- Location
- Lebanon, OH
- Price
- $16,000.00
Tormach Series 3 Mill
Extremely nice and well maintained Tormach PCNC 1100 with tooling. Purchased new 2 years ago and used in my home shop for small design and prototyping. I’ve recently upgraded to a bigger machine and need the floor space. These machines are great entry for home shops, small production runs and prototyping. It has been upgraded with the new Series 3 motors, and pneumatic drawbar. Can be seen under power by appointment
Buyer must pay $500 deposit within 24 hours. Cash, Wire Transfer, or Cashier’s Check accepted. No shipping, local pickup only. I am ~30 miles North of Cincinnati. I have a lift and can help load. Buyer assumes all liability and responsibility for transport. Machine weighs ~1,300 pounds.
Tormach PCNC Series 3* – *Upgraded motors and control board.
Dell Optima with Mach3 control s/w
Deluxe Stand with machine arms, and both the lower and upper tool tray
Pneumatic Drawbar
4th Axis Drive
8” Tilting Rotary Table
8” 3 Jaw Chuck
Tailstock for 8” chuck
Passive workset probe
6-ER-20 Collet Chucks
2- ER-20 Collet Chuck Nuts
4-1/2 Inch TTS Set Screw End Mill Tool Holders
4-3/8 Inch TTS Set Screw End Mill Tool Holders
1-JT1 TTS Arbor with 0-1/4" Drill Chuck
2-1/4 Inch TTS Set Screw End Mill Tool Holders
1-5/16 Inch TTS Set Screw End Mill Tool Holder
2- JT6 Arbors
2- JT1 Arbor with 1/64-1/4 Drill Chuck
1-Diamond Drag Engrave with 90 degree tool
2- TTS 1/2 Inch Shell Mill Arbors
1- Tormach 5" Vise
1- Tension Compression Tapping Set
1- TTS Boring Bar Head
Extremely nice and well maintained Tormach PCNC 1100 with tooling. Purchased new 2 years ago and used in my home shop for small design and prototyping. I’ve recently upgraded to a bigger machine and need the floor space. These machines are great entry for home shops, small production runs and prototyping. It has been upgraded with the new Series 3 motors, and pneumatic drawbar. Can be seen under power by appointment
Buyer must pay $500 deposit within 24 hours. Cash, Wire Transfer, or Cashier’s Check accepted. No shipping, local pickup only. I am ~30 miles North of Cincinnati. I have a lift and can help load. Buyer assumes all liability and responsibility for transport. Machine weighs ~1,300 pounds.
Tormach PCNC Series 3* – *Upgraded motors and control board.
Dell Optima with Mach3 control s/w
Deluxe Stand with machine arms, and both the lower and upper tool tray
Pneumatic Drawbar
4th Axis Drive
8” Tilting Rotary Table
8” 3 Jaw Chuck
Tailstock for 8” chuck
Passive workset probe
6-ER-20 Collet Chucks
2- ER-20 Collet Chuck Nuts
4-1/2 Inch TTS Set Screw End Mill Tool Holders
4-3/8 Inch TTS Set Screw End Mill Tool Holders
1-JT1 TTS Arbor with 0-1/4" Drill Chuck
2-1/4 Inch TTS Set Screw End Mill Tool Holders
1-5/16 Inch TTS Set Screw End Mill Tool Holder
2- JT6 Arbors
2- JT1 Arbor with 1/64-1/4 Drill Chuck
1-Diamond Drag Engrave with 90 degree tool
2- TTS 1/2 Inch Shell Mill Arbors
1- Tormach 5" Vise
1- Tension Compression Tapping Set
1- TTS Boring Bar Head