Search results

  1. A

    Power maxx bandsaw

    I read that thread, I'm not sure if it's the same brand. Some good info on there. Thnx��
  2. A

    Power maxx bandsaw

    I put in a low, sealed bid for a bandsaw and won the auction at our city's surplus auction recently. It's a power maxx 18" bandsaw, I believe the part number is 1-090-018. I have googled the heck out of this thing and have come up with nothing. Does anyone have any knowledge of these tools? I'm...
  3. A

    basic in floor system tuning

    OK without jinxing anything, the system appears to be working. It has run without incident for a couple days now. The slab has gone from 40 degrees up to 60. Its actually a nice temp in the garage., fingers crossed:thumbup:,
  4. A

    No flow in radiant heat loops?

    mine is a gtflow from pex direct on ebay. not good!!
  5. A

    No flow in radiant heat loops?

    i finally got all the air out of my system , i'd hate to open it up and have to start all over
  6. A

    No flow in radiant heat loops?

    i have a similar manifold, my flowmeters dont show anything, the little red discs are just stuck at the top of each one. mine didn't have any instructions regarding adjustment, i email the vendor and ,go figure, got no response:sad:
  7. A

    basic in floor system tuning

    i've got the pump running on high, the flowmeters are on the return side of the manifold, however this is a cheap ebay special manifold, i know i have flow but they are not showing anything
  8. A

    basic in floor system tuning

    ok, so not wanting jinx anything, here is what has happened in the last couple of days... i picked up another replacement unit, installed it, then i replaced all the 3/4" pex with 1". turns out the guy at the hardware store down the road installs outdoor wood boilers, so i got some advice off...
  9. A

    basic in floor system tuning

    i'm here and she has no idea;)
  10. A

    basic in floor system tuning

    r20 wall and roof:thumbup:
  11. A

    here's what i made today ...

    i dont recall where the tower was, but i loved it down there. that whole area was great:thumbup:
  12. A

    here's what i made today ...

    hey i've been to kirkfield. i built a house on canal lake about 10 years ago:beer: nice job btw
  13. A

    basic in floor system tuning

    YEs, its plumbing pex, its what i had. THe filter was added today as a temporary measure to clean junk out of the line, ill replace it tomorow with a less restrictive one. BY melt down i mean the top of element melts then the wires burn off
  14. A

    basic in floor system tuning

    THe manifold is running with all loops wide open
  15. A

    basic in floor system tuning

    THere is one, just couldnt fit it in picture
  16. A

    basic in floor system tuning

    the inline filter was just added today to catch any debris in the water, i'll go to the hardware store tonight and get a proper filter.
  17. A

    basic in floor system tuning

    after much research i decided to switch over to a tankless water heater type setup, i bought the ecosmart 11kw unit. i bought one on ebay, hooked it all up and melted it down within half an hour, the tech line was great and overnighted me parts, i rebuilt it and melted it down again after a half...
  18. A

    any tree experts out there?

    i have a circular driveway, in the centre is a grass "island" which has 5 trees on it. 3 poplar and 2 spruce. the poplars days were numbered as the they were old and only produced leaves on the top, the spruce were ugly but mature. as the leaves finally came out last week on our other trees, i...
  19. A

    Hello From Canada!!

    what ever size your thinking at first, double it!
Top Bottom