The Milwaukee addiction thread! :)

[Ign]

Just Remember Amazon is not considered an authorized Milwaukee reseller.
I do not know if that effects warranty or not don't know if it would stop me from buying there

Worst case you'll have 5 years from date of manufacture built into the serial #. So in most cases it doesn't matter much. I also do not know for certain if Milwaukee would refuse to extend to 5 years from date of purchase if you provided an Amazon invoice.

 

[tj00xj91]

Last one

 

[Bighead38]

I believe that size difference has me sold on the new impact.

 

[bsechris]

I believe that size difference has me sold on the new impact.

Same here: I'm glad I have been too broke to afford the high torque. I was wanting to make sure it could take off lug nut off my truck, and my families 3/4-1 ton pick up's. I didnt trust the compact ones to take them off even though they were spec'ed to. I was afraid dirt, tire places over torquing, and time would cause the nut busting power to exceed what the compacts could handle.

With the mid torque, I have no questions it will do that and much more for my needs. Cant wait to get my hands on one.

 

[icu2tsx]

Speaking of new compacts. Milwaukee rep demo the m18 hex Impact surge. And I got to play with it. Man it's way quieter, smaller, a little wider compared to M12 fuel hex Impact. M12 fuel hex Impact going on up on offerup/Craigslist now lol getting the surge for sure as soon as this puppy sells.

 

[DerekV]

Last one

Bingo [emoji108]thanks for these!

Sold!

 

[Frontierajl]

I think I'm gonna sell or trade my 2763 for the mid size. It looks a lot more practical for me, size wise. I think it would get used more around here.


Sent from my iPhone using Tapatalk

 

[kctyphoon]

Dunno if this is news or not - new m18 1/4" die grinder

https://www.milwaukeetool.com/power-tools/cordless/2784-20

 

[kctyphoon]

Dunno if this is news or not - new m18 1/4" die grinder

https://www.milwaukeetool.com/power-tools/cordless/2784-20

 

[Locker537]

I'm going to be renovating two bathrooms and our foyer in the coming months and suspect it makes the most sense to invest in the right tool to make tile/thinset removal easier.

I'm already invested in both M12 and M18; can anyone recommend the right rotary hammer for this type of job?

I'm not opposed to a corded version if the cost savings are there.

 

[anndel]

I'm going to be renovating two bathrooms and our foyer in the coming months and suspect it makes the most sense to invest in the right tool to make tile/thinset removal easier.

I'm already invested in both M12 and M18; can anyone recommend the right rotary hammer for this type of job?

I'm not opposed to a corded version if the cost savings are there.

Bosch Bulldog

 

[Locker537]

Bosch Bulldog

I like the sound if that. It's more affordable as well.

 

[DFB]

So I first heard about these just yesterday

Cool...Milwaukee new line of hammers. I've wanted to try Stiletto for a while so maybe its time for one of these. I have had my steel Estwings for decades now, along with a 20oz Craftsman rip that was my very first hammer for work like 35 years ago.

Pricing seems reasonable and market competitive.

I wonder if HD will stock them? :

http://www.coptool.com/milwaukee-tool-framing-hammers-spring-2017/

 

[kctyphoon]

I was seriously just wondering today when Milwaukee was going to FINALLY make a hammer... now they just need some cool safety sun glasses.. it's about friggin time..

 

[kctyphoon]

Bosch Bulldog

Ditto

 

[Roobaix]

I'm going to be renovating two bathrooms and our foyer in the coming months and suspect it makes the most sense to invest in the right tool to make tile/thinset removal easier.

I'm already invested in both M12 and M18; can anyone recommend the right rotary hammer for this type of job?

I'm not opposed to a corded version if the cost savings are there.

The M18 Fuel would be a nice choice.
The M12 Fuel doesn't have a hammer only option unfortunately.

 

[DFB]

The big impact single battery kit 2763-21XC on special today @HomeDepot

http://www.homedepot.com/SpecialBuy...223_sbotd_3008362-_-sbotd_cta&et_rid=74767809

 

[Fixed]

I'm not opposed to a corded version if the cost savings are there.

Go corded. Constant chipping will eat even large batteries for breakfast.



Sent from my Nexus 5 using Tapatalk

 

[FigureItOut]

Speaking of rotary hammers, I've been waiting to see a deal on the 2715 1-1/8" SDS, but I spotted the 2712 1" SDS at HD for $150 and couldn't pass it up.

On another note, I need some opinions. I've been doing a bunch of trailer hitch installs and it looks like spring may bring quite a few more. I'm thinking of getting a cordless ratchet or right angle impact to easily snug up a hitch while I'm holding it. The dilemma is that I'm not super interested in getting into M12, I'm very happy with Bosch there, but the M18 right angle impact looks ridiculously clunky. So what are people's favorites Milwaukee ratchets or right angle impacts and what might you suggest for hitch installs and general work?

