Search results

The slab isn't going anywhere. lol, It's poured over a storm shelter, the thinnest part of the slab is probably 3 feet, and up to 6 on the sides, the storm shelter has a rounded roof. I'll get some measurements and hit up homedepot or lowes and see what I can come up with, I just looked up...

Milwaukee has discontinued the D handle saws, all they have are the standard handle, and they're on sale at atwoods for 149, I'm thinking about picking one up tomorrow.

Last saturday while making a taller driveshaft hump in my truck, I took an angle grinder with a wire brush to the knee. Didn't feel too good.

Any car stereo shop has it, and will usually sell it by the foot cheap, All the ones I've worked at had a huge box of scrap wire and would just let people dig through it for what they needed and didn't charge.

Is it feasible to do this? The only reason I want to do it is that it's the smoothest flattest piece of concrete on our property, and it's already got a roof over it, 6 posts of 4x4. I want to turn it into a place where I can move all my metal working stuff too, welder, grinder, saws, etc.. It...

Crayons

Wonder what it would do on the bottom of a boat?...

Re: what did you do in your garage today? Since it's boggy and won't rev, check the spark plug, I had an issue like that with my banshee about 2 weeks ago, forgot to take off the airbox lid, so it was WAY rich, got about 500ft. down the road and fouled both plugs, it barely ran, and wouldn't...

Re: what did you do in your garage today? Check the boot between the carb and cylinder, I had a warrior with the same engine once, and it had a big crack in the rubber boot, sucking too much air and running lean.

Re: what did you do in your garage today? I finally fixed my driveshaft issue. Ever since I did the v8 swap in my extended cab s10, I used a one piece drive shaft, and it has been hitting the bottom of the cab, so last night I ran across the old piece of roof that I saved when they put the...

I've been using the blue permatex threadlocker, and where it gets hot, it doesn't hold very well, about 6 months ago I had the timing plate on my banshee screws backed out, fixed it with a glob of blue on each screw, then I went back to check last night, the screws were barely tight, what's the...

Thanks. That's exactly what I need for the torch storage. :rocker:

My new toy.

The hobart site says for the 210mvp that it requires 6625w, so convert that to amps, it's roughly 27amps. If that's anywhere near correct. lol

The 10 ga coming from the breaker is going to be the welder only. What I did was just remove the old plug, and pull the wire through the wall and hook up the new plug, Its been years since the presses have been used, and I doubt if they ever will again.

Two slots and the "u" ground. Looks like a bigger 110v plug

I asked this on another site but got NO help, except for "pay someone to do it" Right now, there's a 220v 10ga line with a 60a breaker run into the shop for some old printing presses, but they have the old style plug, I bought one of those 50a wall mount outlet boxes that has the socket for a...

About 2 weeks ago I was in sears in the mall, and they had about 7 pairs of them, was thinking about getting a set, now that I've got a mig welder on the way I went back to get a set and they have zero in stock, not even a hangtag for them, I was in another town a few days ago also, same there...

Now that ive got a good welder coming, I need a decent chop saw.. I've been looking at the dewalts and Milwaukee, $199 for the dewalt and $179 for the Milwaukee, I've got dewalt drills, jigsaw and da sander, had good luck with all of them, I don't HAVE to get dewalt, just a good quality that...

Just ordered it, got it for $829 shipped. But it says 7-12 days delivery.. :sad: It'll give me time to round up a decent chop saw and bottle.