Search results

Found this head overhaul kit http://www.airfloinc.com/item/1058 and major overhaul kit http://www.oemair.com/AirCompressorsandProducts/IngersollRandProducts/ReciprocatingPistonPartsandRebuildKits/QuincyReplacementParts/tabid/206/Default.aspx

I did get a return email from Quincy today. "You are right about this being old! RC9 dates back to late 1940's or early 1950's! I have attached a parts book for model 320. Your basic with a RC 9, predates the book I have supplied which is for a RC 13 but is the closest one available. I...

I was buying some shelving from a closed business and saw a compressor. It's for sale. The pump has the following numbers, 320-9-45707L, 4x2-1/2x3 and Quincy. The motor is 3hp (not 3 phase) but looks much larger. The tank is horz. and at least 80 gal. No power in the building so can't run it...

I understand hydrostatic testing but can't see the tank exploding in general use unless there is an overpressure from pressure switch and relief valve failure. Which would be tested before that.

I don't see the T&G in your pics. Have any?

I already have a piece of 6/3 cable and only need 6/2 for running to a welder. Is it OK to just not use white wire and wirenut it or do something else. Thanks.

Resurrecting this thread because I have the same concerns as OP. But what I was wondering is if flexible conduit would be considered a protective sleeve from nails? I would lay it on top of the girts. Can't get rigid metal in there with the studs. Or, what I could do it drill the studs until...

Looks good. BTW, I see you used osb on the ceiling and walls(?). Are you happy with it? I'm contemplating using osb in mine. Thanks.

Just got a flyer in the newspaper (8/14) with a super coupon for $349. Good for 4 until 10/16/11.

Those boxes are on sale for $399 each. The steel should be less than one of those.

The building is starting to take shape. The shed is on the left side. Covered with osb and wrap A couple interior shots. Building up minus 10x10 overhead door and floor. This was on 6/16. There will be a divider wall between shed and shop. It is open in the pic for pouring the floor.

There are 2 sizes depending location. The larger ones are 20" dia x 10" thk. Smaller ones are 18" x 8" thk. I forgot to mention that the town building dept wanted 24" x 12" poured footers instead of the plans sizes and a dry mix. So we had to go with stamped drawings and the pills, no dry mix...

The building is a Conestoga pole building. 24'x24'x11' ceiling (max due to building dept limit of 16' high to peak) 4/12 roof pitch. Attached is a 8'x24' shed with 3/12 roof pitch. Cb structures crew is putting it up. No turning back now. Materials are dropped off on a Fri 6/3. Build starts...

Let's try again. Shed is gone. Thanks CL. My next door neighbor with his toy. Site needed crusher run to get level.

Well I've been hanging out here for almost 3 yrs. After trying to buy a little more land from a neighbor to expand my lot size failed, I decided to just squeeze in another garage. I already have a packed to the rafters 24'x24' garage that's 25 yrs old. So, here it goes. Please let me test out my...

Why wouldn't 2 cuts across work. Dividing the slab into thirds? ~@10'.

I see a lot of guys put studded walls between their posts and finish them with all types of coverings. I assume the studded walls are nailed to the posts and bottom plate sits on or is fastened to the slab. Can slab movement be expected due to change in seasons or for some other reason? The...

I have read that the poly allows the concrete to slide when it shrinks during curing. This helps to prevent cracking. FWIW.

Is there a website that shows pricing for the WHIP lifts? Any distributors in NY?

There are specific screws for structural uses. http://www.grkfasteners.com/en/RSS_1_2_information.htm