Stuff for trade

[peter_x]

Hi guys.

I am looking for: Any Mac metric wrenches (current series).
Any MAC red hard handles.
Gearwrench 85010 and 85012 (10 and 12mm XL ratcheting)
10mm and 19mm Craftsman raised panel 6-point wrenches.
Snap-on 4" 3/8 drive extension, FXK4
Snap-on 1/4 drive extensions, wobble plus: TMXWP1 (1 inch) TMXWP4 (4 inch), TMXWP8(8 inch)
Snap-on 1/4 drive extensions, regular: TMXK4 (4 inch) and TMXK60 (6inch)
Snap-on Tamper torx sockets except for 30 and 25.
Craftsman 1/2" drive 18mm impact deep

Might be interested in anything. Need impacts and impact swivels in all drive sizes, even 1/4", except for 1/2" drive deep. Matco pinless preferred.
Also diagnostic equipment like AC gauges, fuel pressure testers, alignment tools etc. Gasket scrapers, 2/3 jaw gear pullers. Cutoff wheel, 3/8" grinder.



Updated to remove sold items.

My stuff:

#3: Challenger 7/8 No. 6128
#4: S-K 11/16, engraved
#5 Hi-Test 5/8
#6 Dayton 5/8
#7 Dayton 9/16

#8: 13/16 Craftsman
#9: 3/4 Craftsman
#10-11: 5/8 Craftsman =V=
#12: 5/8 Craftsman (new series)

#17-22: No-name 1/2 drive impact swivels, 1/2 - 7/8 missing 11/16.

More stuff to be posted later...

 

[ryannotbryan]

PM sent.......

 

[peter_x]

Craftsman sockets, all never used:

On the right, metric,

1/4 drive: deep 9mm

3/8 drive: short 14 and 15,

1/2 drive: short 18 and 19

On the left, standard,

deep 1/4 drive: 9/32, 5/16, 7/16,

short 3/8 drive (these are the only 12-point): 7/16, 1/2 (both dual marked and not) , 9/16, 5/8

deep 3/8 drive: 7/16, 1/2, 9/16.

 

[peter_x]

Gearwrench s-wrench, 13-14mm, 15-17mm, new

Cornwell extension, about 3 inches, 3/8 drive, pinned
Apex extension, about 4 inches, 3/8 to 1/4 reducing, pinned

Craftsman 8-point sockets, 7/16 and 3/8

 

[kblazer87]

I have 6 Snap on 1/4" drive extensions for sale.

3 are wobbles:
TMXW100-10"
TMXW4 - 4"
TMXW2 - 2"

2 are knurled:
TMXK60 - 6"
TMXK2 - 2"

1 REGULAR:
TM-60 - 6" - 1963 date code but in excellent shape

Also have a couple of 3/8":
FXW11
FXW3
FX-2
FX1

All are in excellent shape.

 

[peter_x]

1/2" drive sockets:
14mm Great neck, 15, 18, 21, 22 Craftsman

Top right corner: Extra-deep 12-point 12mm Snap-on impact, 1/2" drive. Box said it was for the cam bearing caps on Detroit deisels, I used it to remove Crown Vic driveshafts. Now I have the special tool.

Extensions:
3/8" drive Craftsman 10", impact use GONE
1/4" drive Craftsman, 3" air ratchet use GONE

No-name nutdriver, 3/8"

Mac PH3 screwdriver, soft grip

Snap-on 1/2" drive swivel impacts, 14, 15, 18, 24. (The 15mm has a slightly newer graphic (2009), the rest are 2008 or 2007). GONE

 

[kblazer87]

Are you not interested in any of the extensions I listed?

 

[peter_x]

PM inbound...

 

[peter_x]

Snap-on tray for 4-piece pry bar set
VACO USA 1/8" hex t-handle
Craftsman torx screwdrivers, T10, 15, 20, 25, 27GONE
craftsman 7/8 wrench GONE
Sears Japan BF 1/2 wrench
Frank and Warren double open end wrench, Japan, 3/4 - 7/8
Frank and Warren double open end wrench, Japan, 1/2 - 9/16

 

[OldToolMan]

i have some of the tools also an extension no longer available from S-O,a 14"wobble 1/4" drive no markings looks new.check out my web site

 

[peter_x]

Bottom pipe wrench: Walworth Stillson 24" USA. I've never seen a pipe wrench like this, it has leaf springs on the back and front of the head to keep it tight on whatever you are turning (presumably).

Top pipe wrench: Dura-life Heavy Duty, no COO. Also 24". Quite he opposite of the Stillson, it has a lot of play in the head, and it seems the adjusting wheel has been taken from another pipe wrench. The threads don't seem to match up exactly because you have to hold the head while adjusting it or it jams.

The C-clamp is an Armstrong 78-406 USA, 7".

Pipe wrenches will probably be expensive to ship, so I am thinking local pickup. I could see if they will fit in a flat rate box for whomever is interested.

Tenma 72-860A sound level meter. Comes with case, windscreen, CD-ROM, and RS-232 cable. You can hook it up to a PC for datalogging and graphing. Uses 9V battery.

 

[peter_x]

Snap-on A/C hub pullers, ACT5 (left) and ACT 2 with ACT3 screw (right).

Snap-on puller CJ98 with CJ83-3 center screw and CJ66-15-3 centering adapter.