Search results

Good idea ! Once the drain is ok(RED), can I wait one day or two before to coat the balance(PINK) as this image ? https://drive.google.com/file/d/0B3EzQ_YvRHmva25fQVltLWJMSGs/edit?usp=sharing Thanks

I have a drying problem for my Epoxy 100% solid with 2:1 ratio ! Normally, according to the manufacturer's instructions, the pot life is 30 minutes. I did some tests with reduced quantity (mix time and mix ratio observed)and I noticed that a pot life is beyond 150 minutes. In the 155...

Can I mix Epoxy, and sands of quartz include in my kit (as previous photo) to fill cracks ?

I have littles cracks to my floor, 1/16 (1mm) ! No filler crack is include in my kit! Here a photo display all item include in this KIT: http://1.bp.blogspot.com/-Vr3GJk4Uruk/Ua-xwqjMceI/AAAAAAAAAbg/gZLHRxFoowI/s1600/colobarctm1.jpg

Here two better photo link, before and after cleaned with my pressure washer at 3500 PSI https://lh5.googleusercontent.com/B5HIlu6T3-Ukk4sexXDsNT6uCAsITdSKyMNpGIpK9rTkdJH91N9bKu0yzKXuOCg1Iato_vz9ZpM=w1434-h778...

In my area, only grinder 7 inch with diamond is available for rental. I have 700 feet square to grind ! How long time should I allow to do this job with a 7-inch grinder ? What thickness of concrete do I remove it?

Which was a distance does you keep your buse from your floor while cleaning ? I just spoke to engineer in building and concrete, and he said me that never use over 2100 PSI for floor, because we can damage a concrete , but if I respects a good distance we can set our pression to 3500 PSI...

On my last message I specified 3500 PSI ! Maybe you prefer kPa, so, if you prefer : 3500 PSI = 24131kPa Link for conversion: http://www.convertunits.com/from/PSI/to/kPa I forgot to specified that I did this test with a ROTO-BUSE or TURBO-BUSE Also for PIC, here a direct link...

Hi, I want apply Epoxy 100% solid on my floor ! I’m not interesting to use acide or diamond grinder to prepare my surface ! I have 700 square ft to covering ! I just tested a little part on my floor with a HighPressure Industrial washing machine at 3500PSI. Before my surface was polished...

Thanks alot for all answer to my question ! It was exactly that I needed !

I heard that a rod NC (National Coarse) give a different force from a NF (National Fine) thread ! Is it true ?

Sorry, I'm french ! If I apply a torque of 150ft/lbs (with torque wrench) on threaded rod 5/8-11 installed on puller to remove a pulley with 3" of bore, then how many TONS my puller give me ? Thanks

I have a manual puller with one rod 5/8-11(UNC). If I apply with a torque wrench 150lbs on this rod, what is a capacity for this puller ? Does a pression is 1 TON, 1/2TON or over ? Thanks

I'm sure that my NUT is not garde 2, but maybe 5 or 8 ! I found another nut that I bought in same time that I made my trailer and a thickness is 15/32". My trailer will be always on my garage, so no problem for corrosion ! Probably that I will use two points throught a tubing, and use a long...

Thanks, I'll think about your ideas! with your method, my tongue will be retractable ! But about other hint to drill through a tube on a center, it is impossible, because a tongue is under this posision, and removable and (draggable) slidable ! I include a draw about this tubing when I build...

With a Electric Cable hoist, on trolley beam, all kit is limited to 1/2 TON by ingeener ! I tried to lift at 1 feet from a floor, and a balancing is perfect ! But I could try at 10 feet today! But I prefer to take your advice here on the forum before ... A trailser's weight exact is 430lbs...

My size tube is 1 1/2" x 3" x 1/8", and nut is solded inside this tube !

Right, but if I use 2, 3 or 4 EyeBolt to lift my trailer, I know that a balance weight will be better, but would impossible to lift near of my ceiling if I use adapted cable as next photo:

Note that I'm french, so sorry for the repetiton of my sentences ! I will try you explain you that I want do, but I'm worried, I would not get my trailer on a toe: In my garage I want lift my domestic trailer(500 lbs as a next photo), nearest of my roof (10 ft), and I want use a EyeBolt fixed...

To be sure, Maybe Grade 2, but it hide inside a square tubing and I can't change because is solded inside of this tubing ! Does this 2400 Lbs is a break point rupture ? or Does 2400 lbs include a safety load 5:1 ? or Does I have to divise 2400 / 5 = 480 ? Thanks