Recent content by Chevy72pu

  1. C

    Pressure washer question.

    I have been looking at replacement pumps for my home, gas powered pressure washer. I noticed that they all have a notation on the description of 130 to 150 max hours. Is this referring to running Time? Warranty limit? Life of the pump? I seriously don't know what it means. Thanks in advance.
  2. C

    What did you do "IN" your garage today?

    Finally got around to some maintenance jobs on the 1990 Snapper RER. New 33" blade, new air filter and prefilter, new friction disc and new left side axle boot. Bought this mower new in 1990. It is on it's third engine, third deck, and second rear diff but it keeps on going.
  3. C

    What did you do "IN" your garage today?

    Recently I noticed that the golf cart was making a scrubbing sound when turning. I investigated and found that the leaf spring bushings needed to be replaced. One pic is the new ones I installed. One pic is what was left of an old one. I think it was time to change them.
  4. C

    Hitch receiver storage ?

    I have two of these in my pickup bed. One holds all of my hitches and pins.
  5. C

    Need help with wiring, Campbell Hausfeld 8 gal wall mount , pulled cover replaced regulator and the 4 wires that go to back of on/off switch came off

    I realize it is too late for this time, but in the future snap a pic with your phone before removal or disassembly. It makes reassembly a snap.
  6. C

    Not your typical garage post

    Low and off do not work as intended. Otherwise they would come on during the first time I cycle through the settings. Instead the low setting works as I start pressing the button the second time . Will see if I can find the diagram.
  7. C

    Not your typical garage post

    My original post stated "Recently the vent fan will only operate on low speed after you push the power button through a low, high and off cycle then push it again. " So no, it doesn't start on the high position. It come on in the low position and only runs at low speed even if I press the power...
  8. C

    Not your typical garage post

    Thanks Zeke. I have visually checked the control panel and see nothing burned out on it or gumming it up. So I guess the next thing is to pull the motor from under the stove and check it for grease. The filter was in pretty bad shape so that may be it.
  9. C

    Not your typical garage post

    I have tried Google and You Tube. Both of them seem to assume that I have already diagnosed the problem and proceed to tell me how to repair it.
  10. C

    Not your typical garage post

    So this is in the kitchen, not the garage. But I suspect someone on here has already dealt with this issue. We have a Jenn Air slide in oven with a downdraft exhaust. Recently the vent fan will only operate on low speed after you push the power button through a low, high and off cycle then push...
  11. C

    Above 1200 Sq/FT BoostingAZ's Garage & Woodshop

    Sorry to hear about your dog. Maybe you can go ahead and get a young dog to befriend his brother before the time comes. OTH we had a male Golden Retriever who died suddenly overnight at 5 years old. His sister lived to 9 yoa and never seemed to miss him.
  12. C

    Riding mowers and dust.. ideas on reducing?

    Sorry, didn't mean mine as a joke but I see how it happened. I run my irrigation system for one hour every other night. So in my mind I was saying to water during tonight and mow tomorrow afternoon. But since you mow 6-8 acres I'm guessing you don't irrigate all of it.
  13. C

    Riding mowers and dust.. ideas on reducing?

    Run your irrigation system 24 hours before mowing.
  14. C

    Any one plant a food plot? Tractor attachments?

    We have good sandy soil. We mow the plots in the summer with a swisher cutter behind a four wheeler. Then harrow them once or twice with a pull harrow behind a kubota s x s. In September we Broadcast Plant a combination of wheat and turnips again wih the four weeler followed by some 10-10-10...
  15. C

    What did you do "IN" your garage today?

    My dad passed in 2004 at age 78. I have quite a few of his tools in my shop. One was an old push plow that he used in laying off the rows in his garden. I had used it as yard art until the handles rotted. It has been sitting in a corner for several years. He had obtained a replacement set of...
Top Bottom