To avoid these ads, REGISTER NOW!

Getting toolbox off of pallet?

I

IFMJohn

Well-known member
Joined
Jun 6, 2014
Messages
990
Location
Tacoma, WA
This may be a dumb question, I haven't slept in over a day so forgive me if I'm not the most "with it" right now.

My matco double bay just came in. He set it in my garage and took off. I've got a toolbox sitting on a pallet. My original idea was just to roll it off the pallet. They've installed 2x4s in front of the wheels to keep it from moving. I don't have any other guys here to help me and I'm not from the area so I don't really know anyone here. Do you guys just break those 2x4s off and roll it off the pallet?

I'm tempted to just grab my big pry bar but I don't want to damage my box.
 
To avoid these ads, REGISTER NOW!
OP
I

IFMJohn

Well-known member
Joined
Jun 6, 2014
Messages
990
Location
Tacoma, WA
4u6ytabu.jpg

e8egu4y5.jpg
 
Last edited by a moderator:
OP
I

IFMJohn

Well-known member
Joined
Jun 6, 2014
Messages
990
Location
Tacoma, WA
I'm a big guy. It's a big box. Lol. I'm in a retirement community at the moment while I finish school. I don't think I can walk next door and grab a 70 yr old man to help me
 
Z

Zeke

Well-known member
Joined
Aug 13, 2009
Messages
17,176
Location
Long Beach CA, the sewer by the sea.
Use some of the wood to make ramps. Or just grab a Sawzall and cut everything away. Then make a lever and fulcrum out of the waste lumber and kick out what is left.

Lots of ways to skin this cat.
 
H

Hiball

Well-known member
Joined
Apr 30, 2009
Messages
14,029
Location
Missery
I would simply knock the 2/4's that are keeping the box on the pallet then push the box off, if it makes you feel better simply use 1 2x4 on its side to step the box down a bit. I've re-railed box cars using scrap lumber to climb it back up on the rail so going down should be a breeze.. :)
 
OP
I

IFMJohn

Well-known member
Joined
Jun 6, 2014
Messages
990
Location
Tacoma, WA
I was worried about the weight of the box dropping the 4"or so onto the casters. Apparently I am strong enough to lift one end at a time. So I lifted one end and rolled it off and set it down and then did the other end.

I did spend more time typing than doing. Haha. I didn't want to break my box 5 minutes after out was delivered.
 
D

David W

Banned
Joined
Apr 4, 2011
Messages
1,353
Location
K.C. MO
Did you remove the drawers to lighten the load before doing this?
Nice box, I hope you like it.
 
To avoid these ads, REGISTER NOW!
R

redwrench60

Well-known member
Joined
Sep 10, 2011
Messages
6,069
Location
East Tennessee
It'll be fine. Pro boxes are tougher than that. They're made to bump and bounce over shop floor drain grates and pavement seams.
 
D

DWise

Well-known member
Joined
Apr 22, 2012
Messages
322
Location
Newark, Ohio
IFMJohn said:
I'm a big guy. It's a big box. Lol. I'm in a retirement community at the moment while I finish school. I don't think I can walk next door and grab a 70 yr old man to help me
Click to expand...

I'm getting close to 70 and I think I could have unloaded it by myself. We are not as frail as we look. :)
 
W

Wamsutta

Well-known member
Joined
Jan 8, 2014
Messages
10,879
Location
Amarillo, Texas
When you get your triple bay some day, you can ease one side down at a time with a floor jack and a block of 2 x 6.
 
T

tarbellb

Well-known member
Joined
Apr 17, 2011
Messages
5,759
Location
Oregon
Id probably ask the 70yr old guy in his garage before the 23yr old watching tv.
 
C

chadster1

Well-known member
Joined
Aug 25, 2009
Messages
4,023
Location
Terrell, Texas
Wamsutta said:
When you get your triple bay some day, you can ease one side down at a time with a floor jack and a block of 2 x 6.
Click to expand...

I always just yanked real hard and let them bounce off the floor when unloading them off the pallet. Of course, I was always dealing with Snap-on boxes.

Seriously, if a roll cab cant handle the 4" drop from being unloaded off of a pallet EMPTY, then its not worth having.
 
You must log in or register to reply here.
To avoid these ads, REGISTER NOW!
Top Bottom