Snap-On 3/4'' Torqometer 600ft/lbs

[2dieseljohn]

I have had this for years, model # is TEX602tfu. It came from from a distant relative who worked as a civilian machinist for the Navy. He bought many a tool surplus. Why he had this I don't know as he only worked on Packards at home. There are letters and # marks on side and cover plate. I asked for a trade in on some stuff from my local Snap-On guy and he said he did not want to mess with it... He did say I should get $300 for it. As it is marked and missing the handle/Bar I will only ask $200. I may be willing to do a part trade as I will be spending some of the $$ rounding out my collection.

 

[jerryW]

What are you looking for?


jerry

 

[2dieseljohn]

I would like to get at least some cash, that said what I'm looking for is any, all or part- a Snap-on 4way angle head in 13mm,19mm. or a long SO 13mm,17mm, a metric set of Flare nut wrenches, a good used set of truck brand metric wrenches(for car kit), might take the right ratchet(s). May be interested in some of the new SO pliers or some of the knipex every one seems to like. What have you got ?? Never know till you ask.
Regards John

 

[2dieseljohn]

New lower price!! $175 shipped to your door in the lower 48. Or trade- Make me an offer I need the room in my box. Thanks

 

[2dieseljohn]

OK- How about $120?? Or trade.
thanks

 

[OldToolMan]

WHAT BAR IS MISSING? lARRY

 

[jerryW]

Drive is in and out, usually do have a round hole in the top drive for a cross bar. Similar to a sliding T handle. Can be used on ratchet or breaker bar.

I've got a 1/2 inch drive, 250# model.


jerry

 

[2dieseljohn]

I believe the bar was 31" long the part # 85TQP. Shows not in stock. This thing is pretty stout and would ?could take a pretty long cheater bar. Do you need more picture? If so I can post some later.
Thanks for your interest.

 

[2dieseljohn]

I just checked and the Hole is 11/16".
Regards

 

[OldToolMan]

john i would be interested i believe the out drive is 3/4 in is ? check my web see what you would like and we will see what we can do.if you find anything note the OTM #'s Larry My direct email [email protected]

 

[2dieseljohn]

Larry- The in and out drive is 3/4". I did spend some time on your site and WOW. I believe we can come to some sort of trade. I am off tomorrow so I'll get a wish list together then. Regards, John

 

[OldToolMan]

John i will be around.let me know when you will be back so i can be on line

 

[2dieseljohn]

Larry- I must say you have set up a very nice site, full of things I did not know I needed. I can tell you have put a lot of thought into you "store". I hope the other members find you-But not before our deal is done.This type of trade is exactly what I had in mind when I put the Torqometer up.

After much debate I have come up with a list:

OTM0273 SO blue screwdriver $9

OTM0448 SO Knipex $35

OTM0404 Craftsmen Pro metric wrenches $50

OTM0416 SO 24' extension $24

Total = $118

I was thinking we could each ship conf.# and Inc. so shipping would be on me for your wrench (apx 4lbs shipping wt). Deal? Let me know. I will try to be online at 2pm pst. Thanks, John Magruder

 

[OldToolMan]

john,give me a call on my cell 530 401-3369 virizon

 

[2dieseljohn]

Larry-Torqumeter mailed this A.M.. I E-mailed you all the info. Again thanks
Regard John