Search results

Does anyone know of a Aerosol Nozzle w/ 19.69in,360 Degrees Extension Hose for Male Stem Spray Cans that will fit a RUSTOLEUM paint can stem? I bout the one listed below and the nozzle hole that goes over the male stem is to big. Thanks...

I'm doing this lane on my back no. Lyft, I am not 25 anymore. This getting old *****. 0 if I had the money to spend, I would have sent it out to be done.

so far I have done from the doors forward with all EASTWOOD products. I have had food luck with EASTWOOD. I have never has luck with POR15. Was not sure if the phosphoric acid and alcohol might work better.

I am cleaning up the rust under my truck. I been wire brush on a grinder then using EASTWOODS Rust Converter and there other products. I was to to make my own rust converter using phosphoric acid and alcohol. Is this good to use or just stay with Eastwoods converter? I am going to need a lot...

D*** auto correct for

They a for half inch bolts to go through and the tube will then be bolted to the frame of the truck, so I will have to drill holes in the frame also. I am looking on facebook marketplace to see what's out there.As far as the drill press goes. Does not need to be super accurate drilling through...

I have a piece of 2"x2"x1/4" mild steel tube I need to drill "14", 1/2" holes straight thru. I only have a 1/2" corded and cordless drill to use. I have tap magic to use but need to get good bits to use. What brand bits should I buy Drill America? I figure I need 1/8, 3/8 and 1/2" bits. Also how...

using it on a snowplow truck and want the wiring to be tight and waterproof

I was told by someone to look for it.I was guessing they have used it in the past

I AM DOING SOME WIREING ON MY TRUCK AND LOOKING FOR HEAT SHRINK TAPE TO GET THAT NIS GOOD. mOST OF WHAT i AM DOING i CAN USE HEAT SHRINL TUBING BUT SOME AREAS NEED TO BE TAPED/ lOOKING FOR3/4" OR 1" WIDE.

I am going to be doing some work on my truck and would like to take the chill off the garage. I have a kero bullet heater but the garage is attach to the house with a bedroom above it. I can not use it do to the smell. Are propane heaters any better? I see the little bullet heaters and the ones...

Color does not matter, mine is black.

I have the HUSKY 56" tool box and love it. I just wish some of the draws were deeper. I am looking fot a 2 draw intermediate middle box that might fit it. I would like the draws to be 4" deep. Does anyone have any suggestions? I would not mind if it was 2 boxes side by side to fit. Thank you

My buddy uses' white vinegar for cleaning carburetors. Seems to work pretty good. I have no experience with any type of cleaners. Besides the vinegar.

What type a fluid do you use in these machines?

Hi all, I am looking at buying a Vevor ultrasonic cleaner. Right now they have them on sale. I am wondering what size to get as it comes in liter size. My main plan is to clean mower and small engine carbs. I do not to small in case I need it for something bigger but not a big unit. Any advice...

If I could afford to pay someone that knows what they are doing to do this I would. But I can't. I have a full bottle of 75/25 gas and a new still in the bag/box of .023" ER70S6 wire so There is no money to lay out there. I guess this is the way I will try.

Why use a gold fixed lens? I have a auto darkening helmet. I will order the .023 wire and tips tomorrow. Do you guys recommend using heat compound to help with warping. I appreciate all the great tips you gul are giving me. Keep them coming. I am a little nervous about welding. On such thin...

Thank you all for the input. Yes, I plan on tack welding all around, to try not to warp the metal. I have 75%Ar/25%CO2 shielding gas so I will go that route. I am doing cab corners and will arch patches on my truck. My eyes really are not q+that good. Anymore, so this should be interesting. I...

I need to weld some patch panels in my truck 18ga. I have welded much heavy steel 1/4"- 5/8" but nothing this light. I just got a Hobart Handler 135 110v unit. Should I use flux core or gas shielding wire? I never used flux core before. The machine can do both and I have mix gas from my large...