Williams Large Ratcheting Wrench Sets?

[sightbike]

Have the Taiwan made Williams ratcheting wrench sets in both SAE and metric. Looking to buy the 4 larger wrench set add-on; however, wondering if the 13/16 - 1” and 21-25mm are the exact same set with different markings. For reference, the SAE set is JHWWS-1164RC and metric set is JHWMWS-4RC.

Curious if anyone has both sets and confirm whether sizes are actually measure different.

​

 

[nicks78camaro]

I don't have them but I bet they are.

 

[sightbike]

Anybody? Someone’s got to have the sets given this bunch!

 

[JerseyBoatBuilder]

The lengths, thickness and other sizes are listed for each wrench if you go to the set pages and select each individual wrench

 

[WWheeler]

I don't, but I will before long. This post just got me to order the metric set (JHWMWS-4RC). "Arriving July 15-17". I didn't even know that was a thing. I've got a 12pc SuperCombo reversible ratcheting set from 8mm-19mm that's just begging for these bigger siblings.

I'm definitely going to have to rearrange my wrench drawers now though. lol

 

[sightbike]

The lengths, thickness and other sizes are listed for each wrench if you go to the set pages and select each individual wrench

Referring to the open and box ends of the wrench. I’ve seen the measurements on the technical pages and are marginally different so much so that it makes me question that different tooling was developed for the sets. Hence the question are they the same with different markings.

 

[KnurledNut]

I have some singles. If I get time I can see how the tolerances measure for their given size.

 

[NUTTSGT]

This is about all that I can do, if these are the correct wrenches.

 

[sightbike]

@NUTTSGT - thanks. Have you used the 13/16 on a 21mm and the 15/16 on 24mm? If so, how was the fit?

 

[KnurledNut]

This is about all that I can do, if these are the correct wrenches.

Can you throw a caliper on the 7/8?
My 22mm is showing:
Open end .8755
Box end hex corner to corner 1.06
OAL is 288mm

@sightbike
I would honestly be surprised if they are using the same wrench for both sizes. They really aren't equivalents. Close enough only counts in horseshoes and hand grenades.

 

[NUTTSGT]

Sorry guys, not today, getting ready for work. I can Saturday if I remember.

 

[KnurledNut]

My 24mm is showing:
Open end .950
Box end hex corner to corner 1.99

 

[sightbike]

@KnurledNut - thanks for measurements!

@NUTTSGT - appreciate if you could post measurements on your 7/8 and 15/16 to compare. Thanks!

 

[NUTTSGT]

@KnurledNut - thanks for measurements!

@NUTTSGT - appreciate if you could post measurements on your 7/8 and 15/16 to compare. Thanks!

Yeah I can tomorrow... wasn't expecting to be working a double shift today.

 

[NUTTSGT]

Here's what I found. It did seem like measuring on the box end did vary slightly front to back.

 

[KnurledNut]

Cliff notes:

Size​	Metric Conversion​	Decimal Conversion​	Measured Open End​	Measured Box End​
22mm​	-​	.8661​	.8755​	1.06​
7/8"​	22.23mm​	.875​	.887​	1.15​
------------------------------------​	------------------------------------​	------------------------------------​	------------------------------------​	------------------------------------​
24mm​	-​	.9449​	.950​	1.99​
15/16"​	23.81mm​	.9375​	.940​	1.91​

 

[sightbike]

@KnurledNut @NUTTSGT - thank you both! Really appreciate you gentlemen taking the time to provide measurements.