compound miter* saw. However, the sliding feature is entirely optional based on the expected maximum stock dimensions.

For simple (not compound) miters, don't underestimate the utility of a good cross-cut sled with a table saw. I made one for my Unisaw out of birch ply and red oak that was joy to use.

However, if you are going to be installing a bunch of molding then the CMS wins.

Another data point - I had the 12" Dewalt CMS and sold it and got the 12" Makita CMS. YMMV but I think the Makita is better.

 

[sharpshooter]

Luckily I had borrowed a double bevel 12" dewalt from a buddy when I was installin the crown in the house. Needless to say Im not fooling with that **** ever again I think a good single bevel will suffice for me. That and a good table saw and I should be good for a while. Unfortunalty I have to hang some dry wall before Im even ready to use the saws

 

[Dr.JohnnyFever]

My sympathies. Drywall is a sadistic invention.

(But I haven't had much luck convincing the wife that OSB with the slick side up is just fine... )

 

[crowldawg]

I agree with JayL . Some of my makitas are pushing 25 yrs old .BTW I would get a miter saw whether you are getting a table saw or not ,Some of those slicing mitre saws have stops that enable you to use the saw like a radial arm .
I only use my table saw to rip wood

 

[trackwelder]

I have the dewalt 12" slider. Its been used on three house builds, two garages, and more decks than I can remember and still going strong. The diablo blade from home depot kicks *** also.