I'd stick them in some Evaporust and that paint should come right off. Those line wrenches are damn expensive so if you needed them that is a good deal despite the poor cosmetic condition.
2026 Garage Sale Thread (15th Annual)
- Thread starter Provincial
- Start date
I'd stick them in some Evaporust and that paint should come right off. Those line wrenches are damn expensive so if you needed them that is a good deal despite the poor cosmetic condition.
JonahBrown
Well-known member
- Joined
- May 5, 2025
- Messages
- 106
WisJim
Well-known member
If I go to a tool meeting and sell anything close to what I spend, I figure it's a good day. But we don't have much for flea markets or other sources of interesting tools except garage sales, and the pickings are usually slim at those too. I'm envious of those of you who have regular flea markets--I mostly wait for the semiannual M-WTCA area meetings which are about a 2 hour drive from me.
Outlawmws
Well-known member
Simple green, especially warm/hot will quickly strip most paints, and de-grease the tools. you want the grease off before evaporust
Lye (Oven cleaner) also works well for this but you need PPE for sure. Note that the "low odor" OC is almost useless; the OC must be the real stuff and needs to be outside and with PPE
I prefer this stuff for a lye soak - the are several brands that are 100% lye:
d42jeep
Well-known member
That was supposed to be sarcastic. I’ve never seen another Baker hacksaw. It looks like some Powr-Kraft hacksaws though.
-Don
JonahBrown
Well-known member
- Joined
- May 5, 2025
- Messages
- 106
I haven’t tried that one before, only the original easy off oven cleaner. Works great on lead paint!Simple green, especially warm/hot will quickly strip most paints, and de-grease the tools. you want the grease off before evaporust
Lye (Oven cleaner) also works well for this but you need PPE for sure. Note that the "low odor" OC is almost useless; the OC must be the real stuff and needs to be outside and with PPE
I prefer this stuff for a lye soak - the are several brands that are 100% lye:
Beerhippie
Well-known member
The active ingredient in oven cleaner is lye--sodium hydroxide. I prefer to save a few $ and cut to the chase. A hot solution works best, and a hot solution (~1 cup lye to 1 gallon hot water (and do what you oughter, add the lye to water)) in an ultrasonic cleaner works best.
Went with a mate to a house clearance centre for a mooch - he brought us both a full English breakfast (don’t google that if your calorie conscious) and I provided the four wheels and fuel. Undoubtedly bargains to be had in every dept…. except obviously bar the tools 
Still it was a grand day out in a cold and damp January and we ere rifling through junk for 4 hours so quiet enjoyable. Anyhow for £10 ($13.65) I came away with following:
Black Decker WM450 Workbox (I think these are shopbox in GJ land) in a thoroughly enjoyed condition, yet still completely rancid and functional. Years long Itch scratched with this purchase, but realistically something I don’t need, we all know that feeling
I think a quick scrub up and an ebay listing beckons.
Inside was the following - Blue point right angled snips, Spanish Irega 10” adjustable, Irwin pliers and a couple of York KG weights (not pictured two hard back woodwork books that were part of the deal). All tools I’d guess had been somewhere damp - yet the box was dry, with sawdust to prove it?!
Still they all scrubbed up nicely, even though sadly the snips have a little bite out of one of the cutting edges. Seem to cut just dandy though on a thin piece off alloy I tried. Stamped as DAR 9A USA I’d be intrigued how old they are.
Left behinds included a set sharp edges, waxed 180 K2 carving skis (unusal find in England!) and a very new looking and tidy Draper bench mounted bandsaw which worked great when I tested it, then failed when my mate switched it on, so possibly a bullet dodged there - £30 ($41) with is about a 5th of retail. It might have been an easy fix but I’m inclined to doubt it…
Still it was a grand day out in a cold and damp January and we ere rifling through junk for 4 hours so quiet enjoyable. Anyhow for £10 ($13.65) I came away with following:
Black Decker WM450 Workbox (I think these are shopbox in GJ land) in a thoroughly enjoyed condition, yet still completely rancid and functional. Years long Itch scratched with this purchase, but realistically something I don’t need, we all know that feeling
I think a quick scrub up and an ebay listing beckons.Inside was the following - Blue point right angled snips, Spanish Irega 10” adjustable, Irwin pliers and a couple of York KG weights (not pictured two hard back woodwork books that were part of the deal). All tools I’d guess had been somewhere damp - yet the box was dry, with sawdust to prove it?!
