Tekton Angle wrench set

[DieselSaves]

I have a handful of Home Depot gift cards to blow and since Milwaukee is being stingy about sales on what I want to buy, I’m looking at the Tekton metric angle wrench set, 10mm-27mm. I remember when they were introduced to the market and I liked the 30/60 angle like Snappy and the US made part is nice, but does their manufacturing process on these wrenches make for a durable wrench? I’ll probably buy them and learn the hard way but until then, has anyone here owned and used a set?

 

[DekNgo]

I have a few individual wrenches and like them for what they are. They apparently aren't as strong as forged wrenches (see the video below), but I'm not using mine for high-torque scenarios.

 

[DieselSaves]

Thanks for the video. I had suspicions that the machined wrenches were a bit weaker. I seldom run into a hydraulic fitting that is completely seized, so this might not be a problem. Couple that with these bring so much cheaper than my SO ones and I never run across used metric wrenches so maybe it’s worth the gamble.

 

[BarrelRoll]

I have a set of Williams 15/60 angle i think the fit and finish is terrible on so I bought 1 tekton. I think they look really uncomfortable though it's growing on me. After a couple

When using angle wrenches on hydraulics I find if they won't break free by hand usually 1 wack with a dead blow and it's loose. I'm not too worried about destroying them, if I do their warranty is easy.

For the money they are much nicer wrench than the made in USA Williams.

 

[cavalry]

I have the Tektons, full sets SAE and Metric.
They have their purpose, which is low to medium torque with poor access. They are phenomenal for hydraulic work. Wrench quality overall is pretty good. I had a couple with really shallow engraving which I was not happy with but mine was when they first came out after months of being on a waiting list, so hopefully they got their QC fixed.
I recently upgraded my SAE to Snapon, but I will keep the Metric Tekton for the forseable future.

 

[cavalry]

I had a couple with really shallow engraving which I was not happy with

 

[dnschmidt]

Horses for courses. These wrenches aren't long enough to make the strength difference matter much and their intended usage "Hydraulic Fittings" makes ultimate strength a secondary consideration. To me they seem adequate for the job they are intended to perform.

 

[2ndGearRubber]

I have tekton and snap on 30/60 angle wrenches. Both have their pluses and minuses, but I have no fear about cranking on the tektons. They're not long wrenches to begin with, so their toughness isn't required to be as high as say a double offset long box end wrench.

 

[LWB]

I have tekton and snap on 30/60 angle wrenches. Both have their pluses and minuses, but I have no fear about cranking on the tektons. They're not long wrenches to begin with, so their toughness isn't required to be as high as say a double offset long box end wrench.

Could you expand on that? Curious what your thoughts are on each.

 

[82355]

Horses for courses. These wrenches aren't long enough to make the strength difference matter much and their intended usage "Hydraulic Fittings" makes ultimate strength a secondary consideration. To me they seem adequate for the job they are intended to perform.

I have double wrenched my Snap On angle wrenches many times. I'd be curious if the Tektons could take that.

I'd rather have a low quality 30/60, over a high quality 15/60. I have no idea why anyone still makes a 15/60???

Martin

 

[charbar]

What about the Capri angle wrenches? I didn't know they made them till a few weeks ago. I don't own a single Capri tool so I couldn't say what quality would be like but they could be another option at least.

Anybody here have any experience with them?

 

[DieselSaves]

What about the Capri angle wrenches? I didn't know they made them till a few weeks ago. I don't own a single Capri tool so I couldn't say what quality would be like but they could be another option at least.

Anybody here have any experience with them?

I own and like the Capri 3/8 flex head ratchet. I’d look at their combination wrenches if I needed a set. The angle wrenches I’ve seen from them are 15/60 and that’s a non starter for me.

 

[charbar]

I own and like the Capri 3/8 flex head ratchet. I’d look at their combination wrenches if I needed a set. The angle wrenches I’ve seen from them are 15/60 and that’s a non starter for me.

They must have updated to a new style like Tekton did then. The sets on the Capri website are a 60/30 and have an 'anti slip groove' style open end. Kinda reminds me of my Proto ASD wrenches.

https://www.amazon.com/dp/B09LJGLKCL/?tag=atomicindus08-20

 

[charbar]

Here's the Home Depot link, I forgot you said you had gift cards for there.

