To avoid these ads, REGISTER NOW!

The making of a table

To avoid these ads, REGISTER NOW!

LXCam

ALLIANCE MEMBER
Joined
Apr 23, 2013
Messages
19,153
Location
AZ
Ooohhhh. A big boy heated pressure washer. How big?

I’ve got a Landa, luv that thing.
 
OP
R

RivennHewn

Well-known member
Joined
Jun 4, 2011
Messages
10,374
Location
PNW
Ooohhhh. A big boy heated pressure washer. How big?

I’ve got a Landa, luv that thing.
Too big for me to get off the pallet by myself.

Had to use the forklift and pallet jack to get it placed.

Didn’t bother reading the specs, but I did call my electrician, gas piper, and ductwork subs.
 
OP
R

RivennHewn

Well-known member
Joined
Jun 4, 2011
Messages
10,374
Location
PNW
The equipment is going into a heavy machinery repair shop.

The heated pressure washer is for cleaning the machinery prior to bringing it in the shop.

The grated section in the wash down area is for sludge settlement.

Water then flows to a two compartment tank for more settlement, then pumped into the gas fired evaporator.

No dirty water leaves the site. No oily water flows into the storm/sewer or ends up in the river.

Yes, tanks will have to be vac trucked clean and disposed of properly.

I think we’ll be seeing more of this kind of systems required by building codes.

It’ll be interesting to see what the monthly operating cost are. It was a significant cost to install.
 

Attachments

  • IMG_0468.jpeg
    IMG_0468.jpeg
    887.8 KB · Views: 49
  • IMG_0474.jpeg
    IMG_0474.jpeg
    884.4 KB · Views: 38
  • IMG_0486.jpeg
    IMG_0486.jpeg
    671.8 KB · Views: 65

LopezBart

Well-known member
Joined
Oct 13, 2023
Messages
2,547
Location
Lopez Island, WA
I’ve done a few OWS systems and the operational cost is cheaper than the fines.
Which of course is exactly the point of the fines; behavior modification. One of the things we (humans) are figuring out is that there's no "away"; we have to think about the long term consequences of what we're doing even though it may be awkward or contrary to previous practice.

We used to dispose of waste engine oil by pouring it along the fence lines to kill weeds as kids. I wondered about it then, but in the early 70s there weren't a lot of options.

We now live on a small island; there used to be a local dump, but everything is trucked off island now. A trashcan is $10 at the transfer station, but recycling (sorted and cleaned) is free. Almost everyone recycles.

Collectively of course, everyone lives on a small island.
 
OP
R

RivennHewn

Well-known member
Joined
Jun 4, 2011
Messages
10,374
Location
PNW
Which of course is exactly the point of the fines; behavior modification. One of the things we (humans) are figuring out is that there's no "away"; we have to think about the long term consequences of what we're doing even though it may be awkward or contrary to previous practice.

We used to dispose of waste engine oil by pouring it along the fence lines to kill weeds as kids. I wondered about it then, but in the early 70s there weren't a lot of options.

We now live on a small island; there used to be a local dump, but everything is trucked off island now. A trashcan is $10 at the transfer station, but recycling (sorted and cleaned) is free. Almost everyone recycles.

Collectively of course, everyone lives on a small island.
“Don’t **** where you sleep “
 
OP
R

RivennHewn

Well-known member
Joined
Jun 4, 2011
Messages
10,374
Location
PNW
Started a fun little project.

Turning an old Perfect Handle screwdriver into an oyster knife.

Cut up a little burl for the scales, then started on the blade.

Into the normalizing/quinching/tempering process after some stock removal and a little ring’n on the anvil.
 

Attachments

  • IMG_1102.jpeg
    IMG_1102.jpeg
    921.3 KB · Views: 45
  • IMG_1107.jpeg
    IMG_1107.jpeg
    1.8 MB · Views: 41
  • IMG_1108.jpeg
    IMG_1108.jpeg
    1 MB · Views: 37
  • IMG_1110.jpeg
    IMG_1110.jpeg
    590.5 KB · Views: 39
  • IMG_1113.jpeg
    IMG_1113.jpeg
    527.3 KB · Views: 41
To avoid these ads, REGISTER NOW!

WoodsTruck

Well-known member
Joined
Jan 12, 2013
Messages
1,024
Started a fun little project.