Still they all scrubbed up nicely, even though sadly the snips have a little bite out of one of the cutting edges. Seem to cut just dandy though on a thin piece off alloy I tried. Stamped as DAR 9A USA I’d be intrigued how old they are.
Left behinds included a set sharp edges, waxed 180 K2 carving skis (unusal find in England!) and a very new looking and tidy Draper bench mounted bandsaw which worked great when I tested it, then failed when my mate switched it on, so possibly a bullet dodged there - £30 ($41) with is about a 5th of retail. It might have been an easy fix but I’m inclined to doubt it…
Hit an Estate Sale Saturday. I think the guy took apart everything he ever had and saved any potentially useful pieces in little boxes. Lots of little boxes. Lots. Tools were few. I suspect family got them, because there was no sign of them in the pictures.
The Plumb DOE is twice the thickness of the combination wrench. I'd think carbon steel but Alloy Artifacts indicates the stamp is too late.
Traintor Positive #7 sawset. I've already got a nicer one, but they are cool. A tap handle from someplace out in Lancaster County. A pugh auger bit from Philly that probably isn't worth saving. And what looks like a blade from a Stanley 66 beader (I'll have to dig mine out to be sure). No sign of the beader or other blades. I'll put it with the single blade that came with mine, and the one I made for it.
Not shown are two morse taper #1 drill bits. There was also a Bonney socket that google says was for oil pressure senders, but cleaning revealed it had welding slag or something on the inside of it and I tossed it right into the scrap metal pile.
The Plumb DOE is twice the thickness of the combination wrench. I'd think carbon steel but Alloy Artifacts indicates the stamp is too late.
Traintor Positive #7 sawset. I've already got a nicer one, but they are cool. A tap handle from someplace out in Lancaster County. A pugh auger bit from Philly that probably isn't worth saving. And what looks like a blade from a Stanley 66 beader (I'll have to dig mine out to be sure). No sign of the beader or other blades. I'll put it with the single blade that came with mine, and the one I made for it.
Not shown are two morse taper #1 drill bits. There was also a Bonney socket that google says was for oil pressure senders, but cleaning revealed it had welding slag or something on the inside of it and I tossed it right into the scrap metal pile.
bmwrd0
Well-known member
On Saturday I went out, but where to go was the question. Not much of interest locally, nor in the city to the north. But, down south a ways was an estate sale that looked kind of interesting, plus the good used tool shop is down that way... So, off I go!
The ES didn't start until 11(?!) so I hit the used tool shop first, where I picked up a Stanley sweet hart boxwood ruler and the largest size Rigid pipe cutter that they make, as I need it for an up coming project. Those set me back $20, no mean feat considering the Rigid when new runs $500. Heck, the cutting wheel for these are $50+. Not much call for them, which is probably why he let it go so cheap...
When I hit the estate sale, I made a bead for the shop, and found myself surrounded by cheap tools at very dear prices. And, as this was the second day, picked through for the most part. But I did find (and pay too much for) the Stanley 39 1/4" and a Walden 66041/2 speeder.
All in all an OK day.
The ES didn't start until 11(?!) so I hit the used tool shop first, where I picked up a Stanley sweet hart boxwood ruler and the largest size Rigid pipe cutter that they make, as I need it for an up coming project. Those set me back $20, no mean feat considering the Rigid when new runs $500. Heck, the cutting wheel for these are $50+. Not much call for them, which is probably why he let it go so cheap...
When I hit the estate sale, I made a bead for the shop, and found myself surrounded by cheap tools at very dear prices. And, as this was the second day, picked through for the most part. But I did find (and pay too much for) the Stanley 39 1/4" and a Walden 66041/2 speeder.
All in all an OK day.
