Search results

its like hanging a metal probe in a blow torch. I don't know how it cant sense that. the blue flames are huge!

Read above. That was the first thing I did.

under light blinking codes it reads: "Rapid continuous blinking - Incorrect twinning, incorrect primary polarity. Reverse transformer secondary leads, reverse primary wires." No idea what that means but I see people posting a board replacement would fix this. I see there is a few on amazon...

I have a goodman gmp075-3 furnace in my 2.5 car attached. fired her up today after it sat all summer and the igniter glows orange, the gas valve opens and it lights. I have blue flames for about 3 seconds and then it shuts off. it will try 3 times then stop. The circuit board has a red LED that...

So its that time of the year again and everybody is talking about using the plastic sheets that shrink with heat around your windows. The box claims 35% reduction in heat loss from that room. I find this hard to believe. anyone got real world heating bill data how much this helps? I have a huge...

32 wide x 27 deep. its essentially a 3 car with 2 doors.

They told me the hose reel was fine. Not the feed line. That was my question for my house garage issues with the smaller compressor. Trying to determine if that was a problem not having 1/2" hose why my impact sucked. The regulator question is now for my shop. The setup sheet from Campbell...

I didn't realize the 1/2" kit was the OD. I see that now. Will this one work for me? I have 32 feet to the farthest outlet I would put in. Its about 35 feet total to plum up to the hose reel mounted on the 2 post lift...

So what's your opinions on the air filter/water separator and air regulator on this new compressor, Campbel hausefeld has a real nice set up that's made for this compressor but its 3/8" in and out. I was gonna run the rapid air 1/2" line kit up by the ceiling then have drop downs and also run to...

It was a craftsman cheapy. 7,000RPM 400ftlbs tq rated. It should have done the job but I will be buying some nicer air tools now that the new shop is done. The craftsman compressor it was ran off of I think can only go to 125psi and I have the regulator maxed out at that. It then goes 15 feet...

I just bought a new 80 gallon 5HP 2 stage compressor. 175psi max, 15.8cfm @ 90psi for the new shop I built. This is mostly for auto repair and building race cars. I am concerned with air flow through the hose for the impacts and air ratchets to have the most torque they can. Is it necessary to...

I've been looking for a good air compressor for a little while that would do what I needed. I wanted to not only run air tools but also a tire machine and some light sand blasting. All the 60 gal ones at big box stores didn't seem to have the CFM or were chinese made or were way out of the price...

mine took about 45 days and I had a 6 foot crack in the floor. its never opened up. I don't worry about it. only thing the concrete company can guarantee is it will crack eventually lol.

Picked up an Irwin 6" vise at Lowes for $90. After reading about the Harbor freight ones cracking in half from bad castings I figured I better get something good. From what I can tell this is a rebranded Wilton 11106 which usually goes for $150-$200. Figured that's quality enough for me.

That's wild. I wonder if it is code around here. My dads shop its behind a counter under cabinets. My friends garage is the same way. I don't think anyone follows the rules if it is lol. Hell the one in my house has a washer and dryer in front of it just like my last house. I did have this house...

I'm unsure of code but these are 2 separate pieces and they will not be bolted together or to the wall. I would assume code is for permanent fixtures. I need to move the long one if I want to use the engine hoist to pull a motor out without pushing the car back off the lift. I'll just drag the...

I'm going to wait till spring time to drywall the walls. I've been working on customer cars in there lately and benches and an air compressor are priority right now to make these jobs easier. I have been running over to the other garage for everything lately and I need to get this one fully...

It's been getting cold here lately with a few days in the 30's already. I finished the insulation just in time. All the blow in was done in the ceiling and I had them top off my house. Hoping for lower heating bills this year. Got to fire up the furnace and actually work in the shop with heat...

So what do you think of the Kobalt since you have used it? Lowes right down the street has one I might buy this weekend. How does it keep up with air die grinders and cut off wheels and such? I will be buying a sand blast cabinet soon also. I didn't want to go smaller than 5HP and 80 gallon...

This is the listed specs on 2 websites I found. Air Delivery SCFM @ 90PSI (CFM) 15.8 Air Delivery SCFM @ 100PSI (CFM) 15.7 Air Delivery SCFM @ 175PSI (CFM) 15.6