Capri Tools Metric 30° and 60° Angle Open End Wrench Set (19-Piece) CP11900-19MT - The Home Depot

The Capri Tools 30° and 60° Angle Open End Wrenches let you access hard-to-reach areas where clearance is limited. 30° and 60° angle open ends with the same size opening on both ends, these wrenches give

www.homedepot.com

It is a 6-24 mm set instead of the Tektons 10-27mm though. I'm not sure what line of work you are in but for me (auto mechanic) the smaller ones in the Capri set would be used a million times more than the bigger ones in the Tekton set.

I was going to get the Tektons but I'm almost talking myself into getting the Capris instead . The metric set anyway....SAE I will need to go Tekton to get the bigger sizes for hydraulic lines on tractors/equipment.

 

[infinite97]

I have the SAE set up to 1 1/4”. I like it, I don’t love it. The corners of the wrenches are not well rounded, which makes it quite painful to apply force. There are no real raised panels on the sides of the wrenches, which means if I Am slick with oil and set the wrench on a flat surface, it’s quite hard to pick up.

No concerns about quality or strength, I hit them with hammers, use my wrench extenders, etc.

 

[2ndGearRubber]

Could you expand on that? Curious what your thoughts are on each.

The way the jaws protrude from the beam are at slightly different angles. I've had both in my hand and wished I owned the other due to access issues with the beam. They have a little video about how their wrench reaches something a snap on can't. Well I've been in that situation, and the reverse where I wished my tektons were snap ons.

Thicker beam on the tekton also makes them a little less dainty for flipping in tight areas.

 

[LWB]

The way the jaws protrude from the beam are at slightly different angles. I've had both in my hand and wished I owned the other due to access issues with the beam. They have a little video about how their wrench reaches something a snap on can't. Well I've been in that situation, and the reverse where I wished my tektons were snap ons.

Thicker beam on the tekton also makes them a little less dainty for flipping in tight areas.

Thanks, I appreciate the response and I'm sure others do.

 

[jsmeece]

Anybody have the Capri set?

 

[WWheeler]

I have an 18pc metric set from Tekton that have been nothing but great. The 30/60 degree work perfect where my old set of Armstrongs (15/30) couldn't. I'll be replacing my old SAE set with Tekton before long also.

As far as the shape of the beam they are comfortable to me. They are nowhere near as squared-edge or uncomfortable to pull hard on as the newer Proto DBE wrenches that we have to use at work every day. Not even close.

 

[Southernbuild]

I received mine yesterday. Also, ordered from Home Depot, they shipped directly from Tekton. Very fast shipping.

The wrenches look great, they should be perfect for my hydraulic needs.

A 30 / 60 degree set made in USA at this price point is a steal, better place your orders before the price goes up in a few days!

 

[oldschoolcraft]

I’m torn on these. They’re made in US but they’re also cnc instead of forged. I think I’d rather they be Taiwan and forged than CNC and MUSA.

And unfortunately other than snapon, for a proper 30/60 4 way angle wrench, these are the only game in town.

 

[Sumboodie]

I have an older Snap On set, I think they are 15* and 60*. It's rare I use them, but handy when needed.
Could have used one yesterday on a 4BT injection pump. The back nut ended up taking me much of the time pulling the pump and installing a new one.

For hydraulics, it's not too common I'm using small wrenches on those. Today I resealed a valve block on an Elgin sweeper, most took a 1.5" wrench. I had to link up another 1.5" wrench, so a ~3.5ft lever and put some serious **** to break them loose.

 

[Tallpilot]

I’m torn on these. They’re made in US but they’re also cnc instead of forged. I think I’d rather they be Taiwan and forged than CNC and MUSA.

And unfortunately other than snapon, for a proper 30/60 4 way angle wrench, these are the only game in town.

Torque Test Channel proved that they aren't as strong as forged so your assertion is correct. However for hydraulic lines the torque requirements usually aren't too high. So it's true the Snap-On is stronger but for most applications it doesn't matter. Also Tekton will happily warranty the wrench if you get a little crazy with it.

From my perspective as only an occasional user of angle wrenches the value proposition is excellent. If I worked on mini excavators all day I might feel differently and justify the cost of forged.

 

[Callelle]

I’m torn on these. They’re made in US but they’re also cnc instead of forged. I think I’d rather they be Taiwan and forged than CNC and MUSA.