3baygarage
Well-known member
Saturday morning I was out the door early and off to the the flea market(s). It was slightly chilly out. Decided to hit the tiny outdoor flea first, hoping to catch some good deals. Half way there, a light drizzle started. Oh no! Arrived to see a few cars zipping away and but one lone vendor frantically packing up!
I decided to head over to the other small outdoor flea. Figured there had to be a lot going on there as it’s the better of the two. One vendor in the parking lot! Probably the only person with a tent. Seemed he had nothing much so I didn’t get out of the car.
I parked way off and started scrolling for estate sales. The couple i liked the look of were too far as I had to be home in a couple hours. In fact, there were no close estate sales. Not many garage sales due to cold this week.
Surprisingly on CL I see a Trash & Treasure sale at one of them there “old people colonies” aka country club a few miles away. Hmmm, perfect! My last hope. Could be really lame, but it was my only option for the day.
Well, I drove up shortly after the 8am opening time, and it was a madhouse! Volunteers directing traffic and nowhere to park. People all around were leaving with bags and arms full of stuff.
Well, I made my way into the room of books, the room of fine china, and finally to the main event room. It was mobbed! I think every white head of hair in town had to be there. I was definitely one of the youngest attendees.
The place was full of tables or stations. First one I see said tools. Sweet! Well, there was stuff. Fishing, hardware. Only one big bin of hand tools, and some old guy had dropped anchor there. Hand tools were 50 cents each. He bought just about every single hand tool, mostly pliers,leaving just a few screwdrivers and misc. items. He def filled a bag. I walked around the table and waited my turn. Didn’t look like I missed anything great. Finally he stepped away and I moved on in. I pulled out a pair of dikes and the guy came right back and said “I’d buy them.” “I’ll take them if you don’t”. I didn’t see a name but they were quality. I told the guy I didn’t need them, he could have them. He said he needed them. Guy was likely in his 80’s. Maybe new in town and and needed tools
I sure didn’t need them.
He did leave one interesting thing in the bin that I almost missed too. It blended in with the big stuff. A little 2” aluminum vise. No name or markings whatsoever. The man running the tool table seemed a little pushy and eager to sell everything. However, for 50 cents it was mine. I see the same exact vise on ebay, no markings.
Then it was on to the rest of the room. Most tables were manned by….two or three nice little old ladies. Some were a little pushier than others. The prices of everything in the room was amazingly cheap, and mostly usable donated stuff, hence all the people leaving with piles when I arrived. Any way, I walked around a bit and found a few more goodies.
Lego set $1, vise .50, headphones $1, half full 3in1 shorty oil can .25 , small Androck kitchen grinder .50, yellow enameled cast iron pan- no markings $3.
I picked up the grinder and this little old lady (shopper) tells me it’s an antique and she has one just like it. I asked her if it was for coffee and she told me it’s for nuts. Sundaes then, i said. It’s always nice to learn from the older generation. Pretty much how I learned about tools.
The pan was funny. I looked at it twice. Three women behind the tabl. Ended up talking to one of the ladies behind about it who schooled me on cast iron cleaning. I didn’t buy it, the price was right, but I was still shopping. I went back to it a third time to check it out, and another old lady with a name tag on pops up next to me and tells me I can give her the money. She asks how much and I tell her $4. She says “Just give me 3. These other ones here don’t want to deal!”. I paid her and by the time I turn around the other lady I had spoken to was whispering in the ear of a third woman about her. I could tell there was some beef between them. Some catty drama. I wasn’t surprised. I mean after all, this place, although disguised as a country club, seemed more like a glorified trailer park with new double and triple wides, and I assume everyone still in everyone’s business.
After buying the small oil can for 25 cents that had been bundled as part of some craft stuff at another table, I made my way out of the crowd and relinquished my parking spot to another happy shopper.
I decided to head over to the other small outdoor flea. Figured there had to be a lot going on there as it’s the better of the two. One vendor in the parking lot! Probably the only person with a tent. Seemed he had nothing much so I didn’t get out of the car.
I parked way off and started scrolling for estate sales. The couple i liked the look of were too far as I had to be home in a couple hours. In fact, there were no close estate sales. Not many garage sales due to cold this week.