 

[dacan23]

Visited a Milwaukee service center today to drop off a faulty heated jacket. Ultimate candy store, they have every little thing possible, but at full retail prices.... A SDS bit set sold at HD for $25 and other places for $22, was $33 there.... Cool to see everything the pretty much make, though no Mid Torque was on display, they had new boxed ones though.

 

[dacan23]

My extra string line spools and spare head finally shipped from Acme today.

 

[FigureItOut]

My extra string line spools and spare head finally shipped from Acme today.

Got my string yesterday, a month or so after the trimmer.

 

[DerekV]

Visited a Milwaukee service center today to drop off a faulty heated jacket. Ultimate candy store, they have every little thing possible, but at full retail prices.... A SDS bit set sold at HD for $25 and other places for $22, was $33 there.... Cool to see everything the pretty much make, though no Mid Torque was on display, they had new boxed ones though.

Which one did you go to? I've been to the one in Westwood (MA) and it's pretty cool. Funny because the Dewalt service center is right next door, same building and everything.

 

[DerekV]

On another note, I need some opinions. I've been doing a bunch of trailer hitch installs and it looks like spring may bring quite a few more. I'm thinking of getting a cordless ratchet or right angle impact to easily snug up a hitch while I'm holding it. The dilemma is that I'm not super interested in getting into M12, I'm very happy with Bosch there, but the M18 right angle impact looks ridiculously clunky. So what are people's favorites Milwaukee ratchets or right angle impacts and what might you suggest for hitch installs and general work?

I was in the same boat a while back - didn't wanna buy new batteries, but didn't wanna get the wrong tool. I sprung for the M18 RA impact driver and I don't regret it. It's an awesome tool. It's plenty powerful enough to run down and snug bolts/nuts with one hand. You can always go back with a different tool/two hands afterwards. I keep the head spun 180* from "stock" and that keeps the battery 100% outta the way. It might not have the power to break a ton of bigger stuff free, but it can certainly run em down quickly, and it's reactionless.

Now as far as driver vs. wrench - up to you. Do you have or are willing to get 3/8" impact sockets? Do you only plan on using it for this task (that is, no drilling or screw driving)? If yes to both of those, perhaps the impact wrench is the way to go. The driver is more versatile. I only have 1/2" impact sockets and don't ever plan to get 3/8" impacts. I also wanted to be able to easily drill holes or drive screws in TIGHT quarters - the impact driver just made more sense to me.

Remember, it's not gonna break loose rusted fasteners that were torqued to 75+ ft/lbs 8 years ago. If you go into it knowing that, you'll be satisfied.

PS: this rig took my down pipe off of my turbo (aka 4 OLD/crusty/rusty/heat-cycled 16mm nuts)

 

[DFB]

My extra string line spools and spare head finally shipped from Acme today.

Got my string yesterday, a month or so after the trimmer.

What this in the OM...use ONLY Milwaukee string?

And why did you buy xtra parts already?

 

[chrisexv6]

What this in the OM...use ONLY Milwaukee string?

And why did you buy xtra parts already?

Always nice to have a spare head or two already filled with line and ready to go.

Murphys law says you will run out when farthest away from your spare line and by the time you get to it you'll be all sorts of fired up and not in the frame of mind to reload correctly

 

[DFB]

On another note, I need some opinions. I've been doing a bunch of trailer hitch installs and it looks like spring may bring quite a few more. I'm thinking of getting a cordless ratchet or right angle impact to easily snug up a hitch while I'm holding it. The dilemma is that I'm not super interested in getting into M12, I'm very happy with Bosch there, but the M18 right angle impact looks ridiculously clunky. So what are people's favorites Milwaukee ratchets or right angle impacts and what might you suggest for hitch installs and general work?

Well I have both the M12 ratchet and the RA impact driver I really like the reactionless feature on the impact. I snugged up almost 100 9/16" bolt and nut combos pretty to close to its max torque rating when changing out rototiller tines on our 60 inch PTO run tiller at work. It made fast work of it and saved me a lot time when I went to do final torque around 80 ftlbs.

Only drawback it is what is and you have to change out tools to get it any tighter As for loosening they are limited in breakaway torque.

Best I get out of ratchet just running down bolts is maybe 25ftlbs and I don't rally know how much arm torque one can really apply with it. I've probably done 40 ftlbs maybe? without feeling like I would maybe break something. Plus there is a slight abrupt stop with the ratchet running down fasteners unless you feather it.

I think the M18 RA impact would be good choice if your not that interested in M12 series of tools. It worth having one for assembly work.

 

[Ign]

The best thing for me for hitches and even spring work has been the Astro Nano 1/2" impact.

 

[Locker537]

Speaking of rotary hammers, I've been waiting to see a deal on the 2715 1-1/8" SDS, but I spotted the 2712 1" SDS at HD for $150 and couldn't pass it up.