And unfortunately other than snapon, for a proper 30/60 4 way angle wrench, these are the only game in town.

Capri makes 30/60s , just not over 24mm / 1"

 

[oldschoolcraft]

Capri makes 30/60s , just not over 24mm / 1"

Wow they do! Thanks! Never heard of them though, are they china or Taiwan? What’s the general quality of the brand?

 

[BukitCase]

AFAIK Capri is Taiwan - I know I bought one of their forged steel vises (a 4" for my TIG table, made in Taiwan and it's almost too pretty to use.

https://www.amazon.com/gp/product/B015NI27ZY/?tag=atomicindus08-20

I looked at Yost til I saw the origin ... Steve

 

[AJHD]

Wow they do! Thanks! Never heard of them though, are they china or Taiwan? What’s the general quality of the brand?

Capri is good to go. On par with Tekton and other offshore Taiwan brands. All my SAE sockets at work are Capri and SAE wrenches are Tekton.

Edit: what are looking to spend on these wrenches? What's your budget?

 

[lardy1]

The Capri site shows they are out of stock of several SAE sizes. It appears the metric range is still covered, though.

 

[Retired dozer fixer]

Torque Test Channel proved that they aren't as strong as forged so your assertion is correct. However for hydraulic lines the torque requirements usually aren't too high. So it's true the Snap-On is stronger but for most applications it doesn't matter. Also Tekton will happily warranty the wrench if you get a little crazy with it.

From my perspective as only an occasional user of angle wrenches the value proposition is excellent. If I worked on mini excavators all day I might feel differently and justify the cost of forged.

If you ever worked on heavy equipment you would know just how tight hydraulic fittings can be. VERY tight. No torque wrench on most. All of you weekend want to be’s haven’t a clue. Old rusty and just plain big. You better have the best wrench money can buy because most of the time you are someplace where if the wrench slips you get hurt. Angle wrenches are nice but larger heavy crows feet on a long handle ratchet work well too

 

[2ndGearRubber]

If you ever worked on heavy equipment you would know just how tight hydraulic fittings can be. VERY tight. No torque wrench on most. All of you weekend want to be’s haven’t a clue. Old rusty and just plain big. You better have the best wrench money can buy because most of the time you are someplace where if the wrench slips you get hurt. Angle wrenches are nice but larger heavy crows feet on a long handle ratchet work well too

Torque spec? Hold breath and brace your core, then crank until your eyes bulge.

Add rust and you're beating the wrench with a sledge.

 

[oldschoolcraft]

If you ever worked on heavy equipment you would know just how tight hydraulic fittings can be. VERY tight. No torque wrench on most. All of you weekend want to be’s haven’t a clue. Old rusty and just plain big. You better have the best wrench money can buy because most of the time you are someplace where if the wrench slips you get hurt. Angle wrenches are nice but larger heavy crows feet on a long handle ratchet work well too

A handful of people make this comment and makes me want to save up for the snap on set. Maybe the cheaper Cat branded one.

Downsides are they are much more expensive and they are not full sets, there’s a lot of skips but the assumption is they are made for the sizes needed.

Though I am tempted to buy a smaller set maybe up to 1/2” of tektons for random project stuff. Maybe some appliance or weird project has a small fastener, not corroded, but limited access, low torque. And Tekton has a lot of sizes that are skipped by snap on.

What size would you say going with snap on makes a difference to need the extra torque? If I was doing tekton for smaller sizes and snapon for bigger, what’s the cutoff?

 

[AJHD]

A handful of people make this comment and makes me want to save up for the snap on set. Maybe the cheaper Cat branded one.

Downsides are they are much more expensive and they are not full sets, there’s a lot of skips but the assumption is they are made for the sizes needed.

Though I am tempted to buy a smaller set maybe up to 1/2” of tektons for random project stuff. Maybe some appliance or weird project has a small fastener, not corroded, but limited access, low torque. And Tekton has a lot of sizes that are skipped by snap on.

What size would you say going with snap on makes a difference to need the extra torque? If I was doing tekton for smaller sizes and snapon for bigger, what’s the cutoff?

An expensive but still cheaper option than buying directly from Snap On, is buying the CAT branded version from your local CAT dealer.