Surprisingly on CL I see a Trash & Treasure sale at one of them there “old people colonies” aka country club a few miles away. Hmmm, perfect! My last hope. Could be really lame, but it was my only option for the day.
Well, I drove up shortly after the 8am opening time, and it was a madhouse! Volunteers directing traffic and nowhere to park. People all around were leaving with bags and arms full of stuff.
Well, I made my way into the room of books, the room of fine china, and finally to the main event room. It was mobbed! I think every white head of hair in town had to be there. I was definitely one of the youngest attendees.
The place was full of tables or stations. First one I see said tools. Sweet! Well, there was stuff. Fishing, hardware. Only one big bin of hand tools, and some old guy had dropped anchor there. Hand tools were 50 cents each. He bought just about every single hand tool, mostly pliers,leaving just a few screwdrivers and misc. items. He def filled a bag. I walked around the table and waited my turn. Didn’t look like I missed anything great. Finally he stepped away and I moved on in. I pulled out a pair of dikes and the guy came right back and said “I’d buy them.” “I’ll take them if you don’t”. I didn’t see a name but they were quality. I told the guy I didn’t need them, he could have them. He said he needed them. Guy was likely in his 80’s.
Maybe new in town and and needed tools I sure didn’t need them.He did leave one interesting thing in the bin that I almost missed too. It blended in with the big stuff. A little 2” aluminum vise. No name or markings whatsoever. The man running the tool table seemed a little pushy and eager to sell everything. However, for 50 cents it was mine. I see the same exact vise on ebay, no markings.
Then it was on to the rest of the room. Most tables were manned by….two or three nice little old ladies. Some were a little pushier than others. The prices of everything in the room was amazingly cheap, and mostly usable donated stuff, hence all the people leaving with piles when I arrived. Any way, I walked around a bit and found a few more goodies.
Lego set $1, vise .50, headphones $1, half full 3in1 shorty oil can .25 , small Androck kitchen grinder .50, yellow enameled cast iron pan- no markings $3.
I picked up the grinder and this little old lady (shopper) tells me it’s an antique and she has one just like it. I asked her if it was for coffee and she told me it’s for nuts. Sundaes then, i said. It’s always nice to learn from the older generation. Pretty much how I learned about tools.
The pan was funny. I looked at it twice. Three women behind the tabl. Ended up talking to one of the ladies behind about it who schooled me on cast iron cleaning. I didn’t buy it, the price was right, but I was still shopping. I went back to it a third time to check it out, and another old lady with a name tag on pops up next to me and tells me I can give her the money. She asks how much and I tell her $4. She says “Just give me 3. These other ones here don’t want to deal!”.
I paid her and by the time I turn around the other lady I had spoken to was whispering in the ear of a third woman about her. I could tell there was some beef between them. Some catty drama. I wasn’t surprised. I mean after all, this place, although disguised as a country club, seemed more like a glorified trailer park with new double and triple wides, and I assume everyone still in everyone’s business. After buying the small oil can for 25 cents that had been bundled as part of some craft stuff at another table, I made my way out of the crowd and relinquished my parking spot to another happy shopper.
Outlawmws
Well-known member
Good picking 3 bay! I'm still on the lookout for a short 3 in 1 can like that.
Vise looks pretty solid for aluminum.
Vise looks pretty solid for aluminum.
four.cycle
Well-known member
It's a nut grinder.
We had one in the house when I was a kid.
"Androck" was the trade name used by the Washburn Company of Worcester, Massachusetts.
They made can openers, peelers, potato mashers, and... nut grinders, among other things.
3baygarage
Well-known member
I've seen the name on kitchen utensils before. In this case it's actually on the bottom of the jar.
four.cycle
Well-known member
^ "Androck" was one of the more popular product lines of basic kitchen utensils. Some of their stuff has a "collector" market.