Turning an old Perfect Handle screwdriver into an oyster knife.

Cut up a little burl for the scales, then started on the blade.

Into the normalizing/quinching/tempering process after some stock removal and a little ring’n on the anvil.
I think this requires a tutorial video on how it works. You didn't even show pictures on how you charge it.
 
OP
R

RivennHewn

Well-known member
Joined
Jun 4, 2011
Messages
10,374
Location
PNW
I think this requires a tutorial video on how it works. You didn't even show pictures on how you charge it.
I’d have to hire a videographer, both hands busy today😜

I’ve never rehandled one of these. Kind of a pain. Both ends have funky shapes. Lots of filing😕
 

Attachments

  • IMG_1116.jpeg
    IMG_1116.jpeg
    562.6 KB · Views: 34
  • IMG_1115.jpeg
    IMG_1115.jpeg
    586.9 KB · Views: 41
OP
R

RivennHewn

Well-known member
Joined
Jun 4, 2011
Messages
10,374
Location
PNW
Yay!

Finished the quenching/tempering process.

A file no longer cuts the blade. Time to break out the Tormek, and finish on the wet stone
 

Attachments

  • 94E9770C-0F09-43D2-8F36-A55084FB52E9.jpeg
    94E9770C-0F09-43D2-8F36-A55084FB52E9.jpeg
    848.9 KB · Views: 37
OP
R

RivennHewn

Well-known member
Joined
Jun 4, 2011
Messages
10,374
Location
PNW
Made some progress on the knife!

Got close to final shape, and started honing.

Pretty happy with the results.

Then I used a dab of epoxy to temporarily attach the scales. This allowed me to drill the pin holes, and work on the shape. I’ll soak the scales in penetrating epoxy prior to mounting them. This will plasticize them. Good for wet environment.
 

Attachments

  • IMG_1151.jpeg
    IMG_1151.jpeg
    823.1 KB · Views: 31
  • IMG_1152.jpeg
    IMG_1152.jpeg
    750.5 KB · Views: 29
  • IMG_1153.jpeg
    IMG_1153.jpeg
    517 KB · Views: 29
  • IMG_1154.jpeg
    IMG_1154.jpeg
    663.8 KB · Views: 29

Bears Fan

Well-known member
Joined
Jan 26, 2012
Messages
3,439
Location
Indiana
img_1170-jpeg.2144764


The wooden handle is gorgeous :cool:
 
OP
R

RivennHewn

Well-known member
Joined
Jun 4, 2011
Messages
10,374
Location
PNW
I made a table.


It’s for the new job site trailer.

My PM wanted me to obtain a conference table but when I asked what was in the budget, he said “Zero”.

Pulled some old concrete forms out of the dumpster, and threw some old slabs on it.

Maybe next time he’ll plan better
 

Attachments

  • IMG_4484.jpeg
    IMG_4484.jpeg
    1.4 MB · Views: 27
  • IMG_4486.jpeg
    IMG_4486.jpeg
    1 MB · Views: 27
  • IMG_4487.jpeg
    IMG_4487.jpeg
    1.2 MB · Views: 31
  • IMG_4495.jpeg
    IMG_4495.jpeg
    1.3 MB · Views: 32
  • IMG_4496.jpeg
    IMG_4496.jpeg
    1.6 MB · Views: 36

DGZRT

Well-known member
Joined
Apr 7, 2019
Messages
94
Location
Wisconsin, Stevens Point
This was my table project last year.
Turned out pretty good . I made it for my Daughters new house .
 

Attachments

  • IMG_5528.jpeg
    IMG_5528.jpeg
    986.9 KB · Views: 33
  • IMG_5532.jpeg
    IMG_5532.jpeg
    799.3 KB · Views: 31
  • IMG_5650.jpeg
    IMG_5650.jpeg
    965.3 KB · Views: 29
  • IMG_6258.jpeg
    IMG_6258.jpeg
    911.6 KB · Views: 29
  • IMG_6266.jpeg
    IMG_6266.jpeg
    1,018.8 KB · Views: 32
  • IMG_6271.jpeg
    IMG_6271.jpeg
    910.7 KB · Views: 30
  • IMG_6267.jpeg
    IMG_6267.jpeg
    873.8 KB · Views: 31
To avoid these ads, REGISTER NOW!
Top Bottom