Search results

my quote I just got for my 28x32 was $3,800 cash deal so it was discounted a little for walls and ceiling. I cant swing it so I grabbed 20 sheets on my own from menards for $260 and had a crew of Mexican guys hang the ceiling so far for $400 cash. looks good so far.

I am in the same boat and started looking last week. I was interested in the harbor freight 60gal until I seen this for $50 more. This thing looks like a bad dude for $999. They said I get $50 off if I open a lowes card so then they are the same price. I kinda trust Kobalt over harbor freight...

I just did a 28 x32 last week and I bought the R13 bats for the walls for $260 from menards and the ceiling I had a company blow in the for $600. So for $860 I had a fully insulated shop. Just save a few paychecks to do that before you buy the heater. I feel like 6 months of running the furnace...

Found a drywall guy to do a cash side job after hours and he hung 20 sheets for $400. I just bought the material which was $240 at menards. Any business I had come out wanted $1,000-$1,200 because the ceilings were so high and they had to work around the lift and the furnace up there. Its a...

Last night I finished up installing the chutes that staple to the back side of the roof plywood to allow venting once the insulation is blown in. Got started on the wall insulation next. I got the front wall that has the doors done and half of the side wall. Man that stuff is nasty. I didn't...

If you use foil backed foam insulation board and fasten it to the roof rafters and seal the inside up it will drop temps inside in the summer and will allow air to still go up through the soffit and out the roof vent on the other side of the foam keeping the air moving under the roof. I would...

I'm **** so I use 3x3 carpet squares. Flat spotting is usually only an issue with bias ply tires but I still do it on radials. The Z06 sat a lot so I always had it parked on the squares as you can see in this photo. Procedure for storing that car when it may sit for a year was: wash and...

Got the furnace installed last week. Used unistrut and some threaded rod. Hung it down at the 9ft level like the instructions said. Decided to vent through the wall since my other garage I went through the roof and it leaks, which I've tried to fix multiple times. I'm no expert so I wasn't going...

I have four 8 foot fluorescent fixtures I put in my house garage about 10 years ago. The ballasts are slowly burning out one by one and its getting dark in there. I have heard you can take the ballast out and direct wire and use a LED replacement. I looked at Menards, Lowes and Homedepot. None...

where are you located now?

Gregsmith equipment told me this is perfectly fine because it is only a 3/4" deep cut not a seem between 2 slabs in the concrete. The bolts must be 3" away from it still though. The installers that came out agreed and do this all the time.

How do you guys that have these at home feel about if you need the bead blaster? I found a deal on one but its a more basic machine and does not have bead blast option.

I have a 50,000BTU Mr heater big maxx hung from the ceiling. Menards has a kit for roof vent for $99 and a kit for wall vent for $350. I really didn't want to attempt the roof vent and have it leak. but damn $350 just for an even shorter pipe going out the wall. pricing seemed crazy. any...

A little change from the normal race car stuff. Had a 66 Triumph TR4 come in and right after a 63 Oldsmobile Starfire with 39,000 original miles. All of the electrical is done. I have outlets in the middle of the doors and on each side of them now. 220 wired for the compressor in the...

if I buy the 50k BTU one and I have 13 foot ceilings, how far should I hang it down from the ceiling? I was thinking 3 feet of threaded rod so it would be around 10 ft.

I have one in my attached garage. its about 30x26. I made a stand to get it up off the floor for code. It heats up fast. zero complaints. My detached building i'm looking at the 50k btu mr heater big maxx ceiling hangar for the 32x28.

natural gas. 18-20" blow in insulation on ceiling, rolls of insulation in walls. drywalled. CHI R8 rated insulated garage doors. 13 foot ceilings tho.

my doors will be closed. I have a man door for entry. long term car projects for winter. cars wont go in and out but once every month if that.

Looks like I will grab the 50k btu one. Thanks.

I have a 900 sq ft 32' x 28' garage. It has 13 ft ceilings. Building is getting insulated right now. Need to mount a furnace in the next week or 2. I am looking at this Mr heater big max unit that is ceiling mounted natural gas. 50,000btu heats 1,500 sq ft. ( does not say ceiling height)...