They held a patent on the pastry blender:
They held a patent on the pastry blender:
Attachments
OP
Provincial
Well-known member
I had a Honda 20-HP V-twin seize an aluminum connecting rod to the crankshaft, galling aluminum to the rod journal, which was otherwise serviceable. I used drain cleaner to soak the aluminum and eat it up, leaving the journal just as good as new.Simple green, especially warm/hot will quickly strip most paints, and de-grease the tools. you want the grease off before evaporust
Lye (Oven cleaner) also works well for this but you need PPE for sure. Note that the "low odor" OC is almost useless; the OC must be the real stuff and needs to be outside and with PPE
I prefer this stuff for a lye soak - the are several brands that are 100% lye:
gearhead1960
ALLIANCE MEMBER
I love Androck stuff. Here's a couple of examples in active use in our kitchen. Whenever I see them at ES, I buy them......
four.cycle
Well-known member
Not sure if you've already dealt with this, but:
Undiluted Simple Green WILL remove paint from tools.
a6hux
Well-known member
Missing a 1/2 socket but for $12 I couldn’t pass it up!
knock knock
Well-known member
- Joined
- Nov 30, 2024
- Messages
- 80
Bought some wrenches off fbm this week and the seller reached out to let me know he had some more snapon for sale. Guy cleans out estates and gets all kinds of interesting things. Was really only after the fhx80 but not a terrible deal. Lots more cleaning when I make it to the garage.
Attachments
Last edited:
d42jeep
Well-known member
In checking EstateSales.Org and Craigslist the upcoming sales in the area didn’t look interesting at all through the weekend. The only one that stood out today was one in San Lorenzo which is getting close to encroaching into Outlaw‘s territory. The sale had more drill bits than I could believe but there was quite a bit of Powr-Kraft and Craftsman as well. I managed to leave all the drill bits behind although I picked up a Dunlap hand drill. 
Powr-Kraft tools
Cleaned up the hex set.
Craftsman tools
Millers Falls wood chisel.
Coes monkey wrench.
Large Diamond auto wrench with possible railroad markings.
Ace Hanson easy outs.
-Don
Powr-Kraft tools
Cleaned up the hex set.
Craftsman toolsMillers Falls wood chisel.
Coes monkey wrench.
Large Diamond auto wrench with possible railroad markings.
Ace Hanson easy outs.
-Don
Outlawmws
Well-known member
Nice score Don! and I missed that one. I'll try to see what leavings are are tomorrow since it's so slow these days.
alinc100
Well-known member
Nicely done. The Snap On scaffold ratchet could likely get you most of your investment back
gearhead1960
ALLIANCE MEMBER
….speaking of Androck, found this at an ES today…I love Androck stuff. Here's a couple of examples in active use in our kitchen. Whenever I see them at ES, I buy them......
Outlawmws
Well-known member
Well, that was my only score today, and these were the leavings I grabbed:
It is picking up a tiny bit. great weather; its in the 70's here, but not a lot of sales. One Estate sale produced:
Wood chisel I'm working on the maker, a Stanley #9-1/4 block plane, a Goodell Pratt eggbeater drill with hollow metal handle for the bit (it unscrews from the frame), Fine Wire wheel bundle - I think 4 wheels, a stop for a 2X clamp bar, small funnel, a Cornwell flair wrench - 9/15 & 1/2, and a Jorgensen 3" wing nut C clamp. $15 all:
I had a heck of a time getting te Joregensen markings to sow buried and filled with putty... Got it somewhat out and chalk brought it up readable...
Closeup of the Arrow in a Diamond -I believe its the Shapleigh Hardware Diamond Edge (DE) TM.
We hit a total of six sals in the last couple of days do inventory. I’m working on not hoarding stuff I don’t need just because it’s a good deal.
I have a hard time with certain things, however. Hammers are one of them. I have a soft spot for US made hammers. They are rarely abused, always cheap.
I found the little 8oz Stanley tack hammer at a small sale within a bunch of craft supplies. It’s kind of odd that it has a Stanley USA head with a handle marked “Ridgid.” I’m assuming Ridgid relabeled Stanley hammers at one point?
The Proto and Craftsman ball peins were at a different sale. Both are in good shape with good handles.
I’ve go $6 total in three hammers.
