Search results

What is the difference between sandblasting guns? I see them from 20 to 300. I have a cheap hf cabinet, don't like the guns that come with it. I have tried a couple other cheap guns and they sucked too. I wouldn't mind buying a better one but don't want to if doesn't work any better. I am also...

Anyone know what this is? Both ends are 1/2". Onlyh markings are 599 569. Thanks

About 30 years ago I hired a sandblaster to come out and sandblast a car for me. Car was on a rotisserie so I had him blast the bottom, inside floors, door jambs, trunk jamb and engine compartment. It took him a couple hours to do and he only used about 2 bags of sand. A few years later i was...

Trying to figure how this tool works. It is a Snap On MT358B. I saw a listing that says it is a battery post adapter. Can anyone tell or show me how it works? Thanks

Can anyone tell me what these are used for? Wurth micro grip clamp.

I have a 24x36 pole building with three stalls. It has 8' walls but there is no ceiling so it goes up to about 14' at the peak. I looked at some lights online and saw that high bay lights are for 20 to 45' and low bay are for 12'-20. I don't need great lighting for this but do need to be able to...

I need to run some 6/3 wire from my switch to my compressor. Because of vibration I don't want conduit. I looked at some armored cable but the smallest I could find was 25'. I only need a few feet. Ideas? thanks

I want to run power to my detached garage. My house has a 200 amp breaker box, then a sub panel 100 amp box about 60 ft away. I want to hook into that and go about 40' underground to my garage. I have a shop on the other side of property so garage will mainly be lights and door openers but I...

Dumb question time. Can I run power to top or bottom of this switch? The reason I ask is I saw some where it says either way but this one does not. I am pretty sure electricity doesn't know top from bottom.

I am in the process of doing some wiring in my 40x50 building. I was going to run 4 circuits for my welder so I would always have easy access to a plug in. Considering the price for wire, conduit and fittings I am thinking of running only one circuit and using one of these 50 foot cords. Most of...

Has anyone seen these lifts? Price sounds too good to be true, probably a scam? Anyone? https://garageautoequipments.com/product/apluslift-hw-8sxlt-8000lb-4-post-extra-tall-long-wide-portable-storage-service-car-lift/?fbclid=IwAR3_EpoL65mvYf8TTrMbmzsthon1pGLPJu7sW3oyHLsP0YP5kcWfHcxzDCI

I have an old air compressor with a GE 230v single phase 5 hp motor. 32 amps so I am figuring a 40 amp breaker and #8 copper wire? I also will be running a couple lines for my welder. I think 50 amp breaker and #8 wire. Does the length of wire change things? One run would be about 20', the...

New S K tools. Prices do not include shipping. Safety wire kit #7715, $125 Metric T handle set #73389, Sizes 2,2.5,3,4,5,6,8 and 10MM. $25 3/4 ratchet rebuild kit #471709, $10 3/4 drive, 6pt impact sockets 17MM, 84717, $13 19MM, 84719, $13 24MM, 84724, $17 26MM, 84726, $17 38MM, 54738, $25...

For some strange reason whoever built my building (50 years ago) put cement to the inside of the post in my doorway, So the threshold was not on the cement. I need to cement about 6"x6"x36". 2 questions, What is the best to put under it (gravel, sand etc?) Since this will be a separate...

I have a pole building that I had a 16x10 CHI door installed. I don't live at the property so it took a while before I was finally able to see what is happening. I had thought it was leaking under the door but today I was there while it was raining and it is coming in from between the sections...

I am getting ready to wire my shop. I have a 7.5 horse 3 phase air compressor. I am looking at this rotary phase converter. The compressor is 22.5 Amps as is. Once i add the converter will the amps stay the same? What size wire and breaker will I need for this? Thanks...

I have a insulated 10x16 garage door on my pole building. Unless I lift it to about 2/3 way up it will come back down on its own. Is this the way it is supposed to be or should it stay in any position? Thanks

I have a few new SK extension store displays. I am asking $50 each for them plus actual shipping. Shipping will not be cheap as these weigh 17 Lbs each and measure 24x17x9 and will be shipped from zip 60178. Paypal only. Lower 48 states only.

I want to put an outside outlet on my pole building. I have the outside box with the cover. Does this need to be a GFCI or at least fed by one? Thanks

I have 2x6 diagonal braces in my pole building. I will be putting girts in for finishing off the inside. Can I remove the diagonals once I do this or do I need to work around them? Thanks.