Search results

So today I took the "head" brass with seals, o-rings, etc... off, took everything apart. All seals look new, o-rings look new, everything looked good. On the main body the pistons all reciprocated when turning the shaft adapter. It looks new inside but then it should for the handful of times...

Thinking that might be the case. Any exploded views of the pump anywhere? Or are they pretty self explanatory upon disassembly? Thanks!

Thanks - air was purged from hose.

Screen is clean. Here are two videos of it running. The first video is a complete uninterrupted squeeze on the gun. The second is me letting go of the gun when the pressurized water stops. There is a weird vibration noise right before the pressure build after letting go of the gun?

I've had the washer for about 3 years. Used it maybe 5 times. So the other day I go to use it. Starts up a little rough but runs. After 5 minutes the engine cuts out. Now it will only run on full choke and it's slow and rough. So during this troubleshooting I shut the water down as I try to get...

Picked up a Sanborn 5HP 80 Gal. 2 stage compressor. Check oil and looked good. Drained oil to transport horizontally in my truck. I bought 48 oz. of oil and put it back in but it is still more than three inches below the fill hole. I have no idea what the capacity is. Does anyone know? Model -...

Looking at a Sanborn Black Max locally on Craigslist. It's 80 gallon, 2 stage, 5HP. Seller wants $300 with guarantee on it's operation. Looking for something to upgrade from my Devilbiss 20 gal. I don't know the specs but is this good to run air tools like sander, grinder, spot weld cutter...

That *****. Seem at least three of us from SE Pennsylvania had this happen today. I was too sick of what I'd seen to take pictures of my mess. I worked 3 hours in the cold garage cleaning out snow from parts boxes. I didn't want the heat on and melt it all on my stuff. Had mine built by Extreme...

I wish I knew more about pole buildings before building as well. Live and learn. It appears I'll try to find the enclosures for my steel. Good thing I didn't finish my insulation and walls. At least I can get to the inside of my gables at this point.

I don't have the seal shown in the image. Got a ladder out in the blizzard to check it out. Guess I'll need to deal with this and seal it. thanks!

The exterior The red arrow is where the snow comes up in the corrugated gaps under the outside panel. Not a construction guy so the the names of things are not known to me.

There are eaves on. This is the first time in 18 months anything has come in. This blizzard is blowing snow horizontally against that wall. It's finding its way around the eaves to blow in. A unique situation for sure but I want to make sure it doesnt happen again when the walls are finished.

So today we are in the middle of the blizzard here in SE Pennsylvania. Went out to my pole building garage that I had built last summer. Well I was suprised to see about 5-6 cubic yards of snow inside. It was all over my Fairlane and boxes of parts for my '64 Comet build are full of snow. I'm...

I know this is an old post but it looks like something I'd like to use (steel corrugated panel) in my garage. My garage is a pole building. I've studded the walls and insulated and used luaun paneling on the walls. For the ceiling I have trusses on 4' centers. If I fasten these to the trusses...

I'm thinking of building a shelf above my work bench. I was thinking 36" deep x 10' lg. Building it of 2x4 frame with plywood. It would fasten in on the back length of 10' and off to the left in a corner the 36" would be fastened to the side wall. This would leave the right corner away from the...

I got a killer deal on some non-backing insulation that I want to use in the walls of my garage. How do you install it without the insulation falling down over time? Thanks!

I picked up a Sears floor model drill press in excellent condition but without a manual. I'd like to pick up a new belt as this one looks original. Can anyone help me with the model as I cannot find it on a Google search. Here is my tag info: Model Number - 113.23171 Serial or Code Date -...

I bought a Chicago 14" Electric Cut-off Saw - item#61481 from Harbor Freight. I didn't want it for a lot of cutting so I thought it would work fine. My first cut I noticed the flex in the blade. So I thought I'd buy some better blades. I got a few from www.mcmaster.com (14" x 1/8" x 1" arbor). I...

For some reason the handle on my torque wrench came loose. It could slide up and down by an inch or so. It didn't catch to adjust. So I popped off the end cap and tightened the nut up until the handle seemed like it did before. So I then took my old Craftsman beam torque wrench, set a lug nut to...

Humidity is probably the culprit. I'll experiment by checking the floor today and open the doors, it's pretty humid here today. Should happen quickly. Thanks,