I have a hard time with certain things, however. Hammers are one of them. I have a soft spot for US made hammers. They are rarely abused, always cheap.
I found the little 8oz Stanley tack hammer at a small sale within a bunch of craft supplies. It’s kind of odd that it has a Stanley USA head with a handle marked “Ridgid.” I’m assuming Ridgid relabeled Stanley hammers at one point?
The Proto and Craftsman ball peins were at a different sale. Both are in good shape with good handles.
I’ve go $6 total in three hammers.
Outlawmws
Well-known member
That "tack hammer" is actually a sheet metal workers hammer.
bmwrd0
Well-known member
Outlaw, I think that G-P drill might be a surgeons drill. Check the number on it, and if it is 315 you found one.
I wasn’t completely sure, I just didn’t have a better name for it. Thanks!
Outlawmws
Well-known member
Labeled Goodell-Pratt Company GreenField Mass. USA on both the flat turn handle and the chuck. The chuck has a patent date of Aug 13, 1895 as well. So far, no model No.
Outlawmws
Well-known member
Labeled Goodell-Pratt Company GreenField Mass. USA on both the flat turn handle and the chuck. The chuck has a patent date of Aug 13, 1895 as well. So far, no model No.
The 315 had the same metal grip/bit safe, but the chuck is different.
based on this page I think its a #49?
Seems to be at least 3 that used this metal grip #49 (three jaw Chuck), #110, (2 jaw chuck) , 315 (set screw chuck)
RTM
Well-known member
Yup, and probably a Stanley made. DE in-licensed good stuff, like KK and others.
WisJim
Well-known member
Yes, it's a #49. I like mine, it's handy with smaller bits. The #110 is interesting, same size as the 49 but it takes the same bits as the early Goodell Pratt push or reciprocating drills, the ones with a sort of cross shaped base.The 315 had the same metal grip/bit safe, but the chuck is different.
based on this page I think its a #49?
Seems to be at least 3 that used this metal grip #49 (three jaw Chuck), #110, (2 jaw chuck) , 315 (set screw chuck)
It actually says “Stanley Made in USA”, so older than “Stanley USA”, but the Ridgid handle looks newer - I think it is a replacement handle.It’s kind of odd that it has a Stanley USA head with a handle marked “Ridgid.” I’m assuming Ridgid relabeled Stanley hammers at one point?
That’s a great score!
I considered that but the head sure doesn’t seem as though it’s seen enough use to need a handle.
Neat stuff regardless
Patrickm82
Well-known member
Grabbed this old 5 drawer machinist chest for $20 last night off market place. No big cracks or splits anywhere, the bottom drawer is missing its side rails but no big deal. Unfortunately the guy sanded a spot for some reason! Needs some new felt but otherwise pretty good shape. Missing the front panel as well.
Outlawmws
Well-known member
Looks like a nice project Patrick!
ctuai
Well-known member
Estate sale ($50): Sony CCD-TRV37 Video 8 camera; Parris double barrel cap gun (Savannah, TN) ; Craftsman crown 6500 toolbox; Witte's 3.7lbs IXL double bit axe head; War rations book w/ 3 books; Trombone mute; Braun type 47 percolator coffee maker; Virginia Metalcrafters 9.5" sundial (Waynesboro, VA).
Video cams and cameras have good value as it turns out the zoomers (gen z) like "old school" cameras. Got the tool box for all the jewelry / watchmakers gear I'm accumulating. The cap gun trigger fires each hammer separately and also has a half-**** position. It's supposed to be a replica, but have no idea of what. The Krupps portable percolator makes surprisingly good coffee. Probably helps that I use Timmy Horton coffee
Last edited:
Outlawmws
Well-known member
You guys are doing good! I'm living vicariously through you since today went dead (2 "been there done that already" sales, but the rest aren't' worth getting out the door.)
ctuai
Well-known member
Time to process all that gear that's just a hangin about, or finish up that almost finished project, or watch Canada dominate mixed doubles curling. A blessing, I say... then again, I just spotted a Wilton baby bullet listed at an upcoming local auction, current bid is $2 so, admittedly it's nice finding stuff also
Last edited: