Search results

Needed to run my brad nailer today so I fired up my Devilbis 4HP twin tank compressor in my workshop, ran fine for about 2 minutes then sounded like it was dyeing and the motor was struggling. Shut it off and screwed the box I was making together. Later on I decided to troubleshoot the comp...

This C-Man upper and lower is for sale locally. My brother has shown some interest in it. I can't remember when this box was on the floor in Sears. Kind of a crappy pic from Craigslist.

Looking for a granite surface block, 90 degree surface block, 8" height gage with carbide scribe, optical center punch, digital caliper. transfer screw sets, lots of other stuff too. Just a home owner lathe set up. not looking for super expensive tooling.

Looking for a 3 draw grey red Cratftsman middle chest will also buy a 2 drawer Willing to pay fair market value plus shipping for 1 in decent shape. Also looking for the red folding metal side shelf. Also looking for a 3 drawer bottom roller with the sliding door.

A draw from my at home box , Vintage craftsman ratchets that were manufactured in my lifetime. from the pearhead up to a newer set that was still USA made

I've been looking at this, Clore JNC660 'Jump-N-Carry' 1,700 Peak Amp 12-Volt Jump Starter , any comments ? reviews before I pull the plug and buy it.

on Sears.com 4 piece Craftsman drag link socket set $14.96 + shipping Ok to redeem SYW points on too. good buy regardless of coo for the amount of use they're going to get...Item # 00934299000P Model # 34299

Has anyone tried the Loctite freeze an release spray? Does it work as well as the ads say? As quick? this would be a God send in the rust belt. I'm thinking on salt spreaders and snow plows that always seem to break when we need them the most.

9 piece 3/4" drive metric sockets $29.98 with free store pick-up, hard to beat that price for sockets I'll only use 3-4 times a year. PLUS the package says made in USA!!!!! Online store only. And I had no problems with my order today

Bought this vise yesterday, a bit more than I wanted to pay, but still within reality. I want to know everything I can about it. Found out so far it was made by Reed somewhere between 1939-1949. Sold by Sears obviously. 5" jaws. Any help fellow members?

I recently acquired a Logan 1400 metal lathe , I don't know a lot about Logan any input or reviews? Where's a good place to get tooling?

Saw for the 1st time an ad for a Dewalt Mechanics tool sets, sold exclusively at Sears. And was curious so I looked and looked all over the internet to find any info on them . But I couldn't find out the Country of Origin on any site that reviewed them. Can anyone fill this in for me? Is this...

I'm looking for V-series Craftsman socket sets in the factory metal trays. Willing to pay fair market value + shipping, send me a PM with what you have lets negotiate a price. Still looking for 1/2" deep 6 pt.set Any 1/2" metric sets ,1/4" shallow SAE 6 and 12pt. if they made either and any...

I'm looking for V-series Craftsman socket sets in the factory metal trays. Willing to pay fair market value + shipping, send me a PM with what you have lets negotiate a price. Still looking for 1/2" deep 6 pt.set Any 1/2" metric sets ,1/4" shallow SAE 6 and 12pt. if they made either and any...

I'm willing to pay fair market value plus shipping, for v series Craftsman socket sets in metal carry trays. Prefer 6 point but will take metric and 3/8 or 1/4 drive drive in 12 point ,shallow or deep. or 1/2 " drive metric shallow or deep. PM me and lets negotiate!

I need to know what something is called....it's a type of adapter that pushes into a socket so you can use a combination wrench to turn a socket. and who sells a decent black oxide set of 1/4" 3/8" 1/2" and even 3/4" if there's 1 available. I looked in anything I can think of using search...

Where these spinners made in other drives? I have only ever seen the 3/8 drive.

Did the V series 1/4" drive C-man ratchet ever have the oil port or was it only the 3/8" and 1/2 " ? What about the 3/4" drive too?

Always wondered why sockets and wrenches come in metric but the ratchets are always SAE measurment of 1/4" 3/8" 1/2" 3/4" drive, since other countries don't use SAE. Can ayone explain this? I understand that the system was invented in the USA, all I want to know is what it's called in other...

Is this recent? When they were making boxes for Sears weren't they USA made? I was looking at a rolling maintainence box and it said COO Mexico.