They have a 14-piece set from 3/8" to 1-1/4", or broken into two smaller 7-piece sets... 3/8" to 3/4" and 13/16" to 1-1/4"

 

[82355]

A handful of people make this comment and makes me want to save up for the snap on set. Maybe the cheaper Cat branded one.

Downsides are they are much more expensive and they are not full sets, there’s a lot of skips but the assumption is they are made for the sizes needed.

Though I am tempted to buy a smaller set maybe up to 1/2” of tektons for random project stuff. Maybe some appliance or weird project has a small fastener, not corroded, but limited access, low torque. And Tekton has a lot of sizes that are skipped by snap on.

What size would you say going with snap on makes a difference to need the extra torque? If I was doing tekton for smaller sizes and snapon for bigger, what’s the cutoff?

Snap On has skips?

I saw Cornwell was selling 30/60 angle wrenches now.

Martin

 

[RedneckWelder]

If you ever worked on heavy equipment you would know just how tight hydraulic fittings can be. VERY tight. No torque wrench on most. All of you weekend want to be’s haven’t a clue. Old rusty and just plain big. You better have the best wrench money can buy because most of the time you are someplace where if the wrench slips you get hurt. Angle wrenches are nice but larger heavy crows feet on a long handle ratchet work well too

This has been my experience with hydraulic fittings more often than not as well. The mechanic before you always seems to be a ******* beast on over fighting and then the rust is just cake on top.

 

[oldschoolcraft]

Snap On has skips?

They start at 10mm whereas tekton starts at 6mm. Snap on skips 20mm and 23mm which tekton does have.

Both snap on and tekton skip 25mm which is disappointing to me because my OCD likes to get tool sets in no skips to 1” and 25mm is the highest metric size below 1” (which is 25.4mm)

 

[Steve_P]

Torque Test Channel proved that they aren't as strong as forged so your assertion is correct. However for hydraulic lines the torque requirements usually aren't too high. So it's true the Snap-On is stronger but for most applications it doesn't matter. Also Tekton will happily warranty the wrench if you get a little crazy with it.

From my perspective as only an occasional user of angle wrenches the value proposition is excellent. If I worked on mini excavators all day I might feel differently and justify the cost of forged.

Tekton's own data shows that Snap On is only very slightly stronger, a few percent, in larger sizes. But this does not mean that forging is superior, it means that the Snap On wrench is slightly stronger. There are too many variables here to say that forging is stronger than machined from plate in this case- different wrench design, maybe different material, maybe different hardness... It's apples and oranges.

Metric Angle Head Open End Wrench Set (16-Piece) | TEKTON | WAE91202

Includes: 10-27 mm (Metric) angle head wrenches with 30° and 60° open ends. Made in USA. Comes with holder. WAE91203.

www.tekton.com

 

[82355]

They start at 10mm whereas tekton starts at 6mm. Snap on skips 20mm and 23mm which tekton does have.

Both snap on and tekton skip 25mm which is disappointing to me because my OCD likes to get tool sets in no skips to 1” and 25mm is the highest metric size below 1” (which is 25.4mm)

Ah, Metric.

I was thinking standard, as that is my main use of angle wrenches. I know the one Snap On set skips 1-3/16", but you can buy it separately.

Martin

 

[BarrelRoll]

I guess I should bump this. After hating my William's set and buying 1 Tekton still not liking it enough to order a set. I got bored on a hitch of nights and bought a used set of snapon angle wrenches one at a time on e-bay for much less than retail. Holy cow, well worth the money. They are a great wrench for their purpose. I have no worries about giving them a whack with a dead blow or double wrenching them.

As far as the no skips go there reaches a point where it's just annoying to drag around extra wrenches/ sockets, they take up a lot of tool box room, and the cost is high enough the money you spent on not skipping sizes could buy something useful with. Especially over 1"/ 24mm. I bought a Tekton combination no skip wrench set 25 to 32mm, the only wrenches I use out of it are 27, 30, and 32mm, the rest of the wrenches just take up tool box space.

 

[CHI_Tool&Die]

I would just google or use a reference nut/bolt/threaded fastener size chart and grab the Snap-on ones that correspond with the sizes you would encounter. I don’t think Snap-on gives you any savings if you buy individual vs a set. I’ve started doing this at work (though not with Snap-on) and it saves a ton of space and you don’t have all these rarely if ever used sizes sitting around doing nothing.