On another note, I need some opinions. I've been doing a bunch of trailer hitch installs and it looks like spring may bring quite a few more. I'm thinking of getting a cordless ratchet or right angle impact to easily snug up a hitch while I'm holding it. The dilemma is that I'm not super interested in getting into M12, I'm very happy with Bosch there, but the M18 right angle impact looks ridiculously clunky. So what are people's favorites Milwaukee ratchets or right angle impacts and what might you suggest for hitch installs and general work?

I haven't installed a hitch, but I will say to keep in mind the differences between the cordless ratchet and impact. The cordless ratchet is meant to speed up turning fasteners, not break them loose or torque them past ~30 ftlbs.

 

[FigureItOut]

I haven't installed a hitch, but I will say to keep in mind the differences between the cordless ratchet and impact. The cordless ratchet is meant to speed up turning fasteners, not break them loose or torque them past ~30 ftlbs.

Yeah I know, I'd always be coming back with a torque wrench. I'm looking to quickly snug things down, holding up a hitch and swinging a ratchet in tight quarters is a bit tough.

 

[Locker537]

Yeah I know, I'd always be coming back with a torque wrench. I'm looking to quickly snug things down, holding up a hitch and swinging a ratchet in tight quarters is a bit tough.

In terms of convenience, the ratchet is amazing. Given what you just said I don't think you will regret it.

 

[Locker537]

I'm going to have to walk through a couple local HD stores and see if I can find that rotary for $150. At that price, it might make more sense then the Bosch Bulldog that's being recommended.

 

[FigureItOut]

I'm going to have to walk through a couple local HD stores and see if I can find that rotary for $150. At that price, it might make more sense then the Bosch Bulldog that's being recommended.

I was eyeing the Bosch too, but yeah at $150 it was a no-brainer. I've been getting by fine with a hammer drill and only occasionally wish I had SDS, so I think I'll be happy.

In terms of convenience, the ratchet is amazing. Given what you just said I don't think you will regret it.

It looks pretty sweet. I wish I could get my hands on the ratchet and the RA impact side by side to compare.

 

[DFB]

Not much difference in size with the M12 stuff

M12 RA Impact driver is a little longer than the ratchet and of course you have to use a socket adapter. The M18 series has a couple additional features like a rotating head and has 2 speeds and the wrench runs about $30 more than the driver. If that M18 RA wrench ever goes on price reduction I would consider getting it.

 

[cool_as_crap]

I’m looking for feedback on the 3/8” impact 2754 if anyone can help.
Does anyone use this for automotive? What have you found that you can’t do with it.
Loosen exhaust? Lugnuts?

Could I use this on, say engine work like removing a flex plate off of a BB chevy or general bolt removal?

I also want the mid torque but I’m debating on buying both, the 3/8 for smaller stuff.

 

[Ign]

The 2754 is good for 85-90% of automotive. It will almost always do lugs for me. If you live in the rust belt YMMV. If a lug is severely rusted, over-torqued or cross threaded it probably won't.

They're surprisingly potent for their size, but they're no 2763/2235timax by any means.

I think the compacts really shine for top side engine work and FEAD stuff (at least on trucks for the latter).

 

[Antwonizzle]

I've had my 2754 for about a week and I am extremely impressed with it. it handles properly torqued lug nuts and brake caliper bracket bolts with ease. its just as, if not more, powerful as my snap on ct8810a. all I can say is this may be the beginning of the end for my snap on cordless collection.

 

[Caparris]

I've had my 2754 for about a week and I am extremely impressed with it. it handles properly torqued lug nuts and brake caliper bracket bolts with ease. its just as, if not more, powerful as my snap on ct8810a. all I can say is this may be the beginning of the end for my snap on cordless collection.

I sold all of mine. They weren't even close (though that has been a year or two so I was giving them the benefit of the doubt..)

 

[DFB]

I'm finding the 3/8" 2754 every bit as powerful as my old 1/2" 2655B and on the average is a good 1/2 inch shorter with comparative socket attachments.

Still not completely sold on that 4th position thing though but it's there

If I remember right Milwaukee rate them for fasteners up to 7/8" Usually there is no problem under 1/2", and testing it on anything I've bench torqued its removed everything.

I have had a few 1/2 ton truck wheel lugs the old B wouldn't loosen and changing out a pintle hitch on our work dump truck it only got two of the four bolts (I think the 2763 snapped them off though or at least one anyway and it struggled with a couple rear bumper bolts on an old truck. But all this stuff has seen serious winter weather too. Did grind away and remove every dirty and damaged 9/16 bolt and nut combo on that rototiller tine R&R mentioned in a prior post except for maybe two? that had severely damaged threads. Easily did all my dual axle trailer wheel lugs.

 

[DFB]

PS: this rig took my down pipe off of my turbo (aka 4 OLD/crusty/rusty/heat-cycled 16mm nuts)

Derek that looks like a protective rubber boot on the tool in your photo...

Is it a Milwaukee part?